Parts for Maytag MHW8150EC0: 06 - Tub And Basket Parts

This rotor is the rotating core of the dishwasher's wash motor. Paired with the stator, it spins to drive water circulation through the spray arms, helping restore consistent spray action and cleaning performance.

• Works with the stator to create the magnetic rotation that powers the wash/circulation pump
• Failure can result in little or no spray action and poor cleaning results
• Can lead to intermittent wash or loss of circulation during the cycle

• Disconnect power and water supply before servicing
• Access the wash motor/sump from beneath the unit; removal from the cabinet may be required
• Remove the motor cover/retainer, pull the old rotor straight out, and fully seat the new rotor; handle magnet surfaces carefully
• Reassemble, restore connections, and run a short cycle to check for leaks and proper circulation

This replacement screw secures appliance components such as panels, brackets, and trim. Replacing a missing or damaged fastener restores a tight, rattle-free fit and helps keep your appliance assembled correctly after service or routine maintenance.

• Fastens panels, brackets, or covers to the cabinet/frame for proper alignment and support
• Replaces a stripped, corroded, or missing screw that no longer holds securely
• Helps reduce vibration and rattling caused by loose parts
• Useful when reinstalling components after repairs or part replacements

• Disconnect power; turn off water or gas to the appliance if applicable
• Use the correct driver size; hand-start threads to avoid cross-threading
• Tighten snugly—do not overtighten into plastic or thin sheet metal
• Inspect the mating clip/threads and replace damaged hardware

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

This counterweight is a replacement door balance weight that helps stabilize an appliance door for smoother, more controlled opening and closing. It restores proper door balance and reduces sagging or uneven movement. What it does:

• Adds counterbalance weight to a refrigerator/freezer door assembly for correct alignment
• Helps prevent door sag, slamming, or uneven closing that can compromise the seal
• Reduces strain on hinges and ensures doors operate smoothly
• Quietly stabilizes the door during normal use

• One counterweight

• Disconnect power and empty/remove door contents before starting
• Follow the appliance service manual for door removal/installation; some steps may require two people
• Use appropriate hand tools and avoid forcing parts; retain fasteners for reuse

This washer door bellow seals the opening between the outer tub and the front panel. The drum-light version restores a watertight seal on models equipped with an interior drum light, helping prevent leaks and odor issues from a torn or deteriorated boot.

• Creates a flexible, watertight barrier between the door opening and the outer tub
• Version designed for models with an interior drum light; aligns with the light opening
• Helps the washer contain water properly through fill, wash, and spin cycles
• Common symptoms: water leaking at the door/front, visible tears or cracks, persistent mildew or odor on the boot

• Unplug the washer and turn off water supply before servicing
• Remove necessary front/top access; release inner and outer retaining clamps and remove the old bellow
• Align drain ports and the drum-light opening; seat the bellow fully on the tub and front panel, then reinstall clamps evenly
• Run a quick test and inspect for leaks

The Inner Door Boot Seal Clamp is an OEM replacement part for Whirlpool front-loading washing machines. This clamp is responsible for securely holding the inner door boot seal in place. The door boot seal helps to prevent water leaks and contain washing processes. Its proper placement is ensured by this specialized clamp.

Causes of a bad clamp can include damage from over-tightening during installation and breaking or cracking over time due to normal use.

Symptoms of a bad Inner Door Boot Seal Clamp include:

• Gaps appearing around the edges of the door where water can seep or leak
• The inner boot seal not fitting or sitting flush any longer
• Developing puddles or drips of water outside the washer
• Visible water buildup inside the door seal cavity

It is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Some Kenmore models.

The Baffle is an OEM part for Whirlpool washing machines. This part is located inside the washer drum and aids in lifting and moving clothes during the wash cycle, ensuring that water and detergent are distributed evenly for thorough cleaning.

Common causes of a bad baffle include wear and tear from frequent use, breakage due to heavy or unbalanced loads, or damage from foreign objects that may enter the washer drum.

