Parts for Kenmore Elite 79575075910: Case Parts

The Handle Mounting Stud is an OEM replacement part for LG refrigerator doors. It provides a sturdy mounting point for the door handle assembly. Reliable handle connection and support is crucial for dependable door function and access. 

Causes of a faulty stud can include damage from excess weight or impact over time rendering the stud loose or unstable.

Symptoms of a bad stud include:

• Loose or sagging door handle  
• Difficulty opening and closing the refrigerator door  
• Potential for the handle to detach completely
• Safety concerns if the handle connection fails

This OEM LG replacement stud is also compatible with Sears/Kenmore models. 

The Leveling Leg is an OEM part for LG refrigerators. It is one of the four legs at the bottom corners that elevate and provide stability to the entire appliance.

Causes of failure can be broken mounting points that no longer provide secure elevation, full compression of the built-in cushioning, or damage from impact on an unlevel floor.

Symptoms of a faulty leveling leg include:

• Excessive shaking or vibrating of the refrigerator
• Door alignment issues where doors are difficult to open or close fully
• Visible leaning or misalignment of the refrigerator cabinet

This OEM LG part is also compatible with some Kenmore models.

This duct connector is the OEM-style assembly that links dryer exhaust sections or connects the dryer outlet to the vent duct, helping guide airflow out of the appliance and maintain a secure vent connection. What it does:

• Provides a secure connection between dryer exhaust outlet and vent ducting
• Helps direct hot, moist air safely out of the appliance vent system
• Reduces gaps that can cause air leaks or lint buildup at the connection
• Fits where the original connector attaches to the dryer vent assembly

• Turn off and unplug the appliance before attempting removal or installation
• Inspect surrounding ducting and lint traps; clean before reassembly to reduce fire risk

This is an ice storage bucket that collects and holds cubed ice from the refrigerator ice maker, making it easy to dispense and store ice for daily use. It replaces a cracked, warped, or missing ice bin to restore proper ice handling. What it does:

• Collects and stores ice produced by the ice maker so cubes are ready to dispense
• Guides ice to the dispenser/door chute or manual access area to prevent spills
• Prevents ice jamming caused by broken or deformed bins
• Helps keep ice contained and sanitary inside the freezer compartment

• Disconnect power before servicing the ice maker area to avoid injury
• Remove any remaining ice before removing the old bucket to reduce spills
• Align bucket tabs/guides and slide into place until it seats naturally; do not force
• If ice does not dispense after install, check ice maker alignment and clear ice chute

A small protective cap that covers and protects a component connection or opening from dirt and moisture, helping maintain proper function and prolong component life. Simple replacement when the original cap is cracked, missing, or worn. What it does:

• Covers exposed fittings, terminals, or openings to keep out debris and moisture
• Helps prevent leaks or contamination at the sealed connection
• Restores a secure fit when the original cap is cracked, split, or degraded
• Commonly used where a small, removable protective seal is required

• Inspect mating surface and surrounding gasket/seal before installing; replace other damaged parts as needed
• Press the cap firmly into place until fully seated; no special tools usually required
• Wear gloves and disconnect power or water supply if working near energized or pressurized components

This drum roller replaces a worn support wheel that helps the dryer drum spin smoothly, reducing noise and preventing drum wobble. Restores quieter operation and proper drum alignment. What it does:

• Supports the dryer drum so it rotates evenly during a cycle
• Reduces squealing, scraping, or grinding noises from the drum area
• Helps stop drum wobble and uneven spinning that can cause wear
• Can reduce rubbing or burning smells caused by a seized or worn roller

• Disconnect power before starting any repairs; electric shock hazard.
• Typically accessed by removing the dryer front panel and drum—use care to support the drum.
• Inspect adjoining idler, belt, and rear rollers when replacing for complete repair.

The Shelf Assembly is an OEM replacement part for LG refrigerators. It provides a movable shelf surface for organizing and storing items in the refrigerator or freezer compartment. 

Symptoms of a bad shelf assembly include:

• Sagging or bowing of the shelf surface 
• Difficulty in moving or removing the shelf
• Damage or cracks in the frame or wire grid
•  Inability to bear weight as intended

Causes of failure can be repeated overloading, accidental impacts, or normal wear and tear over time. 

This authentic LG shelf assembly is also compatible with refrigerators by Kenmore models.

This drawer tray assembly is the platform that supports a refrigerator storage drawer and guides it along the slides. Replacing a cracked or damaged tray restores smooth operation, proper alignment, and dependable support for your food items.

• Supports the drawer bin and its contents inside the compartment
• Interfaces with the slide/rail system for smooth in-and-out travel
• Helps maintain proper alignment so the drawer opens and closes fully
• Common symptoms: cracked or broken tray, broken tabs, wobbling drawer, sticking/binding, or difficulty closing

• Disconnect power and empty the drawer before service
• Remove the drawer per your model's instructions; release tabs or screws securing the tray
• Position the new tray, ensuring tabs/rollers seat correctly; reinstall any fasteners
• Reinstall the drawer and check for smooth travel before reloading

This supporter cover is a replacement internal bracket that helps secure the TV's back or front cover, restoring proper panel alignment and reducing movement. Fits where the cover needs a mounting or support point to sit flush and stable. What it does

• Provides structural support to the TV cover or bezel so panels align correctly.
• Prevents cover flexing or sagging that can cause gaps or rubbing.
• Helps stop rattling or vibration-related noise caused by loose cover panels.
• Restores proper mounting points for screws or clips that hold the cover in place.

• One supporter cover.

• Unplug the TV and place it on a soft, flat surface before beginning.
• Remove the external cover or bezel per the service manual to access the mounting location.
• Keep track of screws/clips; use the same hardware unless replacement is specified.

This Tray Cover Assembly replaces a damaged or missing outer cover to protect and contain the tray area, restoring proper fit and helping prevent spills or debris buildup. It's a direct-fit replacement designed for easy swap-in. What it does:

• Covers and protects the tray area to keep contents contained and reduce spills
• Restores proper alignment and sealing of the tray opening
• Replaces cracked, warped, or broken covers that cause leaks or poor fit
• Helps maintain appliance appearance and hygiene by covering exposed tray parts

• One tray cover assembly as shown

• Disconnect power (and water if applicable) before beginning any repair
• Handle part carefully to avoid scratching or cracking plastic
• Align tabs and snap or fasten in place; verify clips engage fully
• Test fit and basic operation before reassembling remaining panels

This deodorizer assembly helps reduce food odors inside the fresh-food compartment by neutralizing smells at the source for a fresher-smelling refrigerator interior. Designed to fit into the factory deodorizer housing and integrate with the fridge's air system. What it does

• Contains the deodorizing element that helps neutralize common food odors in the refrigerator compartment
• Works with the appliance's air circulation to continuously treat internal air and reduce lingering smells
• Commonly replaced when odors persist despite cleaning or after the deodorizer element has reached end of life
• Matches the original shape and connectors to restore proper fit and function

• Disconnect power to the refrigerator before attempting removal or installation to avoid electrical shock
• Access typically requires removing the deodorizer cover inside the fresh-food compartment or freezer—handle panels and clips carefully
• Avoid exposing the deodorizer element to water; replace the entire assembly if the element is saturated or damaged
• Reassemble panels and restore power, then allow the refrigerator to run for a few hours before evaluating odor reduction

This rail guide assembly replaces a worn or broken refrigerator drawer slide to restore smooth opening and closing and keep the drawer aligned. Fits front-to-back mounting rails used on compatible LG refrigerator drawers. What it does:

• Supports and guides the freezer/fridge drawer along its track for stable movement
• Replaces damaged, bent, or worn rails that cause sticking, sagging, or misalignment
• Helps reduce rattling and uneven drawer travel when properly installed
• Works with the matching slide carriage and mounting hardware to maintain drawer function

• One rail guide assembly as shown

• Inspect drawer slides and matching carriage for wear; replace both sides if needed for best performance
• Mounting screws/hardware—use existing hardware or verify required fasteners before starting
• Disconnect power to the appliance before working in the cabinet; remove stored items from the drawer

This ferrite magnet is a replacement magnetic element used in compatible appliance assemblies to help secure components and maintain proper alignment. It restores magnetic retention and reduces shifting or misalignment during operation. What it does:

• Provides magnetic retention for panels, assemblies or components that rely on ferrite magnets
• Helps maintain proper alignment and secure closure where magnets are used
• Can reduce noise and vibration related to loose magnetic components
• Useful when a brittle, cracked or weak magnet no longer holds parts in place

• Disconnect power and follow the appliance manufacturer's safety instructions before servicing
• Handle the magnet carefully; ferrite material is brittle and can chip or shatter if dropped or struck
• Keep magnets away from sensitive electronics and credit cards; avoid pinching fingers between strong magnets
• If the original magnet is bonded or embedded, some adhesive or light trim may be needed for proper fit.

The Door Gasket is an OEM part for LG refrigerators. It serves as a thermally-insulating boundary around the freezer door helping maintain intended sub-freezing temperatures.

Causes of a bad freezer door gasket can involve hardening of the rubber from prolonged exposure to freezer climate conditions. Mineral accumulation aggravates inflexibility over time as well.

Symptoms of a bad freezer door gasket include:

• Difficulty closing the freezer door fully or securely
• Reduced energy efficiency from cold air escape
• Premature evaporation of the door seals' adhesive
• Gap formation around the door exposing food to warmer air

This OEM LG part is also compatible with some Kenmore models.

This freezer handle assembly replaces a broken or worn freezer door handle to restore a secure grip and normal door operation. Durable molded construction matches OEM fit for a clean, factory look. What it does:

• Provides a solid grip to open and close the freezer door easily
• Replaces cracked, loose, or missing freezer handles to prevent leaks and maintain seal
• Restores proper handle alignment for smooth door operation
• Helps avoid further damage to the door finish or mounting points from a loose handle

• Disconnect power to the appliance before starting any repair to avoid injury.
• Use basic hand tools (screwdriver, socket) and keep fasteners for reinstallation; follow the manufacturer's service instructions.
• Handle may attach with screws or hidden fasteners—inspect mounting area and remove any trim as needed.

This door gasket assembly seals the refrigerator door to help maintain proper internal temperature and reduce energy loss. Replacing a worn or torn gasket restores a tight seal for better cooling and food preservation. What it does:

• Forms an airtight seal between the refrigerator door and cabinet to limit warm air entry
• Helps prevent frost buildup and condensation that can occur with a failing seal
• Reduces compressor run time caused by air leaks, improving cooling consistency
• Commonly replaced when gasket is torn, deformed, hard, or no longer seats properly

• Disconnect power to the appliance before starting any repair.
• Inspect the door edge and mounting channel; remove any debris before seating the new gasket.
• Warm the gasket slightly if needed to help it seat; avoid open flames or overheating.
• Verify even seating around the entire door and check door alignment; run a paper test to confirm a consistent seal.

Door gasket assembly provides a secure, flexible seal around the appliance door to prevent leaks and maintain proper internal conditions. Replacing a torn or worn gasket restores sealing performance and reduces leaks, drafts, or temperature loss. What it does:

• Forms the primary seal around the door to keep water, air, and temperature inside the appliance.
• Stops visible leaks or pooling around the door opening.
• Helps prevent temperature fluctuations, frost buildup, or loss of cleaning/drying performance caused by a poor seal.
• Addresses visible damage symptoms such as cracks, tears, deformation, or persistent odors around the door edge.

• Always disconnect power (and water, if applicable) before starting any repair.
• Remove the old gasket carefully; inspect and clean the door channel and mounting surface before installing the new gasket.
• Ensure the replacement gasket is fully seated and any retaining clips or fasteners are secured per OEM instructions; test the door for proper fit and sealing.

The French Door Mullion is an OEM part for LG refrigerators. It is a flap located between the two doors of a French door refrigerator, helping to seal the gap and maintain the internal temperature by preventing warm air from entering when the doors are closed. This component is crucial for energy efficiency and proper functioning of the refrigerator.

Over time, the mullion can wear out or become damaged due to frequent use, impact from door closures, or issues with the hinge mechanism. Causes of a bad French door mullion include wear and tear, physical damage, or a faulty hinge that causes misalignment.

Symptoms of a bad French door mullion include:

• The mullion not folding or unfolding correctly
• Visible cracks or damage to the mullion
• Warm air entering the refrigerator, affecting cooling
• Increased energy consumption

This OEM LG part is also compatible with Sears/Kenmore models.

This drawer guide is the plastic slide that supports and guides a freezer or refrigerator drawer for smooth, stable opening and closing. It replaces a worn or broken guide to reduce sticking, sagging, and drawer misalignment. What it does:

• Supports the drawer on its track so the drawer opens and closes smoothly
• Keeps the drawer aligned to prevent binding, scraping, or uneven movement
• Restores proper engagement with the drawer slide to stop sagging or partial drops
• Helps reduce noise and wear caused by a damaged or missing guide

• Disconnect power or unplug the appliance before accessing interior components
• Remove the drawer and any contents or glass shelves first to avoid breakage
• Typically secures with simple clips or a few screws; do not force parts—line up tabs before seating
• If metal parts are bent or the mating slide is damaged, inspect both sides and replace as needed

This door basket assembly restores usable storage on your refrigerator's door. It mounts to the inner door liner to hold bottles, jars, and condiments securely so items stay organized and easy to reach.

• Provides shelf-style storage on the door for condiments, jars, and beverages
• Attaches to molded slots on the door liner and locks into place
• Common symptoms: cracked or broken bin, broken mounting tabs, bin falls off or won't stay seated, missing bin
• Restores proper organization and prevents spills from a loose or damaged bin

• Disconnect power to the refrigerator before servicing
• Empty the bin; lift straight up to remove the old basket
• Align the new basket with the door's mounting tabs/slots, then push down until fully seated
• Verify secure engagement before loading; avoid overloading to prevent damage

This replacement door basket restores secure, organized storage on your refrigerator door. It holds bottles, jars, and condiments on the inner door to keep items upright and reduce spills when opening and closing.

• Mounts onto the door liner rails/slots to provide on-door storage
• Keeps contents upright during door movement to help prevent tipping
• Helps address issues such as a cracked or missing bin, a basket that won't stay seated, or items falling from a damaged bin

• Remove contents and lift the old basket straight up and out of the door liner channels
• Align the new basket with the mounting tabs/slots and press down until fully seated and secure
• Verify the door closes freely, then reload contents; avoid overloading the bin
• Handle rigid plastic carefully; allow cold parts to warm to room temperature to reduce risk of cracking

This refrigerator door basket assembly replaces a cracked or missing door bin to restore secure storage for bottles, jars, and condiments. It mounts to the door liner to keep items organized and easy to reach. What it does:

• Attaches to the door liner to provide shelf-style storage
• Restores lost capacity and organization when a bin is broken or missing
• Helps keep beverages and condiments stable during door movement
• Common symptoms: cracked plastic, broken locking tabs, bin won't stay seated, items falling, door interference

• 1 door basket assembly

• Unplug the refrigerator and remove items from the affected bin area
• Lift the old bin straight up to disengage the tabs, then pull it out
• Align the new bin with the door liner mounts and press down until fully seated
• Verify the door closes freely and avoid overloading the new bin

Replace a cracked or missing door bin with this door basket. It mounts to the refrigerator door to hold bottles and condiments, restoring safe, convenient storage and helping the door close properly.

