Parts for Whirlpool LGQ8611LW0: 01 - Top And Console, Literature Parts

Fix a dryer that won't start, stops mid-cycle, or runs continuously. This 2-cycle timer controls cycle selection and automatic shutoff. DIY-friendly repair.

Replacement 8-18 x 7/32 machine screw for dryer panels and components. Use when original screw is missing, stripped, or damaged to secure trim and brackets.

Dryer won't start when you press the button? A faulty start switch is often the cause. This switch initiates the drying cycle. DIY-friendly repair.

Fix a dryer that won't start or has no power with this terminal block connector assembly. Common repair for electrical connection issues. Moderate DIY.

Dryer won't start or stops mid-cycle with buzzing? A cracked motor connector housing causes intermittent power to the motor. Quick DIY repair fix.

Replace worn, stripped, or missing 8-18 x 3/8 machine screws that secure control panels, trim pieces, and brackets on your appliance. Restores tight fit.

Dryer won't heat or ignites inconsistently? Faulty wire harness between gas valve and igniter disrupts ignition signals. Simple connector replacement.

Secures the control console to the washer cabinet. Replace if missing, stripped, or rusted to eliminate panel wobble and restore a tight, stable fit.

Secures the control knob to your dryer's control panel. Replace if the clip is broken, cracked, or missing and the knob won't stay firmly attached.

Secures wiring and power cords to the dryer chassis to prevent chafing and loose connections. Replace if broken, missing, or no longer holding wires.

Gray control knob for washer console. Replaces worn, cracked, or missing knobs. Fits timer/selector shaft for accurate cycle and setting selection.

Stack kit connector for dryers. Secures stacked washer-dryer units together. Replace if broken, cracked, or missing to ensure stable stacking.

2-position wire connector for dryers. Replaces damaged, melted, or corroded connectors in electrical wiring harnesses. Essential for restoring connections.

Replacement control knob for dryer control panels. Restores grip and accurate setting selection when original knob is cracked, worn, loose, or missing.

This 8-18 x 5/8-inch screw secures dryer panels, brackets, and covers. Replace missing or stripped fasteners to restore a tight fit and stability.

Secures the control panel to the washer cabinet. Replace if your console strap is cracked, broken, or missing, causing the control panel to sag or shift.

Push-in nut for washers. Secures components and panels inside the cabinet. Replace if cracked, broken, or missing to restore proper assembly.

Dryer won't stop tumbling after cycle or Wrinkle Guard stuck on? This rotary switch controls post-cycle tumbling. Simple twist-out replacement.

Dryer won't power on or trips breaker? This terminal block plug connects power to your dryer's electrical system. Common fix for power issues.

Dryer stops early on auto cycle but works on timed? The moisture sensor control board monitors dryness levels. DIY-friendly repair, 15-20 minutes.

Dryer won't signal when cycle ends or buzzer stuck on? This adjustable buzzer kit restores audible alerts for timers and notifications. DIY install.

Dryer not heating properly or overheating? This temperature switch regulates heat levels to restore safe, effective drying. Simple DIY repair.

Secures the handle end cap to the center of your refrigerator door. Replace if missing, stripped, or lost during handle repairs. 8-18 x 1/2 inch size.

This cap or cover installs on your dryer to protect internal components and maintain a finished appearance. Replace if cracked, broken, or missing.

Wire harness connector that links the control to the buzzer for audible alerts. Replace if damaged, corroded, or missing to restore cycle completion tones.

Replacement mounting screw for securing components and housings in place. Order a new screw if yours is stripped, missing, or damaged during repairs.

Secures control knobs to the panel on washers and dryers. Replace if the clip is broken, missing, or worn, causing knobs to fall off or sit loose.

Secures dryer wiring to the cabinet to prevent rubbing and interference. Replace if your wire retainer clip is broken, missing, or damaged.

Fix dryer electrical connection issues with this terminal. Used for wiring connections in heating and control circuits. Simple installation in minutes.

Covered brands include Whirlpool, Sears, Kenmore, Kitchen Aid, Roper, and Estate. Easy to follow photographs and step-by-step repair procedures.