Symptoms of a bad baffle include:

• Clothes not being cleaned evenly
• Unusual noises during the wash cycle
• Clothes getting tangled or damaged
• Visible cracks or breaks in the baffle

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This spring-style hose clamp secures flexible appliance hoses to fittings, preventing leaks and keeping connections tight during operation. It's a small but critical fastener for reliable fluid containment. What it does:

• Holds a rubber or plastic hose firmly to a barb or nipple to stop leaks
• Keeps drain, inlet, or recirculation hoses seated under pressure and vibration
• Helps prevent water damage and performance issues caused by loose hose connections

• Use pliers or a clamp tool to expand the spring clamp and slide it into position; release slowly to seat
• Inspect hose and fitting for damage and replace if cracked or worn before installing the clamp
• Disconnect power and water and follow appliance safety procedures before servicing

This small black clamp secures a hose, tube or wiring harness to prevent movement and abrasion. It's a direct-fit replacement used to keep connections stable so lines stay routed and protected during normal appliance operation. What it does

• Holds small hoses, tubing or wiring harnesses firmly in place
• Prevents chafing and accidental disconnection from vibration or movement
• Helps maintain routing to reduce stress on attached components
• Commonly used where a compact, non-corrosive clip is required

• Disconnect power before servicing any electrical appliances
• Use appropriate hand tools; avoid over-tightening which can damage hoses

The Tub Suspension Spring is an OEM part for Whirlpool washers. It is responsible for supporting and stabilizing the washer tub during the wash cycle. This spring ensures proper balance and reduces excessive vibrations and movement of the tub. 

A bad tub suspension spring can occur due to continuous use, heavy loads, or accidental mishandling. If you notice symptoms such as excessive shaking or vibrating during the wash cycle, loud banging noises, the washer moving or "walking" during operation, or leaks due to increased stress on the tub and other components, it may be time to replace the tub suspension spring set.

Symptoms of a bad tub suspension spring include:

• Excessive shaking or vibrating during the wash cycle
• Loud banging noises
• The washer moving or "walking" during operation
• Leaks due to increased stress on the tub and other components

Restore your washer by replacing the faulty or worn-out tub suspension spring with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Vent Hose is an OEM part for Whirlpool washers. This flexible hose is used to vent hot, moist air from the washer to the outside of your home, ensuring efficient operation by removing humidity and preventing mold growth inside the washer.

Over time, the vent hose can become clogged with debris, develop kinks, or suffer damage such as tears or holes. 

Causes of a bad vent hose can include the accumulation of lint or debris, physical damage from moving the washer, or general wear and tear over time.

Symptoms of a bad Vent Hose include:

• Longer drying times in washer-dryer combos
• Excessive humidity or mold growth inside the washer
• The washer feeling hotter than usual during operation
• Visible damage or kinks in the hose

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Push-in nut that secures panels, trim, or small components to studs or shafts. Restores a firm, vibration-resistant fastener to help stop loose panels and rattling caused by a worn or missing nut. What it does:

• Secures panels, trim or small assemblies to mounting studs or shafts.
• Helps keep parts aligned and reduces vibration or rattling during operation.
• Common symptom: loose or shifting panels, audible rattling, or components that won't stay in place.
• Designed for a push-fit installation to replace worn or missing fasteners.

• Always disconnect power to the appliance before servicing.
• Push the nut fully onto a clean, undamaged stud until seated; replace damaged studs or mounting hardware.
• If needed, use pliers or a socket to press the nut on evenly—avoid deforming surrounding plastic or sheet metal.

