Parts for Maytag MVW6230HC2: Top And Cabinet Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

The Whirlpool Lid Strike is an OEM replacement part for Whirlpool top-load washing machines. Located at the top of the washer, the strike assembly securely holds the outer lid assembly in place. 

Causes of a bad strike assembly washer can include cracks or breaks from stresses and vibrations over time, worn-out fasteners loose from use, or damage from forced lid closures.

Symptoms of a bad strike assembly washer include:

• Loose, wobbly lids allowing items to fall inside during loading  
• Inability to tightly secure lids with fasteners becoming stripped
• Clunking or banging noises coming from the lid area during cycles  
• Scratches or marks on surrounding surfaces from misalignment 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore top-load washer models. 

This lid bumper cushions the top-load washer lid as it closes, reducing noise and preventing direct contact between the lid and cabinet. Replace a missing or worn bumper to help protect the lid finish and ensure a smoother close.

• Provides a soft stop at the lid's contact point to absorb impact
• Helps reduce closing noise and lid rattle
• Helps prevent scuffs or chips on the lid edge or cabinet top
• Common signs of failure: bumper missing, flattened, cracked, or louder slam when closing

• Disconnect power before servicing the appliance
• Open the lid and locate the factory bumper position(s) per your parts diagram
• Remove the old bumper and any debris; seat the new bumper firmly in the designated location
• Close the lid gently to verify proper contact and alignment

This left-side door hinge restores proper door alignment and smooth opening on compatible refrigerators. It supports door movement and helps maintain a tight seal for reliable cooling performance. What it does:

• Replaces a worn or bent left door hinge to stop uneven door sag and scraping
• Helps restore correct door alignment for even closing and improved seal
• Reduces noise and binding when opening or closing the door
• Compatible with VMax-style hinge mounting; used where hinge geometry matches OEM design

• One left-side door hinge

• Mounting hardware may be required; confirm included items before beginning
• Disconnect power and empty door bins as needed for safe access
• Support the door during removal/installation to prevent damage or injury

Screw: 8-16 x 3/8 inch.

This is a 10-32 threaded stainless steel screw used to fasten components in compatible Whirlpool appliances. Its corrosion-resistant finish helps maintain a secure connection and long-lasting hold where a small machine screw is required. What it does:

• Fastens panels, brackets, or hardware using a 10-32 machine thread
• Stainless steel construction resists rust and corrosion in humid appliance environments
• Small .276 in length is for shallow mounting applications or thin materials
• Helps stop loose parts that can cause noise, vibration, or poor panel fit

• Use the correct 10-32 driver and avoid over-torquing to prevent strip or damage
• Disconnect power to the appliance when accessing internal components
• Wear eye protection and follow OEM service instructions for safe repairs

This 8-18 x 5/8-inch screw secures appliance panels, brackets, and covers. Replacing a missing or stripped fastener restores a tight fit and helps prevent vibration or loosening where this exact size is specified.

• Fastens sheet-metal or plastic components where a #8-18 x 5/8 screw is called for
• Helps maintain alignment and reduce rattling or vibration
• Replaces stripped, corroded, or missing screws of the same size
• Common symptoms: loose panels, gaps/poor fit, rattling noises, or visible missing hardware

• Disconnect power and shut off gas/water (as applicable) before service
• Match thread and length to the original; replace screws one at a time to keep parts aligned
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving threads are damaged, additional repair (clip, insert, or new nut) may be needed

This is a range hood grease filter. It traps airborne grease and cooking residue so the blower and ductwork stay cleaner and the hood maintains proper airflow.

• Captures grease and particulates from cooking vapors to protect the fan and motor
• A clogged or damaged filter can cause reduced suction, noisy operation, or lingering cooking odors
• Replace if the mesh is clogged, warped, punctured, or if cleaning no longer restores airflow
• Helps maintain ventilation performance and reduce buildup inside the hood

• Disconnect power to the hood before servicing
• Allow the hood and filters to cool before handling
• Open the filter latch or tabs, remove the old filter, and seat the new filter with the tabs/latch aligned
• Restore power; check for proper airflow

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Power Cord is an OEM part for Whirlpool washing machines. It delivers electrical power from the wall outlet to internal components inside the washer cabinet. Made of insulated copper wiring housed within a tough flexible jacket, this cord prevents shocks and ensures reliable power delivery.

