Parts for Maytag MTW6600TB1: 03 - Motor, Basket And Tub Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This replacement cap fits over the impeller on the dishwasher circulation/pump assembly to help protect moving parts and maintain proper water flow for effective cleaning. Restores proper fit and helps prevent debris contact with the impeller. What it does

• Covers and protects the pump impeller to help maintain correct water circulation.
• Helps reduce debris contact that can cause reduced cleaning performance or clogs.
• Can address symptoms like poor wash performance, weak water circulation, or unusual pump noise when the cap is damaged or missing.
• Works as the OEM-designed replacement for the pump/impeller cover in compatible units.

• One cap (impeller) as shown.

• Disconnect power and water to the appliance before starting any repair.
• Access typically requires removing the dishwasher tub access panel and pump housing—follow the OEM service manual for your model.
• Inspect the impeller and surrounding seal/gasket; replace damaged seals or fasteners as needed for a proper repair.

The Agitator Bolt is an OEM part for Whirlpool washing machines. This bolt secures the agitator in the center of the wash basket, ensuring it remains firmly in place during the wash and spin cycles. 

Causes of a bad agitator bolt can include regular wear and tear, corrosion due to exposure to water and detergents, or being loosened or damaged by heavy loads or improper handling during maintenance.

Symptoms of a bad agitator bolt include:

• The agitator wobbling or coming loose during cycles
• Unusual noises coming from the washer during agitation
• The agitator not turning properly, resulting in poor cleaning performance
• The bolt showing visible signs of rust or damage

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This washer impeller mounts at the bottom of the tub to generate the water currents that move and roll garments during the wash cycle. Replacing a cracked or stripped impeller restores proper turnover and cleaning performance.

• Creates the wash action by circulating water and moving fabrics through the load
• Secures to the drive hub; worn splines or a damaged center can cause slippage
• Common symptoms: poor cleaning, clothes not moving during wash, clicking/grinding from the wash plate area, visible cracks or looseness
• Direct replacement for the low-profile agitator "wash plate" style

• Disconnect power and turn off water supply before servicing
• Remove the center cap and retaining screw/bolt; lift the old impeller straight up
• Clean the hub splines; seat the new impeller fully and tighten the fastener securely
• Avoid prying against the tub; test on a short cycle to ensure proper wash action

This tub ring (impeller) is the molded plastic ring that helps direct water flow under the wash plate so the washer agitates and rinses properly. Replacing a worn or damaged ring can restore normal wash action and performance. What it does

• Directs and channels water flow beneath the wash plate to support agitation and rinsing.
• Helps maintain balanced water movement for consistent cleaning.
• Worn or broken rings can contribute to poor agitation, clothes remaining soapy, or unusual wash-cycle noise/vibration.
• Works as part of the washplate/agitator assembly to ensure proper water circulation.

• One tub ring/impeller

• Disconnect power to the washer before beginning any repair.
• Remove the wash plate/agitator per your model's service instructions to access the ring.
• Install the ring in the correct orientation and verify it seats fully on the hub; do not force or deform the part.
• After reassembly, run a short test cycle to check for leaks or abnormal noise.

This is a clear plastic hose that runs from the water level switch to the bottom of the tub.

The Water Level Pressure Switch Hose is an OEM part for Whirlpool washers, playing a critical role in the accurate measurement of water levels within the machine.  

Causes of damage to the Water Level Pressure Switch Hose can stem from natural wear and tear over time, leading to cracks or holes in the hose. 

Symptoms of a bad Water Level Pressure Switch Hose include:

• The washer overfills or underfills, indicating a problem with water level detection.
• Unusual noises during the fill cycle, which may suggest air leaks in the hose.
• Error codes related to water level or filling issues displayed on the washer.
• The machine stops mid-cycle due to incorrect water level readings.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This low-profile washplate sits at the bottom of the tub and moves the load through water for proper cleaning. Replace a stripped, cracked, or loose washplate to restore wash action and reduce noise or slippage.

• Mounts to the drive hub to rotate and circulate laundry during the wash cycle
• Helps create water currents and friction to loosen soils
• Worn or stripped splines can cause slipping and poor agitation
• Common symptoms: clothes not moving, poor cleaning results, unusual clicking/grinding from the tub base, visible cracks or wobble

• Disconnect power and shut off water before servicing
• Remove the center cap/cover, then remove the retaining bolt and lift off the old washplate
• Clean and inspect the hub splines; seat the new plate fully and reinstall the bolt—do not overtighten
• Run a short test cycle to ensure proper wash action

The Whirlpool screw is an OEM replacement part responsible for securing various components and parts of your washing machine. These screws are designed to fasten different elements within the appliance, ensuring their stability and proper functioning. The specific location of these screws can vary depending on the washing machine model and design, but they are commonly used to secure panels, brackets, and other components in place.