• Attaches to the inner door to organize bottles and small items within easy reach
• Replaces a bin that is cracked, warped, or has broken locking tabs
• Symptoms include: bin falls off, won't stay seated, spills, or difficulty closing the door
• Restores designed door storage capacity and stability

• Unload the door and lift the old bin up and out of the mounting slots
• Align the new basket with the slots and press down until fully seated on both ends
• Do not force; confirm it's locked in before loading items
• Follow appliance safety guidelines; avoid overloading the bin after installation

This is a replacement door basket that mounts to the inside of the refrigerator door to hold bottles, jars, and other items securely, restoring convenient, organized storage space.

• Provides stable storage on the door, preventing items from tipping or falling
• Common fix for cracked, broken, or missing door bins
• Helps when items no longer fit properly on the door
• Restores original door storage capacity after damage or wear

• Unplug the appliance and wear cut-resistant gloves
• Open the door and lift the old bin straight up and out of the mounting tabs
• Align the new basket with the tabs and press down until fully seated
• Verify it is secure before loading items

This bushing is a replacement shaft support that stabilizes a rotating assembly and helps reduce wear and noise. It restores smooth movement and helps maintain proper alignment for the appliance component. What it does

• Supports and centers a rotating shaft or drum to reduce wobble and rubbing
• Reduces noise and friction from worn pivot or support points
• Helps prevent uneven wear on mating parts and prolongs assembly life
• Commonly replaced when you hear squeaking, grinding, or notice excessive play

• One bushing

• Inspect mating surfaces and replace any damaged clips, seals, or fasteners as needed
• Use basic hand tools; hold the assembly steady and press the bushing squarely into place
• If the bushing is press-fit, use a suitable driver or press to avoid damage
• Disconnect power and follow all safety precautions before beginning repairs

This door stopper mounts at the hinge to limit the refrigerator door's opening angle and provide a positive stop. Replacing a worn stopper helps protect the hinge, prevent over-swing, and promote a smooth, even door seal.

• Limits door opening at the hinge to prevent overextension
• Helps maintain door alignment and consistent gasket contact
• Reduces impact that can loosen hinges or damage the cabinet
• Common symptoms: door swings too far, clunks at full open, doesn't stop smoothly, or shows visible wear at the stop

• Disconnect power and remove items from the door to reduce weight
• Support the door; remove hinge cover and fasteners as needed to access the stopper
• Install the new stopper in the same orientation; tighten hardware securely
• Verify door swing and sealing after reassembly

The Lower Refrigerator Door Hinge is an OEM part for LG refrigerators. This hinge supports the refrigerator door, allowing it to open and close smoothly while maintaining proper alignment. It is designed to handle the weight of the door and ensure a secure and stable operation over time.

Causes of a bad lower refrigerator door hinge can include regular wear and tear, physical damage from overloading or impacts, and gradual loosening over time. A faulty hinge can lead to misalignment, difficulty in opening or closing the door, and potential damage to the door seal.

Symptoms of a bad lower refrigerator door hinge include:

• The door not closing properly or staying open
• Sagging or misaligned door
• Unusual noises when opening or closing the door
• Gaps in the door seal, causing cooling inefficiency

This OEM LG part is also compatible with Sears/Kenmore models.

This slide rail guides and supports a single appliance drawer or pull-out door so it opens and closes smoothly and stays aligned. Replaces a worn, bent, or noisy guide to restore proper movement and stability. What it does:

• Provides a rolling/sliding track for a drawer or pull-out door to travel smoothly
• Replaces damaged or worn rail that causes sticking, misalignment, or uneven movement
• Helps keep the drawer properly supported and prevents sagging or binding
• Works as a direct-fit replacement when the original rail is broken or worn

• One slide rail (single left or right guide)

• Disconnect power and empty the drawer before starting repairs
• Typical installation requires removing the drawer and fastening the rail with existing screws or clips
• Inspect mating hardware and replace any stripped screws or broken clips for secure fit

This slide rail is a direct-fit replacement that restores smooth, reliable movement to a refrigerator or freezer drawer. It replaces a worn or broken glide so the drawer opens and closes without sticking or sagging. What it does:

• Replaces a damaged or worn drawer glide to restore proper sliding action
• Supports the drawer to keep it level and reduce binding or sticking
• Reduces noise from grinding or scraping during drawer movement
• Helps maintain correct drawer alignment for proper sealing and operation

• Verify left/right orientation and part number before installation
• Remove contents and disconnect power if working near electrical components
• Typical installation uses existing mounting points and hardware; save original fasteners when possible

This ice maker gear drives the ejector blades that push ice from the tray into the bin. Replacing a worn or broken gear restores proper harvest cycles and stops grinding or slipping during ejection. What it does:

• Turns the ice maker ejector to release ice cubes during the harvest cycle.
• Stops or reduces grinding noises and slipping when the gear teeth are stripped or damaged.
• Helps restore regular ice production when the ejector no longer rotates.
• Works as the replacement driven gear in compatible LG ice maker gear trains.

• Disconnect power before servicing the ice maker to avoid shock or injury.
• Remove the ice maker assembly to access the gear; follow OEM instructions for disassembly.
• Inspect the mating gear, motor shaft, and ejector assembly for wear—replace additional damaged parts as needed.
• Use the matching part number to ensure fit.

This center hinge assembly replaces the middle hinge that supports and guides the refrigerator center door, restoring smooth door alignment and secure closing. Designed to fit the original hinge location and mounting points for a factory-style repair. What it does:

• Supports the center refrigerator door and helps maintain proper door alignment.
• Provides the pivot and stop points the door uses to open and close smoothly.
• Helps eliminate sagging, uneven gaps, or doors that don't latch reliably.
• Restores correct door movement when the original hinge is worn, bent, or damaged.

• Designed for direct replacement; match part to your appliance and mount at the center hinge location.
• Use appropriate hand tools and follow manufacturer torque recommendations for hinge fasteners.
• Remove power and empty doors of heavy contents before starting to reduce strain and risk of tipping.
• If door alignment issues persist after replacement, check adjacent hinges and door gaskets for wear.

The Refrigerator Hinge assembly,center is an OEM replacement part for LG refrigerators. This center hinge assembly plays a role in connecting the refrigerator doors, facilitating their smooth opening and closing motion. 

Causes for replacement include normal wear and tear, accidents, or loading the doors with excessive weight over an extended period.

Symptoms of a bad hinge assembly include:

• Doors that don't close flush or have gaps 
• Doors that are difficult to open or close
• Loose, squeaky, or wobbly doors
• Damaged or broken hinge components

This OEM LG part is also compatible with select Sears/Kenmore brand models.

This turntable roller ring sits under the glass tray and allows it to rotate smoothly for even heating. Replace a worn, warped, or broken ring to restore stable rotation and consistent cooking performance.

• Supports the glass turntable and rides on built-in rollers for smooth, quiet movement
• Keeps the tray level and centered to promote even heating
• Common symptoms: tray not turning, uneven cooking, scraping/grinding noises, or a wobbly/slipping turntable
• Restores proper interaction between the turntable, drive coupling, and motor

• Unplug the microwave or switch off the breaker before servicing
• Remove the glass tray; lift out the old ring and clean the track
• Place the new ring with the rollers facing down on the track; reseat the tray on the center drive coupling
• Test rotation with a microwave-safe cup of water

The Spanner Wrench is an OEM replacement part for LG refrigerators. This tool allows you to adjust the door hinges to ensure the doors are level and aligned properly. A well-aligned door is crucial for maintaining the internal temperature and efficiency of the refrigerator, preventing energy loss and ensuring food is stored under optimal conditions.