Causes can include normal wear over many machine cycles. Rodent chewing, cracking from overly tight bends, or cuts from sharp metal edges are also possible.

Symptoms of a failed power cord include:

• No power to washer control board or motor
• Tripped breaker after plugging washer in
• Bare or frayed copper wiring exposed
• Brittle, cracked cord jacket

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Color: Grey

Color: White

Color: Grey

The Lid Lock Bezel is an OEM replacement part for Whirlpool washing machines. 

Symptoms of a need to replace the bezel include:

• Cracks, discoloration, or visible damage to the bezel
• Looseness or detachment of the bezel from the panel

Causes of a damaged or worn bezel can include accidental impacts, exposure to cleaning chemicals, or general wear and tear over time.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washing machine models.

Color: White

The Bezel-Lid Lock is an OEM component for Whirlpool washing machines. It secures the outer door plastic cover in place during operation. 

Causes of a bad bezel-lid lock can include cracking or breakage from repeated opening and closing of the washer door over several years. Deformation from moisture exposure may also occur.

Symptoms of a bad bezel-lid lock include:

• Looseness allowing the outer door panel to detach or come ajar  
• Inability to fully latch or keep the door tightly sealed
• Damaged lock area where the bezel cover sits  

Compatible with Maytag, Jenn-Air, Amana, and some Kenmore laundry units.
 

The Detergent Dispenser Drawer is an OEM part for Whirlpool washing machines. It is responsible for holding and dispensing detergent and other laundry additives during the wash cycle. The dispenser drawer ensures that these cleaning agents are released at the appropriate times for optimal washing performance.

Over time, the detergent dispenser drawer can become clogged or damaged due to residue buildup, improper use, or general wear and tear. Such issues can hinder the proper dispensing of detergent, affecting the cleanliness of your laundry.

Symptoms of a bad detergent dispenser drawer include:

• Detergent not dispensing properly
• Water not flowing into the drawer
• Leaks from the dispenser area
• Stuck or difficult-to-open drawer

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Bezel is an OEM part compatible with Whirlpool washing machines. This trim piece secures the control console interface within the cabinet opening. Proper mounting provides seamless integration for an aesthetically pleasing appearance.  

Causes of a bad bezel stem from environmental damages over time like cracks or discoloration from cleaning chemicals near the buttons. Repeated impact nicks and dents compromise structural integrity as well.

Symptoms of a bad bezel include:

• Loose hanging appearance no longer firmly fitted  
• Gaps forming entry points for lint and moisture damage
• Detached sections at risk of falling off entirely
• Visual deterioration marring overall style

This Whirlpool replacement bezel restores the finish and protects internal components. It is compatible with brands including Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This is a genuine replacement mounting screw that secures appliance components and panels so parts stay aligned and stable. Installing the correct screw restores proper fit and helps eliminate vibration or loose panels. What it does:

• Fastens panels, brackets, or small components in place
• Replaces missing, stripped, or damaged screws that cause loose parts
• Helps stop rattling, vibration, or misaligned panels
• Restores secure connections after repairs or part replacement

• One mounting screw

• Unplug the appliance or disconnect power before starting work
• Use the correct screwdriver bit to avoid stripping the head
• Tighten until snug; avoid over-tightening which can strip threads or crack plastic
• Keep removed hardware organized so you can reuse existing screws when applicable

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

The Water Inlet Valve is an OEM component compatible with Whirlpool washing machines. This valve controls water flow into the tub by opening at predetermined points in the cycle. Proper water regulation is necessary for optimum cleaning performance.

Symptoms of a bad water inlet valve include:

• Slow or inconsistent filling during initial cycle phases   
• Premature displays of out-of-balance errors due to low water levels
• Inoperable cycles missing crucial wash or rinse stages 

Causes stem from mineral buildup obstructing valve ports over time. Mechanical failure could also prevent actuation from electrical commands sent by the control board.