This part fixes the following symptoms

• Excessive vibration or shaking during the wash or spin cycles
• Loud or unusual noises coming from the appliance
• Loose or wobbly parts within the machine
• Panels or components that become detached or dislodged
• Difficulty in assembling or disassembling parts during maintenance or repair

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Washer Basket Hub is an OEM part for Whirlpool washing machines. It is designed to connect the washer basket to the drive shaft, enabling the basket to spin during the wash and spin cycles. This component ensures that the basket rotates smoothly and efficiently, contributing to the overall performance and functionality of the washing machine.

You should replace the washer basket hub if it becomes worn out or damaged. Causes of a bad basket hub can include regular wear and tear from frequent use, corrosion due to water exposure, or damage from overloading the washer. A faulty basket hub can impair the spinning action, leading to inefficient washing and rinsing.

Symptoms of a bad washer basket hub include:

• The washer basket not spinning or agitating properly
• Loud noises such as grinding or clunking during spin cycles
• The washer failing to complete cycles or properly clean clothes
• The basket being loose or wobbling during operation

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Washer Basket Hub is an OEM part for Whirlpool washing machines. It is designed to connect the washer basket to the drive shaft, enabling the basket to spin during the wash and spin cycles. This component ensures that the basket rotates smoothly and efficiently, contributing to the overall performance and functionality of the washing machine.

You should replace the washer basket hub if it becomes worn out or damaged. Causes of a bad basket hub can include regular wear and tear from frequent use, corrosion due to water exposure, or damage from overloading the washer. A faulty basket hub can impair the spinning action, leading to inefficient washing and rinsing.

Symptoms of a bad washer basket hub include:

• The washer basket not spinning or agitating properly
• Loud noises such as grinding or clunking during spin cycles
• The washer failing to complete cycles or properly clean clothes
• The basket being loose or wobbling during operation

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Outer tub assembly includes: outer tub, tub seal, drive shaft and bearings. To rebuild the tub, order the bearing and tub seal kit W10435302 and the bearing installation tool W10447783. When replacing this part, if you see that your motor stator is broken, search by your model number to make sure you get the right stator for your model.

This lower wire harness connects and routes electrical circuits for the appliance's lower service area, restoring reliable power and signal flow to dispensers and lower controls. It's a direct-fit replacement when the original harness is damaged. What it does:

• Routes and links power and signal wires between lower components and the main control
• Replaces frayed, pinched, or broken wiring that can cause intermittent or no operation
• Helps resolve symptoms such as non-working lower dispenser functions, loss of lights, or erratic component behavior
• Maintains connector fit and OEM routing for proper electrical performance

• Disconnect power (and water if applicable) before starting any repair
• Inspect connectors and terminals for corrosion; replace if found
• Follow for routing and securing the harness to avoid pinch points
• Do not splice or modify the harness; use the exact replacement for safety and proper operation

This clamp secures a washer or dryer hose to its connection to prevent leaks and keep the hose firmly in place during operation. It replaces worn or loose clamps that allow water to escape or hoses to detach. What it does:

• Holds a washer/dryer hose to a nipple, collar or fitting to maintain a sealed connection
• Prevents water leaks caused by loose or corroded clamps
• Stops hoses from slipping off during drain or fill cycles
• Restores proper hose retention and reduces risk of water damage

• Disconnect power and turn off the water supply before starting any repair
• Inspect hose and fitting for damage; replace hose if cracked or frayed
• Use appropriate pliers or a screwdriver for the clamp style; avoid overtightening to prevent hose damage
• Verify a leak-free connection after restoring power and water

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This is a replacement mounting screw used to secure panels, brackets, or components on compatible Whirlpool appliances. It restores proper fastening to reduce looseness and rattling and keep parts aligned for safe operation. What it does

• Fastens trim, panels, brackets or assemblies to the appliance chassis
• Restores secure attachment when original screw is missing, loose, or stripped
• Helps stop vibration-related noise and movement of panels or covers
• Supports correct alignment of components to prevent wear or interference

• Disconnect power to the appliance before beginning any service.
• Start threads by hand to avoid cross-threading; tighten snugly but do not overtighten.
• Keep removed screws organized so replacements go back to their original locations.