Symptoms that you might need to adjust the door hinges and potentially need this wrench include:

• Doors not closing properly or sealing tightly
• Visible gaps between the door and the main body of the refrigerator
• The refrigerator tilting or not sitting level

This spanner wrench is also compatible with some Sears/Kenmore refrigerators. 

This tension spring provides the restoring force for a moving component in select LG appliances, helping doors or internal mechanisms return to their resting position and maintain correct alignment. It's a small mechanical part that restores motion reliably when functioning. What it does

• Supplies tension to return or hold a moving part (door, hinge or internal linkage) in its intended position
• Restores smooth, consistent motion and helps prevent slamming or sagging caused by worn springs
• Common symptom: door or component does not return, feels loose, or has uneven movement
• Works as a direct-fit service part when the original spring has stretched, broken, or lost tension

• One spring (quantity: 1)

• Inspect the matching mounting points and hardware before installing; replace any damaged clips or pins
• Use care when removing/installing under tension; wear eye protection and follow safe-handling practices
• Only install the part in appliances that list the same part number/location; do not force mismatched parts

This hinge secures and guides a refrigerator door for reliable opening and closing. It restores proper door alignment to help maintain an airtight seal and prevent sagging or rubbing. What it does:

• Supports the refrigerator door and attaches it to the cabinet frame
• Guides smooth door movement and maintains alignment
• Helps prevent door sag, uneven gaps, and items catching when opening/closing
• Reduces rubbing, scraping or abnormal door noise caused by a worn hinge

• Disconnect power and remove food from the door before starting; support the door to prevent dropping
• Use the factory mounting screws and follow OEM torque and alignment steps
• Check door position and seal after installation; adjust hinge mounting if necessary

This upper hinge assembly supports the refrigerator door at the top, providing a smooth pivot and proper alignment. Replacing a worn hinge restores even gaps and a tight seal to help maintain consistent cooling performance.

• Supports the door's weight and provides the top pivot point
• Maintains alignment for correct gasket compression and a tight seal
• Helps the door open and close smoothly without rubbing or binding
• Common signs of wear: door sagging or misalignment, rubbing/clicking noises, and poor sealing or condensation around the gasket

• Unplug the refrigerator before servicing.
• Remove the top hinge cover; retain screws and any shims for reuse.
• Support the door with a helper while removing and installing the hinge.
• Position the new hinge, align the door, then tighten screws and verify smooth swing and full gasket contact all around.

This replacement lever spring restores tension to a lever-style mechanism so the lever returns and operates reliably. Use it when a worn spring causes the lever to stick, slip, or fail to engage properly. What it does

• Replaces the worn or weakened spring in a lever assembly to restore proper return tension
• Helps prevent the lever from sticking, slipping, or failing to stay engaged
• Restores consistent mechanical movement for reliable operation
• Reduces intermittent or flaky lever behavior caused by a damaged spring

• Disconnect power to the appliance before starting any repair
• Inspect the lever assembly and mounting points; replace only the spring explicitly listed
• Use appropriate hand tools and pliers; avoid overstretching the spring during installation

This lever spring is a small replacement tension spring that restores proper return and engagement for a lever assembly. It helps maintain reliable lever movement and secure latching where a worn or broken spring causes play or non-return. What it does:

• Provides return tension for a lever or latch assembly so the lever snaps back into place
• Helps maintain proper engagement of latch/actuator mechanisms
• Common remedy for a loose, sagging, or non-returning lever
• Works as a direct-fit replacement when the original lever spring is damaged or fatigued

• One replacement lever spring

• Disconnect power and/or unplug the appliance before starting any disassembly
• Handle small springs carefully; keep track of orientation and any retaining clips during removal
• Installation may require partial disassembly of the trim or latch assembly

This lever holder is the replacement mounting bracket that secures the door lever so the microwave door operates smoothly and reliably. It restores proper lever alignment to help the door latch and release as intended. What it does:

• Secures the door lever assembly so the door can latch and release properly
• Keeps the lever aligned to prevent binding, sticking, or loose movement
• Helps restore normal door operation and user access to the oven cavity
• Common symptom: door feels loose, lever moves freely, or door will not latch

• Disconnect power before beginning any repair to avoid shock or injury
• Remove the outer cabinet or door trim only as needed to access the lever area
• Handle door components and glass carefully to avoid damage or injury

This electrical wire-harness connector links wiring to the appliance's control or component, restoring a secure electrical connection and helping eliminate intermittent power, no-start, or erratic component behavior. What it does:

• Provides a secure mating point between the wiring harness and an appliance control, motor, or sensor
• Restores reliable electrical contact when the original connector is damaged, corroded, or loose
• Can stop symptoms like intermittent operation, loss of power to a component, arcing, or related error codes
• Designed to match the OEM shape and terminal arrangement for a direct replacement

• One connector

• Disconnect power (unplug or switch off circuit breaker) before servicing to avoid shock
• Verify the connector matches the original by comparing terminal count, shape, and wire colors before installation
• Inspect mating terminals and wiring for damage; repair or replace harness wires if needed

The Link is an OEM part for LG refrigerators. It serves as an integral connector between the refrigerator door and cabinet, facilitating smooth opening and closing of the door. With durable construction and precise engineering, the link is designed to withstand the rigorous motion of hundreds of door openings without compromising functionality. 

Symptoms of a bad link include:

• Doors that do not close or seal properly 
• Excessive noise or vibration from the door area
• Damage, bending, or breakage of the connecting pieces
• Misalignment impairing proper door operation

Causes can stem from normal wear and tear over many years of use. Replacing a faulty link restores the refrigerator door's designed motion for convenient access to the interior.

This OEM LG part fits seamlessly while extending the product's useful life. This part is also compatible with Kenmore models featuring LG's refrigerator link assembly design.

The Compressor is an OEM component specifically designed for LG refrigerators. Located inside the refrigerator compartment, the compressor pressurizes and circulates refrigerant through the cooling system. Through precisely timed operation, the compressor maintains optimal freshness.

Symptoms of a bad compressor include:  

• Elevated interior temperatures failing to efficiently chill
• Loud buzzing or vibrating noises coming from inside the walls  
• Frost buildup indicating ineffective cooling cycles
• Complete cooling system failure leaving foods unpreserved

Causes involve refrigerant leaks, blocked airflow to the compressor, or simply wear over tens of thousands of hours of use breaking down moving components.

This OEM LG part is also compatible with some refrigerator models from Kenmore and Sears. Replace to restore reliable, long-term temperature control keeping contents at peak freshness.

A small retaining pin used to secure moving parts and keep components aligned for smooth operation. Replacing a worn or broken common pin can stop rattling and restore proper fit between linked parts. What it does:

• Holds or aligns two parts together so they move correctly and stay in position
• Helps prevent rattling, looseness, or parts slipping out of place
• Works as a simple mechanical fastener—no electronics involved

• One common pin

• Disconnect power to the appliance before beginning any service
• Keep track of small parts; lay out components in order to aid reassembly
• May require removal of trim or a hinge/retainer to access the pin—use basic hand tools
• If the pin is difficult to seat, do not force; inspect mating parts for damage

This cabinet roller supports the refrigerator and lets the unit roll in and out of place for cleaning or service. Replace a worn or broken roller to restore smooth movement and help keep the appliance properly positioned.