This Whirlpool replacement valve restores accurate flow control. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This wire harness connects key electrical components to deliver power and signals, restoring reliable operation of the appliance. It replaces a damaged or frayed harness to stop shorts, intermittent power, or control failures. What it does:

• Routes power and control signals between modules, motors, switches, and sensors
• Replaces cracked, burnt, or corroded wiring that can cause intermittent operation
• Helps stop arcing, blown fuses, or tripped breakers caused by damaged leads
• Restores proper connections when loose or broken terminals cause errors or non-functioning components

• One complete wire harness assembly as shown

• Disconnect power (unplug or turn off breaker) before inspecting or replacing the harness
• Note or label wire locations and connector orientation before removal for accurate reassembly
• Secure harness away from heat, moving parts, and sharp edges to prevent wear
• If terminals are damaged, replace the entire harness—do not splice in temporary fixes

This cabinet is the outer housing that protects and supports the appliance's internal components, restoring the unit's structural integrity and appearance. Replaces a bent, dented, or rusted outer shell to reduce vibration and air leaks. What it does:

• Provides the main exterior enclosure and mounting surface for internal parts.
• Restores proper panel alignment to stop rubbing, rattling, or uneven gaps.
• Helps maintain correct airflow by sealing the appliance body.
• Protects wiring and controls from damage and debris.

• Disconnect power and any fuel supply before starting work.
• Installation may require removing panels and transferring brackets or trim; keep original fasteners if reinstalling.
• Cabinet replacements often require two people for safe positioning and alignment.
• Refer to the appliance's service manual or OEM instructions for specific disassembly and reassembly steps.

A replacement cabinet wrap assembly that restores the dryer's exterior cover and protects internal components from dust and damage. Replaces a damaged or dented outer cabinet to improve appearance and maintain cabinet alignment. What it does:

• Replaces a bent, cracked, or cosmetically damaged outer cabinet panel
• Protects the dryer's internal parts from debris and impact
• Restores proper fit and alignment to reduce rattling or gaps
• Helps return the appliance to a finished, factory appearance

• Disconnect power (and gas, if applicable) before beginning any repair
• Remove console/upper panels and any trim to access mounting fasteners
• Handle the panel carefully; edges may be sharp and clips/screws must align for proper fit
• Refer to the appliance's model-specific parts diagram for correct placement and hardware

This replacement name plate restores the appliance's identification label so model and serial information is legible and the exterior looks complete. It's a simple cosmetic and identification part that helps owners read key appliance info. What it does

• Replaces a faded, damaged, or missing identification label
• Restores readable model/serial/manufacturer details for service and registration
• Improves cosmetic appearance where the original label is worn or peeled
• Helps prevent confusion when ordering parts or scheduling repairs

• One replacement name plate

• Clean and dry the mounting surface thoroughly before installing
• Align carefully and press firmly if adhesive-backed; use the original fasteners if applicable
• Handle by the edges to avoid transferring oils or smudges to the label

This leveling foot stabilizes and levels your appliance on uneven floors. It threads into the base so you can raise or lower a corner, reducing rocking and vibration for smoother, quieter operation and proper alignment.

• Provides precise height adjustment to level the cabinet
• Helps prevent wobble, walking, or rattling during use
• Supports stable operation and proper door alignment
• Replaces a missing, stripped, or damaged foot

• Disconnect power; shut off gas/water if applicable
• With help, carefully tilt or brace the appliance to access the foot
• Thread the new foot in by hand, then fine-adjust with a wrench until level and stable
• Ensure all feet contact the floor; recheck level after positioning

The Sound Shield is an OEM replacement part for Whirlpool washers. It is a sheet metal panel installed behind the tub that helps reduce noise and vibration during spin cycles. With absorptive insulation, the sound shield dampens noise produced internally. 

Symptoms of a damaged sound shield include:

• Excessively loud operation, especially during high-speed spins
• Rattles, clanks, or resonant noises from inside the washer  
• Potentially weakened structure allowing tub movement
• Causes of a damaged sound shield can include tears or dents sustained over many high-speed spin cycles. Constant vibration may cause stress cracks or loose rivets.

 It is also compatible with some  Whirlpool, Maytag, Amana, and Kenmore brands.