Motor shield bumper kit includes 4 bumpers. When replacing this part, if you see that your motor stator is broken, search by your model number to make sure you get the right stator for your model.

This motor stator is the stationary windings for a direct-drive washer motor. Working with the rotor, it creates the magnetic field that turns the basket. Replacing a failed stator restores consistent wash and spin performance. What it does

• Provides the fixed windings for the direct-drive motor
• Works with the rotor to spin and tumble the basket
• Failure can cause no spin/tumble, intermittent movement, or loud humming
• May lead to motor/speed-related error codes and cycle shutdowns

• 1 motor stator assembly

• Disconnect power before servicing; allow moving parts to stop
• Access is typically from the rear; remove the rotor to expose the stator
• Handle the rotor's strong magnets carefully and keep metal objects clear
• Route and seat the wiring exactly as original; tighten mounting bolts evenly

This plate stator is the stationary motor plate used in compatible Whirlpool appliance motor assemblies. It supports the motor's stationary components so the motor can run smoothly and reliably. What it does:

• Secures and positions the motor's stationary winding and magnetic components
• Helps maintain correct air gap between rotor and stator for proper motor function
• Can contribute to noisy motor operation or failure-to-start when damaged
• Supports consistent motor rotation and reduces abnormal vibration

• Disconnect power to the appliance before starting any repair.
• Removal typically requires disassembly of the motor housing; retain fasteners and note orientation.
• Handle carefully—edges and mounting holes can be sharp and fragile.

The Rotor Position Sensor is an OEM part for Whirlpool washing machines. It is responsible for monitoring the position and speed of the rotor, ensuring the motor operates correctly to perform various washing cycles. The sensor sends precise data to the washing machine's control board, which adjusts the motor's function accordingly.

Causes of a bad rotor position sensor can include electrical failures, wear and tear over time, or physical damage from impact or moisture exposure. When this sensor fails, it disrupts the communication between the motor and control board, leading to operational issues.

Symptoms of a bad rotor position sensor include:

• The washing machine not spinning or agitating
• Error codes indicating motor issues
• The machine stopping mid-cycle
• Unusual noises coming from the motor area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

When replacing this part, if you see that your motor stator is broken, search by your model number to make sure you get the right stator for your model. NOTE: Also includes Rotor Bolt. The bolt is not available separately.

This machine screw secures components in place to maintain proper alignment and stability during appliance operation. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, noise, or loosening parts.

• Provides a secure mechanical fasten for panels, brackets, or internal assemblies
• Helps correct rattling, vibration, or loose-fitting parts
• Useful when an original screw is stripped, corroded, or lost
• Sized to match 8-18 thread applications in compatible units

• Disconnect power and shut off water or gas before servicing
• Note original screw location and orientation for correct reassembly
• Start threads by hand to avoid cross-threading; do not overtighten
• Replace any damaged clips or mounts the screw engages

The Bearing Installation Tool is an OEM part for Whirlpool washing machines. This tool is specifically designed to aid in the installation of bearings in the washing machine tub, ensuring proper alignment and secure placement.

This tool is essential for replacing worn-out or damaged bearings, which can affect the performance of the washing machine. Over time, bearings can wear out due to continuous usage, exposure to moisture, or heavy loads. Using this tool ensures that new bearings are installed correctly, preventing potential issues caused by misalignment or improper installation.

Symptoms of bad bearings include:

• Loud, grinding noises during the spin cycle
• Excessive vibration or movement of the washer
• Leaks from the tub area
• The drum not spinning smoothly

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Used to install the bearings in the bearing and tub seal kit, part number: W10435302. When replacing this part, if you see that your motor stator is broken, search by your model number to make sure you get the right stator for your model.

The Bearing and Tub Seal Kit is an OEM part for Whirlpool washing machines. It includes high-quality bearings and a tub seal designed to ensure smooth operation and prevent water leaks. The bearings allow the tub to spin freely and quietly, while the seal protects the bearings from water and detergent, extending their life and the overall efficiency of the washing machine.

Causes of failure for these components can vary but often include water infiltration that leads to rust and deterioration of the bearings, or wear and tear from heavy or unbalanced loads that put additional stress on the seal and bearings. 

Symptoms of a bad bearing and tub seal kit include:

• Noisy operation, especially during the spin cycle
• Water leaking from the bottom of the washer
• The washing machine tub struggling to spin or not spinning at all

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.