• Supports the base of the refrigerator and enables rolling movement
• Helps with safe positioning and service access without dragging
• Common failure signs: appliance is hard to move, scraping or rolling noises, a flat-spotted/cracked wheel, or a wheel that won't turn
• Replace when the roller is damaged, seized, or missing

• Disconnect power and shut off water supply; protect flooring before moving the appliance
• With help, pull the refrigerator forward and safely support it to access the roller
• Remove mounting fasteners, install the new roller, and reuse original hardware
• Confirm level and smooth movement before returning the unit to its location

This compressor damper is a vibration-isolating mount that sits between the sealed-system compressor and the chassis. It cushions the compressor to reduce noise, limit vibration transfer, and help keep refrigerant lines from being stressed.

• Isolates the compressor from the frame to absorb start/stop shock and vibration
• Helps reduce humming, rattling, or buzzing from the back/bottom of the appliance
• Replaces a damper that's cracked, flattened, hardened, or missing
• Can help if the compressor rocks or the unit vibrates excessively

• Disconnect power and pull the unit forward for access; remove rear/service panel if present
• Support the compressor to relieve load on the mounts before removing fasteners
• Match orientation; transfer any sleeves/spacers from the old damper to the new one
• Ensure the compressor sits level and that tubing is not strained before restoring power

This fan guide directs airflow inside the appliance to improve cooling efficiency and protect the fan assembly. It replaces a worn or broken guide so the fan blades run without rubbing and airflow stays properly channeled. What it does:

• Channels air from the fan to the correct internal passageways for consistent cooling
• Keeps fan blades centered and prevents contact with surrounding components
• Helps reduce vibration and noise caused by a damaged or loose guide
• Common symptom: noisy fan, blade rubbing, or uneven cooling in the compartment

• One replacement fan guide

• Disconnect power before servicing to avoid shock or injury
• Remove access panels and the fan assembly to reach the guide
• Inspect adjacent fan blades and mounts for damage; replace any worn parts
• Reassemble panels and test operation before returning appliance to service

This drain tray assembly collects and channels defrost and condensation water away from the appliance to prevent interior pooling and leaking. It fits into the appliance base and helps maintain normal drainage during cooling cycles. What it does

• Catches defrost/condensation runoff and directs it to the drain path
• Prevents water from pooling under components or inside the cabinet
• Reduces risk of odors and mildew by keeping drainage contained
• Restores proper drainage when original tray is cracked, warped, or missing

• One drain tray assembly

• Disconnect power before starting any repair
• Remove access panels or shelving as needed to reach the tray; handle panels and edges carefully
• Ensure the tray is seated and aligned to the drain channel and any mounting tabs are engaged
• Inspect associated drain tube and seals; replace if damaged to ensure proper function

This small stopper installs in the refrigerator to limit the travel of a moving component and keep it securely in place. Replacing a broken or missing stopper prevents over-extension and helps maintain smooth, aligned operation.

• Limits the range of motion for a door, bin, or drawer to prevent over-opening or accidental removal
• Helps keep interior components aligned and operating smoothly
• Replace if cracked, missing, or deformed
• Common symptoms: drawer or bin slides out too far, door swings past normal range, or a broken plastic stop is found

• Disconnect power before servicing; remove or support the affected bin/drawer/door
• Note the old stopper's orientation and location before removal
• Transfer and reuse any original screws or clips if applicable
• Snap or fasten the new stopper in place and test for smooth movement

The Drier Assembly is an OEM part for LG refrigerators. This part removes moisture and contaminants from the refrigerant, ensuring the system operates efficiently and effectively. The drier assembly helps maintain the proper function of the compressor and other cooling components, contributing to the longevity and performance of the refrigerator.

Causes of a bad drier assembly can include clogs from debris, wear and tear over time, or contamination from moisture or refrigerant leaks.  

Symptoms of a bad drier assembly include:

• The refrigerator not cooling properly
• Frost or ice buildup on the evaporator coils
• Increased noise from the compressor
• Reduced efficiency and higher energy consumption
• You should replace the drier assembly if it becomes faulty or damaged.

This OEM LG part is also compatible with select Sears/Kenmore models.

This holder is a small mounting bracket used to secure internal components in place, helping keep parts aligned and stable for reliable operation. It provides a direct, OEM-compatible replacement to restore proper fit and function. What it does

• Secures and supports nearby components to prevent shifting or vibration.
• Restores proper alignment where a worn or broken holder causes rattling or loose parts.
• Helps maintain normal operation by keeping assemblies seated correctly.
• Works behind panels or inside assemblies where a dedicated bracket is required.

• One holder/mounting bracket as shown.

• Installation generally requires removing the panel or access cover where the holder is located.
• Use proper fasteners shown in your appliance; replace any damaged screws or clips as needed.
• Disconnect power before servicing electrical appliances to reduce shock risk.

The Refrigerator Control Assembly is an OEM part for LG refrigerators. This component is crucial for managing and regulating the refrigerator's cooling and defrosting cycles. It ensures the proper operation of the refrigerator by controlling the temperature and defrost settings.

Causes of a bad control assembly can include electrical surges, wear and tear over time, or moisture damage. These factors can lead to malfunctioning controls or inconsistent temperature regulation within the refrigerator.

Symptoms of a bad control assembly include:

• Refrigerator not cooling properly
• Unusual noises from the control panel
• Inconsistent temperature readings
• Refrigerator not defrosting automatically

This OEM LG part is also compatible with Sears/Kenmore.

The SWITCH, MAGNET is an OEM part for LG refrigerators. It is a switch designed to function in conjunction with the magnetic door seal, indicating to the refrigerator when the door is open or closed. This allows the refrigerator to regulate temperatures properly based on door positioning. 

Symptoms of a bad switch, magnet can include:

•  Temperature control issues, with the fridge struggling to maintain proper coolness levels
•  The fridge fails to switch to energy-saving modes when the door is closed 
•  Lights not turning on or off correctly when the door is opened or closed

Replace yours today with this genuine OEM LG part to ensure consistent and reliable temperature control. This OEM LG part is also compatible with Sears/Kenmore.

The Dispenser Micro Switch is an OEM part for LG refrigerators. It is a component of the ice and water dispensing system, responsible for activating the dispenser when the lever is pressed. 

Causes of a bad Dispenser Micro Switch can include mechanical wear from frequent use, failure due to moisture or debris affecting the switch’s contacts, or electrical faults that prevent proper signaling.

Symptoms of a bad Dispenser Micro Switch include:

• The dispenser not releasing ice or water when the lever is pressed.
• Continuous dispensing or dripping after the lever is released.
• Intermittent or no response from the dispenser controls.

This OEM LG part is also compatible with Sears/Kenmore.

The Fan Guide Assembly is an OEM component specifically designed for LG refrigerators equipped with rear evaporator fans. This assembly guides proper airflow within the refrigerator compartment.

Symptoms of a bad fan guide assembly include:

• Development of warm or cool spots inside fridge surfaces  
• Excessive frost or moisture buildup at specific locations
• Reduced temperature fluctuation stability 
• Abnormally loud fan operation sounds

Causes of failure can be damage allowing fan blade strikes, cracks reducing structural integrity over time, or accumulation of dust clogging air passages.  

Replace yours today with this genuine OEM LG assembly to maintain optimized cooling throughout storage areas. Smooth, balanced airflow preserves food freshness evenly. This replacement part is compatible with Frigidaire, GE, and Samsung models for factory fit and function. Proper air distribution helps maintain energy efficiency.

Replacement lamp cover that protects and diffuses an appliance's interior light, restoring even illumination and shielding the bulb from spills and contact. Restores proper light output and appearance after a cracked or missing lens. What it does:

• Protects the interior light bulb from food splatter, grease, and accidental contact.
• Diffuses and evens interior illumination to reduce hot spots and glare.
• Replaces cracked, yellowed, or missing lenses that can cause dim, flickering, or exposed-bulb issues.
• Matches the original lamp housing shape and secures with the appliance's existing clips or screws.