The Absorber is an OEM part for Whirlpool washing machines. It plays a role in minimizing vibrations and noise during operation by damping the mechanical movements within the machine. 

Causes of a bad Absorber can include the natural wear and tear from continuous use, degradation due to exposure to harsh chemicals or extreme temperatures, and mechanical failure from excessive loads or unbalanced cycles.

Symptoms of a bad Absorber include:

• Increased vibration or shaking during operation.
• Unusual noises like thumping or banging during the spin cycle.
• The washing machine moving excessively or "walking" across the floor.
• Uneven wear and tear on other washing machine components.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This wire shield is a molded protective cover that helps keep wiring routed and protected from heat, abrasion and moving parts. It prevents chafing and reduces the risk of shorts for a safer appliance operation. What it does:

• Covers and routes wiring to protect insulation from heat and friction
• Prevents wires from contacting sharp edges or moving components
• Helps stop intermittent shorts, arcing, or wiring damage that can cause odor or failures
• Maintains proper wire position to support consistent electrical connections

• One wire shield

• Disconnect power to the appliance before beginning any work
• Secure with existing clips or fasteners; do not force or modify the part
• If wiring insulation is melted or damaged, replace wiring/harness before reassembly

This screw is a genuine replacement fastener used to secure appliance panels and components for a reliable fit. It restores proper fastening where original screws are missing, stripped, or damaged. What it does:

• Fastens panels, trim, brackets or small components to keep parts aligned and secure
• Replaces missing or damaged screws that can cause loose panels or rattling
• Restores proper clamping force to prevent movement and wear on adjacent parts
• Matches OEM function and fit when the correct part number is used

• Disconnect power and water before servicing the appliance
• Use the correct driver to engage the head cleanly and avoid stripping
• Tighten until snug; avoid over-tightening which can strip threads or crack plastic

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear panel onto the cabinet frame, ensuring a sturdy connection between housing components.  Proper installation is critical for the washer's structural integrity.

Causes of a bad screw include corrosion from repeated water exposure or stresses from years of use. Loosening can occur from vibrations weakening the threads over time. 

Symptoms of a bad screw include:

• Rear panel detaching from frame opening gaps
• Increased noise and vibrations from a compromised seal  
• Stress on other connections from improper mounting points
• Potential leak paths from openings near hoses or tub areas

This OEM Whirlpool replacement screw helps maintain a tight panel closure. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Hose is an OEM replacement part for Whirlpool washing machines. It is a flexible tube responsible for draining and expelling the used water from the washer tub after each wash cycle.

Symptoms of a faulty drain hose include:

• Water leaks around the hose connections or along its length
• Slow draining or improper drainage of the tub
• Visible cracks, bulges, or damage to the hose material

Causes of a bad washer drain hose can include normal wear and tear over time, exposure to high water pressure or temperatures, physical damage from kinks or pinches, or improper installation or connections.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washing machine models. 

A U-bend retainer designed to secure a U-shaped heating element or tubing in place, preventing movement and vibration for reliable operation. Fits as the replacement hold-down clip used on compatible Whirlpool HVAC and appliance assemblies. What it does:

• Secures U-shaped element or tubing to the appliance frame or mounting bracket
• Prevents rubbing or vibration that can lead to wear or noisy operation
• Helps maintain proper spacing and alignment of the element for consistent performance
• Used where a compact, U-shaped clamp is required to hold components safely

• One U-bend retainer clip as shown

• Inspect the surrounding area and replaced part for damage before installing
• Use basic hand tools; align clip over the U-bend and fasten to the designated mounting point
• Disconnect power and allow components to cool before attempting repair
• Replace with the exact OEM fasteners

The Spring Tension Hose Clamp is an OEM part for Whirlpool washing machines. It is designed to secure hoses in place, preventing leaks by maintaining consistent tension on the hose connections.

Over time, spring tension hose clamps can lose their effectiveness due to metal fatigue, corrosion, or damage from frequent tightening and loosening. This can lead to leaks and improper hose connections.

Symptoms of a bad spring tension hose clamp include:

• Water leaks around hose connections
• Loose or disconnected hoses
• Unusual noises or vibrations during operation
• Water pressure issues within the washing machine

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.