Parts for Ge GSC3500R20WW: 02 - Body Parts

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.

Prevents water leaks at the dishwasher door corners during wash cycles. Replace if you notice leaking along the bottom of the door. Clips onto tub rail.

Rubber baffle prevents leaks at dishwasher tub corner. Replace if worn, cracked, or causing water leakage during wash cycles. Snap-fit design.

Replaces broken or worn dishwasher door spring that counterbalances your door. Installs under the unit to restore smooth opening and prevent sagging.

Secures panels, brackets, and hardware in your appliance. Replace when stripped, rusted, or missing to prevent looseness and vibration. Verify fit.

Door won't close or latch properly? This latch keeper secures the door strike so your dishwasher stays closed during cycles. Quick DIY repair.

Thread-forming screw secures dishwasher panels, brackets, and trim components. Replace missing or stripped fasteners to restore proper mounting.

Replacement leveling screw threads into your dishwasher's leveling leg to adjust cabinet height. Install when original is stripped, damaged, or missing.

Dishes not drying or wet after cycle? The heating element heats air during drying. Simple DIY repair with video guide, typically under 30 minutes.

Secures the dishwasher heating element to the tub from underneath. Replace if cracked, stripped, or missing to prevent leaks at the element mounting point.

Secures and positions the heating element in your dishwasher. Replace if cracked, bent, or broken to restore proper element alignment and stability.

Support bracket that secures the heating element in place at the bottom of your dishwasher tub. Replace if cracked, broken, or no longer holding element.

Fix dishwasher overfilling or not filling properly with a new float dome. Protects the float sensor for accurate water level control. Easy 15-minute repair.

Fix dishwasher overflows or underfilling with a new water level float. This part regulates filling by rising with water to signal the switch.

Guides the dishwasher float and connects it to the switch mechanism. Replace if cracked, broken, or worn to restore proper water level control.

Replacement bracket that secures the flood switch in your dishwasher. Holds the leak detection switch in proper position. Needed when bracket is cracked or broken.

Seal washer that sits between the dishwasher pump and motor assembly. Replace if cracked, deteriorated, or causing leaks beneath the pump housing.

Fix a dishwasher that won't drain completely with this filter ball. Sits in the sump track to prevent debris backflow. Easy 30-minute DIY repair.

Dishwasher overflowing or not filling? This float switch detects water levels to prevent overflow and control filling. DIY-friendly repair part.

Connects dishwasher wiring to the water inlet valve. Replace if the plug is burnt, brittle, loose, or corroded to restore a secure electrical connection.

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.

Dishwasher hose chamber connects to the pump assembly to route water in and out during wash cycles. Replace if cracked, chewed by rodents, or leaking.

Leaking during fill or water splashing inside? This dishwasher fill funnel channels incoming water and prevents leaks. Easy DIY replacement project.

Seals the water inlet funnel to prevent drips and direct water into the tub. Replace if you notice leaks at the inlet or water escaping during fill.

Replacement upper dishrack for dishwashers. Installs in the top position to hold plates, bowls, and glasses. Replace if rusted, cracked, or broken.

Replacement slide rail for dishwasher upper rack. Installs on cabinet wall to guide rack in and out. Needed when original is bent, twisted, or broken.

Secures the end of the dishwasher rack slide rail. Replace if cracked, broken, or missing to prevent racks from sliding off track or misaligning.

Upper rack roller assembly for dishwashers. Mounts to the liner to guide the upper rack smoothly in and out. Replace if cracked, worn, or broken. Screws included.

Replace cracked or worn upper rack rollers that prevent smooth sliding. Kit includes studs and wheels for secure rack gliding. Fits GE dishwashers.

Lower dishrack assembly for dishwasher bottom level. Holds plates, pots, and pans during wash cycles. Replace if rusted, cracked, or tines broken.

Replacement roller and axle kit for dishwasher lower racks. Includes 8 wheels and 8 axles. Replace when rollers are broken, cracked, or missing.

Replacement roller and axle kit for dishwasher lower racks. Includes 8 wheels and 8 axles. Replace when rollers are broken, cracked, or missing.

Replacement hose fitting adapter for dishwashers. Connects water supply lines to inlet valve. Order new fitting if original is cracked or leaking.

Dishwasher not filling with water or fills slowly? The water inlet valve controls water flow into your dishwasher. Simple DIY repair, 30-60 minutes.

Replacement mounting screw for dishwashers and electric ranges. Secures panels, covers, and internal components. Order when original is missing or stripped.

Replacement silverware basket with handle for your dishwasher. Needed when original basket is cracked, broken, or has worn holes that let utensils fall through.

Secures dishwasher panels, brackets, and components with 10-32 machine threads. Replace when screws are stripped, missing, or lost during repairs.

Routes water from inlet valve to tub. Replace if cracked, leaking at connections, or worn from age. Installs between valve and tub exterior connection point.

Secures dishwasher drain or inlet hoses to fittings to prevent leaks and slipping. Replace when loose, corroded, or during hose installation. Verify fit.

Secures washer hoses at pump, tub, and valve connections to prevent leaks and hose blow-offs. Replace worn or missing clamps for a tight seal. Confirm fit.

Replacement mounting screw for dishwashers. Secures panels, brackets, or components inside the unit. Needed when original screws are stripped or missing.

Secures dishwasher cabinet to chassis for improved stability. Replace if original brackets are broken, missing, or causing movement and panel gaps.

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.