• Always disconnect power (unplug appliance or switch off circuit) and allow the bulb to cool before beginning.
• Remove any retaining screws or clips carefully; handle the cover gently to avoid cracking.
• Seat the cover securely in the lamp housing and reinstall original hardware—do not overtighten screws.
• After installation, restore power and verify the light operates and the cover is properly seated.

The Ice Dispenser Door Motor is an OEM part for LG refrigerators. This motor is responsible for the operation of the ice dispenser door, controlling its opening and closing mechanism to allow ice to be dispensed without letting warm air into the freezer. 

Symptoms of a bad Ice Dispenser Door Motor include:

• The dispenser door not opening or closing properly,
• Ice not being dispensed when activated,
• Unusual noises coming from the dispenser mechanism.

Causes of ice dispenser door motor failure can include electrical issues such as shorts or wiring problems, mechanical wear over time, or blockages that strain the motor.

This OEM LG part is also compatible with Sears/Kenmore.

The Magnet Switch is an OEM part for LG refrigerators. It plays an important role in monitoring the position of the refrigerator door. 

The magnet switch works together with a magnet installed in the door gasket to detect when the door is opened or closed. It communicates this information to the control board which uses it to manage temperatures and fan speeds accordingly. 

Causes of a bad magnet switch can include wear and tear over time, physical damage, or failure of internal components. 

Symptoms of a bad magnet switch include:

• Improper cooling and freezing performances 
• Inability to detect when the door is opened
• Erratic temperature fluctuations
• Errors codes relating to door sensors

This genuine OEM LG magnet switch restores the door monitoring functions of your refrigerator. It is also compatible with Sears/Kenmore refrigerator models.

This door switch cover houses and protects the refrigerator/freezer door switch, keeping the switch secure and aligned so the interior light and door-sensing functions work reliably. It's a direct-fit replacement for damaged or cracked covers. What it does:

• Protects the door switch from impacts, spills, and debris that can cause intermittent contacts or failure
• Keeps the switch properly positioned so the interior light turns on/off when the door opens and closes
• Helps ensure consistent door-sensing for control logic that manages defrost and cooling cycles
• Reduces the risk of moisture reaching the electrical switch components

• One door switch cover

• Power off and unplug the appliance before beginning any repair to avoid shock or damage
• Handle gently to avoid breaking the plastic tabs; some models use snap-in tabs or screws for mounting
• Verify switch alignment and operation before fully reassembling the door trim
• Replace the switch assembly as needed

This DC motor assembly replaces the appliance's original drive motor to restore reliable powered movement and control. It offers direct-fit replacement when the existing motor fails, helping stop failures or erratic operation. What it does

• Spins and controls the appliance's driven components using a DC motor drive.
• Restores normal operation when symptoms include failure to start, intermittent running, or loss of power to the driven system.
• Stops or reduces abnormal noises or vibration caused by a worn or damaged motor.
• Works with the appliance's control system to respond to speed and torque commands.

• One DC motor assembly.

• Disconnect power before beginning any repair to avoid shock or injury.
• Installation requires basic hand tools and may require removing panels or brackets for access.
• Keep mounting hardware and wiring orientation the same; reconnect all plugs securely.
• If you see damage to connectors or wiring, replace or repair those before powering the appliance.

This sheath heater is the internal heating element that produces and transfers heat for drying cycles. It restores heating capability so the dryer can evaporate moisture and complete cycles efficiently. What it does

• Heats air inside the dryer drum so clothes can dry.
• Common symptom: dryer runs but produces little or no heat.
• Common symptom: loads take much longer than normal to dry.
• Works with the dryer's thermal sensors and thermostats to maintain temperature.

• One sheath heater

• Disconnect power to the appliance before beginning any repair.
• Allow the unit to cool and access the heater from the rear or lower panel per your model's service manual.
• Inspect wiring and terminal connections for damage; replace any burnt connectors.
• Follow OEM service manual steps and safety guidance.

This LED light assembly illuminates the refrigerator interior when the door opens, delivering bright, efficient lighting so you can easily see items. Replace a failed module to restore proper visibility inside your fridge.

• Provides interior illumination for the fresh food or freezer compartment
• Turns on and off with the door switch
• Helps you quickly find items and check food condition
• Common symptoms: no light when doors open, flickering/strobing, dim or intermittent lighting

• Disconnect power to the refrigerator before servicing
• Remove any lens/cover, release retaining tabs, and unplug the wire harness to remove the old module
• Connect the new assembly, align tabs, and snap/secure it into place; reinstall the cover
• Restore power and verify operation; the door switch activates the light

The Power Cord Assembly is an OEM replacement part for LG refrigerators. It includes both the electrical cord and strain relief connector that links the refrigerator to a standard wall outlet.

This power cord assembly is responsible for safely delivering electricity from the outlet to the control board and components inside the refrigerator compartment. It allows the unit to properly power on and maintain cold interior temperatures.

Symptoms of a bad power cord assembly can include: 

• The refrigerator fails to power on at all
• Electrical humming, buzzes, or burning smells detected  
• Tripped circuit breakers interfering with the operation
• Indicators of cord fatigue such as cracks or frays

Causes may involve normal wear over years of use, improper strain relief, or physical damage. Replacing the cord assembly with this genuine LG OEM part ensures a continued reliable power supply to the unit. It is also compatible with Kenmore refrigerators.

This sub PCB assembly is an electronic control board that processes inputs and switches components, coordinating specific appliance functions. Replacing a failed board can restore normal operation and resolve dead controls, error codes, or intermittent, unpredictable behavior. What it does:

• Distributes and regulates control power and switches loads via onboard relays/triacs
• Interprets signals from sensors and the user interface to execute commands
• Coordinates timing and operation of related components per the appliance's program logic
• Failure may present as no power, won't start, unresponsive or flickering display, random beeps, or recurring error codes

• 1 sub PCB assembly

• Disconnect power to the appliance before servicing; verify no voltage is present
• Use ESD protection and handle the board by the edges
• Photograph wiring; transfer connectors one at a time and ensure they are fully seated
• Secure the board with existing fasteners/standoffs; perform any required reset or diagnostic per your model's service info

This display power control board assembly powers and controls the appliance's user display and touch/buttons so you can see settings and operate the unit reliably. It replaces a damaged or non-working display interface to restore normal control. What it does:

• Supplies power to the front display and user interface circuitry
• Manages button/touch input so commands register correctly
• Drives display indicators and status lights for clear feedback
• Can resolve symptoms like a blank display, unresponsive buttons, or intermittent display behavior

• Disconnect all power before starting work to avoid shock or damage.
• Handle the board by the edges and avoid static discharge; use an anti-static strap if available.
• Verify connector orientation and mating clips before powering up; do not force connectors.

This ice maker lever is the mechanical arm that controls ice production by interacting with the ice maker's on/off and level-sensing mechanism. Replacing a broken or missing lever restores proper operation and helps prevent overfilling or no-ice conditions.

• Acts as the ice maker's shut-off arm to regulate ice production
• Lowers to allow ice making; raises to stop when the bin is full
• Common symptoms: ice maker won't stop making ice, no ice when arm is stuck up, broken/missing lever, lever won't stay in position
• Helps ensure consistent, reliable ice production control

• Disconnect power and shut off water before service
• Remove the ice bin to access the ice maker; gently release the lever from its pivots/linkage
• Note lever orientation; transfer and reuse any original springs, clips, or fasteners
• Reinstall components, restore power, and verify free up/down movement of the arm

This refrigerator ice maker assembly automatically fills, freezes, and harvests ice cubes into the bin. Replacing a failed ice maker restores steady ice production and proper shutoff when the bin is full.