This replacement dishwasher spray nozzle restores targeted water flow to the spray arm for improved cleaning coverage. It fits into the spray arm assembly and helps maintain consistent spray patterns during cycles. What it does:

• Directs pressurized water from the pump into the spray arm for effective cleaning
• Helps maintain even spray distribution across dishes and cookware
• Commonly replaced when spray arm output is weak or dishes are not getting clean
• Prevents clogged or misdirected water flow caused by a damaged nozzle

• One replacement nozzle

• Disconnect power and water supply before beginning repair
• Remove the spray arm to access and replace the nozzle; refer to your model's service manual
• Inspect spray arm seals and grommets during reassembly; replace if worn

This replacement screw secures appliance components and panels so they stay aligned and rattle-free during operation. Replace stripped, missing, or corroded hardware to restore a tight fit and dependable performance. What it does

• Fastens brackets, panels, and internal sub-assemblies in the appliance
• Helps maintain alignment to reduce vibration and rattling
• Replaces missing, rusted, or stripped screws that no longer hold
• Useful when a part won't mount securely or a screw backs out during use

• One screw

• Disconnect power; for gas appliances, also shut off the gas supply
• Compare to the original for length and thread style for the location
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Do not overtighten; if the mounting hole or clip is worn, replace it

The Shock Absorber Washer is an OEM replacement part specific to Whirlpool-brand washing machines. It is a hydraulic device that absorbs the vibrations of the outer washer tub. Note: This is only one shock absorber.

Symptoms of worn or cracked shock absorber washers include:

• Noisy operation as the washer shakes or moves during cycles
• Physical signs of deterioration
• Over time, increased stresses can damage connected components

Causes involve many cycles of compression and release and solvents inside the washer degrading natural rubber. Deteriorated washers no longer absorb vibrations properly.  

This part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This vent fan assembly replaces the exhaust blower that circulates air through the vent system, helping remove smoke, steam and odors from the cooking area. Restores proper ventilation and airflow in compatible range/microwave units. What it does:

• Spins the blower wheel to pull air through the vent and out the exhaust path
• Helps reduce cooking smoke, steam and lingering odors when operating
• Addresses symptoms like weak or no exhaust airflow and unusual fan noise
• Works with the existing housing, ducting and motor connections when compatible

• One vent fan assembly as shown

• Disconnect power to the appliance before starting any repair
• Handle the blower wheel carefully to avoid bending fins or damaging the housing
• Verify fit and electrical connector match the appliance before final assembly

This shield is a protective cover that helps keep internal appliance components safe from heat, debris, and wear. Replacing a damaged shield restores protection to nearby parts and helps prevent further damage. What it does:

• Covers and protects internal components from debris, heat, and contact
• Helps prevent rubbing or chafing on wiring and nearby parts
• Reduces risk of heat-related damage when the original shield is warped or missing
• May stop rattling or vibration caused by a loose or broken shield

• Shield

• Disconnect power (and gas if applicable) before servicing
• Inspect the mounting area for damage or missing fasteners before installing
• Use the correct fasteners and alignment; do not force the shield into place

This heater is the electric heating element that warms air or water so your appliance reaches the proper operating temperature. Replacing a failed heater restores normal heating performance and helps cycles finish correctly. What it does:

• Generates heat needed for normal drying or wash cycles
• Allows the appliance to reach and maintain operating temperature
• Common symptom: appliance runs but does not heat or takes much longer to finish
• Common symptom: cycles complete without expected temperature or sanitizing action

• One replacement heater element

• Turn power to the appliance off at the breaker before starting any repair
• Handle the element carefully to avoid bending or damaging terminals
• Follow the appliance service manual for panel removal and wiring re-connection

The Water Temperature Sensor is an OEM part for Whirlpool washing machines. This sensor ensures the water is reaching the proper temperature at each stage of the wash cycle. Note: The sensor does not include the seal WP8540766. Order separately if needed. 

Causes of a bad temperature sensor can be failures over time due to mechanical wear, thermal stress on electronic components, or damage from leaks/flooding inside the unit.

Symptoms of a bad water temperature sensor include:

• Inability to switch between wash steps or advance through the cycle
• Erratic or inconsistent temperature readings
• Failure alarms or error codes displayed
• Improper or incomplete washing even on high heat settings

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.