• Automates the ice-making cycle: fills the mold, freezes water, and ejects cubes into the bin
• Monitors bin level and stops production when full
• Helps address symptoms such as no ice production, not cycling/harvesting, or cubes not ejecting
• Can also help with intermittent or inconsistent ice output

• Unplug the refrigerator and shut off the water supply before servicing
• Remove the ice bin, unfasten mounting screws, and disconnect the wire harness
• Transfer existing brackets or covers if required; reconnect harness and secure the assembly
• Align the fill tube with the icemaker inlet; restore power/water and allow up to 24 hours for normal ice production

This ice maker assembly replaces a failed refrigerator ice maker to restore automatic ice production and reliable cube harvesting. Use it to address lack of ice or irregular ice cycling so your appliance makes ice again. What it does:

• Freezes and cycles water into ice, then harvests cubes into the ice bin.
• Common replacement for no ice production, reduced output, or an ice maker that won't cycle.
• Helps isolate ice-maker failures from water-supply or valve issues when diagnosing ice problems.

• Always disconnect power and shut off the water supply before beginning service.
• Some installs require removing shelves, drawers or interior panels.
• Basic hand tools are typically all that's needed; handle electrical connectors and the fill tube carefully.
• If issues continue after replacement, verify water supply pressure and the water inlet valve.

The Auger Motor is an OEM part for LG refrigerators. It is responsible for dispensing ice from the icemaker into the ice bucket. 

Symptoms of a bad auger motor include:

• Slow or incomplete ice filling of the ice bucket
• Ice clumping or jamming in the auger assembly 
• Grinding or rubbing noises coming from the icemaker region
• The icemaker not producing any ice at all

Causes of a bad auger motor can be wear and tear over time, freezing or ice buildup preventing proper operation, or failure of internal motor components. 

This OEM LG part is also compatible with select Sears/Kenmore models. 

The Water Line Connector is an OEM replacement part for LG refrigerators. It is responsible for connecting the water supply line from the home plumbing to the refrigerator's internal water distribution system, allowing for ice and water dispenser functionality. 

Causes of a bad water line connector can include cracking, leaks, or deterioration of the connector material over time due to regular water pressure and temperature fluctuations. Connectors may also become damaged if exposed to impact.

Symptoms of a bad water line connector include:

• Leaks at the connection point between the line and refrigerator
• Loose, slipping, or disconnected water line fitting  
• Reduced water pressure or no water flow to the dispenser
• Error codes related to water flow from the refrigerator diagnostics

 This OEM LG part is also compatible with Sears/Kenmore refrigerators.

The Clip is an OEM part for LG refrigerators. This clip secures the water tube in place, preventing it from moving or becoming disconnected. It plays a crucial role in maintaining the proper flow of water to the ice maker and water dispenser.

Causes of a bad water tube clip can include physical damage, wear and tear from regular use, or brittleness due to temperature fluctuations. If the clip fails, it can result in leaks or disconnections, disrupting the water supply.

Symptoms of a bad water tube clip include:

• Water leaks inside or outside the refrigerator
• The water tube becoming loose or disconnected
• Reduced or no water flow to the ice maker or water dispenser

This OEM LG part is also compatible with Sears/Kenmore refrigerators.

This sensor PCB assembly detects and relays sensor signals to the appliance control system, restoring accurate sensor feedback and communication when the original sensor board fails or malfunctions. Designed as a direct replacement board. What it does:

• Reads sensor inputs and converts them to signals the main control board can interpret.
• Replaces a failed or intermittent sensor board that causes incorrect readings or sensor-related error codes.
• Can resolve symptoms such as unexpected sensor faults, control errors, or appliances not responding to sensor changes.
• Matches the OEM board function; verify model compatibility before ordering.

• Always disconnect power before servicing to avoid shock or shorting the board.
• Use ESD precautions and handle the PCB by its edges to prevent static damage.
• Ensure all connectors are fully seated and the board is mounted in the original orientation.

The Fan Grille Assembly is an OEM part specifically designed for LG refrigerator fan components. It houses the small circulating fan that helps regulate airflow and temperatures within the fridge and freezer compartments.

Causes of failure include normal wear over time of plastic parts, mineral deposits clogging mesh surfaces, or cracks from appliance shipping/handling.

Symptoms of an inadequate fan grille include: 

• Fluctuating temperatures requiring frequent adjustment 
• Foggy freezer glass from warm air infiltration
• Faster ice buildup or frost accumulation
• Reduced shelf life of meats and other perishables

 This OEM part also fits select Sears/Kenmore models.

This assembly stores ice and delivers it from the ice maker to the dispenser. Replace it when the bin is cracked, warped, or its drive components are damaged, causing weak dispensing, jams, or being stuck on one ice type.

• Stores ice and interfaces with the dispenser system to deliver cubes or crushed ice
• Resolves no or weak ice dispensing
• Corrects grinding/clicking noises or auger jamming from a damaged bin
• Addresses visible cracks, broken tabs, or a bucket that won't seat securely

• Disconnect power to the refrigerator before servicing
• Open the door and pull the old bucket straight out; depress any release tab if equipped
• Align and seat the new assembly fully so the drive coupling engages—do not force it
• Restore power and test the dispenser (cube and crush selections)

This does include the Ice maker.

The Ice Dispenser Assembly is an OEM part for LG refrigerators. It incorporates the components responsible for making and dispensing cubed ice. 

Causes of a bad dispenser can include worn gears or drive wheels that no longer advance ice consistently. Clogs or mineral buildup from hard water sediments over time also reduce effectiveness.

Symptoms of a dysfunctional dispenser assembly include:

• Ice cubes dispensing poorly or jamming within the chute
• Grinding or other unusual noises during dispensing
• Dispenser knob or lever functioning intermittently
• Inability to selectively dispense ice or water

This LG part is also compatible with some Kenmore models.

The Water Tank is an OEM part for LG refrigerators. It is responsible for storing and supplying water to the refrigerator's internal dispenser and ice maker. Made from food-grade plastic, the water tank is designed to hold water in a safe, sealed container.

Causes of a bad water tank can include cracks that develop over time, possibly from repeated fillings and drainings of the tank which lead to stress fractures. Mineral or sediment buildup may also cause issues.

Symptoms of a faulty water tank include:

• Leaks or water spillage inside the refrigerator 
• Inconsistent or disrupted water supply to the dispenser/icemaker
• Irritating noises from water sloshing around a damaged tank

This OEM LG part is also compatible with Sears/Kenmore refrigerator models. Proper installation of this replacement part will restore full water functionality.

This water line holder secures and routes the refrigerator's plastic water tube so it stays protected and out of the way. Replacing a damaged holder helps prevent kinks and leaks and keeps water flowing to the dispenser and icemaker.

• Anchors and guides the water tube along the cabinet/door to prevent rubbing and kinking
• Helps maintain proper water flow to the dispenser and ice maker
• Replace if the holder is cracked, missing, or the tube won't stay seated
• Symptoms can include leaks or drips near the hinge/backs, slow or no dispensing, or visibly loose tubing

• Disconnect power and turn off the household water supply before servicing
• Access the holder (often behind a hinge cover, kick plate, or rear panel)
• Note tube routing, then release/remove the old holder and seat the tube in the new holder; reuse existing hardware if present
• Restore water and power; check for leaks and normal dispenser/ice operation

The Connector (Mech), Tube is an OEM part for LG refrigerators. It is used to securely connect water tubing within the refrigerator, ensuring a reliable flow of water to components such as the ice maker and water dispenser.

Causes of a bad connector can include wear and tear over time, physical damage from improper installation or handling, or degradation due to exposure to varying temperatures and water pressure.

Symptoms of a bad connector include:

• Leaks or drips around the connector area
• Reduced water flow to the ice maker or water dispenser
• Water pooling inside or around the refrigerator
• The ice maker or water dispenser not functioning properly

This OEM LG part is also compatible with Sears/Kenmore models.

The Tube is an OEM replacement part for LG refrigerators. It is a 1/4" plastic tubing that transports water from the main supply line to the refrigerator's water dispenser and ice maker. 

Over time, causes of a faulty water line can include mineral buildup restricting water flow, microscopic cracks developing from regular use and pressure fluctuations, or kinks interfering with the flow. 

Symptoms of a problematic water line include:

• Slow or intermittent water flow from the dispenser
• Incomplete fills of ice trays
• strange noises when water is dispensed
• Water leaks underneath or behind the fridge 

This LG part is also compatible with Sears/Kenmore refrigerators.

The Reservoir Water Supply Line is an OEM part for LG refrigerators. This component is essential for delivering water from the reservoir to the dispenser and ice maker, ensuring a steady and reliable flow.

Symptoms of a bad Reservoir Water Supply Line include:

• Leakage of water at connection points or along the line.
• Reduced water flow to the dispenser or ice maker.
• Unusual tastes or odors in the dispensed water.
• Visible signs of wear, such as kinks or brittleness.

Causes of a bad water supply line can include physical damage from bending or pinching, chemical degradation from exposure to contaminants, or blockages due to sediment or scale buildup.

This OEM LG part is also compatible with Sears/Kenmore.

This water inlet valve assembly controls the flow of household water into your refrigerator's ice and water system. Replacing a weak or leaking valve helps restore reliable dispensing and ice production while preventing drips or overfilling. What it does:

• Electrically opens to route water to the dispenser and/or ice maker as commanded by the controls
• Regulates flow and shutoff to maintain proper fill levels
• Typical symptoms include no water from the dispenser, little or no ice, slow fill, or dripping/leaks near the rear of the refrigerator
• Internal coil or seal wear and mineral buildup may cause buzzing, sticking, or constant dripping

• Includes: 1 water inlet valve assembly

• Disconnect power and shut off the household water supply before servicing
• Place a towel to catch residual water; relieve line pressure before disconnecting tubing
• Move tubing and wire connectors to the new valve one at a time to keep orientation correct
• Restore water and power, check all connections for leaks, and purge air by running the dispenser

The Filter assembly,water is an OEM component specifically designed for LG refrigerator water filters. This assembly contains activated carbon blocks that remove impurities from the water supply as it flows through. 

Causes for replacement include normal filter exhaustion from heavy water use, or accidental damage. LG recommends changing the filter every 6 months for optimum performance.

Causes of a bad water filter assembly include:  

• Impurities detected in taste tests of dispensed water
• Slimy or unappealing buildup in water lines or dispenser area  
• Error codes or functionality issues with the dispenser

This OEM LG part is also compatible with select Sears/Kenmore refrigerators.

Restore reliable water delivery with this refrigerator water inlet valve assembly. It regulates flow from your home's water supply to the dispenser and ice maker, providing accurate fills and a positive shutoff to help reduce leaks and drips.

• Opens and closes electronically to direct water to the dispenser and ice maker
• Helps control fill volumes for dispensing and ice tray fills
• Seals closed when not energized to prevent seepage
• Common symptoms of a failing valve: no/low dispenser flow, little or no ice, slow filling, leaks, or dripping after dispensing

• Unplug the refrigerator and turn off the water supply before servicing
• Relieve line pressure by dispensing water; place a towel to catch residual water
• Note wire and tube locations; move connections one at a time to the new valve
• Restore water, check all joints for leaks, flush several cups of water, and discard the first batch of ice

This water inlet valve assembly regulates the flow of household water into your refrigerator. Replacing a sticking or leaking valve restores proper fill for ice production and dispensing and helps stop drips, low flow, and overfill issues.

• Opens and closes to control water flow from the supply line into the refrigerator's water system
• Directs water to the ice maker and dispenser as commanded by the control system
• Seals off when closed to prevent seepage or dispenser drip
• Common failure symptoms: no ice, no or slow dispenser water, leaking at the valve or connections, humming/buzzing from valve with no water flow

• Unplug the refrigerator and shut off the household water supply before servicing
• Pull the unit forward for access; relieve line pressure and place a towel or pan to catch residual water
• Note tubing and wire locations; move them one at a time to the new valve and avoid overtightening fittings
• Restore water and power, check all connections for leaks, and dispense water to purge air from the system

The Water Valve Assembly is an OEM part for LG refrigerators. This assembly controls the supply of water to areas within the refrigerator including the icemaker and water dispenser.

Causes of failure can be mineral buildup over time restricting flow, or damage to solenoid valves and electronic components regulating water pressure and distribution.

Symptoms of a bad water valve assembly include:

• Dripping or flooding from the water line connections
• Inability to dispense water or make ice
• Water levels that fluctuate erratically

This OEM LG part is also compatible with some Kenmore models.

This cover cap is a small plastic trim piece that protects exposed fasteners and improves the appliance's appearance. It snaps into place to hide mounting posts and help prevent snags or debris buildup. What it does:

• Covers and protects exposed screws, posts, or fasteners for a finished look
• Prevents lint, dust, and debris from collecting around the mounting point
• Reduces the chance of fabric snags or contact with sharp edges
• Restores worn or missing trim for improved cosmetics

• Disconnect power to the appliance before starting any service that exposes electrical components
• Usually installs by snapping over the post or press-fitting into the trim opening — no special tools required
• If needed, remove adjacent trim pieces to gain access, then reinstall trim in reverse order
• Inspect surrounding mounting hardware for damage and replace if necessary

This connector tube is a molded inline water connector used on select refrigerators to join water lines and help deliver water to the dispenser or ice maker. It restores a secure path for water flow and helps stop leaks. What it does

• Joins two sections of the refrigerator water line to maintain continuous water flow.
• Creates a sealed connection to prevent dripping or leaking at a damaged or worn joint.
• Helps restore water delivery to the ice maker or dispenser when a broken connector is the cause.
• Compatible with the refrigeration plumbing layout where a short molded connector is required.

• One connector tube as shown.

• Turn off the water supply and unplug the appliance before starting work.
• Inspect tubing ends and fittings; trim damaged tubing and use correct push-fit or compression fittings as required.
• Tighten connections securely but avoid overtightening plastic fittings; check for leaks after restoring water.

The Filter Head Assembly is an OEM component for LG refrigerators. This specialized assembly houses the water inlet valve, filter cartridge, and dispensing head for the built-in water dispenser.     

Symptoms of a failing filter head assembly include:

• Slow or inconsistent water flow from the dispenser  
• Deteriorating water quality or taste over time
• The filter cartridge fails to properly click into place

Causes related to mineral buildup clogging components, worn outlet valves, or damage from freezing over long periods of non-use.

This OEM LG part is also compatible with some Kenmore models for simple, drop-in replacement. 

The Water Filter is an OEM part for LG refrigerators. This filter is designed to remove impurities and contaminants from the water, providing clean and fresh-tasting water and ice. It fits into the water filtration system of the refrigerator, ensuring that the water supplied to the dispenser and ice maker is of high quality.

Common causes of a bad water filter include regular wear and tear, accumulation of sediment and impurities, or damage to the filter housing. Over time, the filter's effectiveness diminishes, requiring replacement to maintain optimal performance.

Symptoms of a bad water filter include:

• Decreased water flow from the dispenser
• Unpleasant taste or odor in the water or ice
• The refrigerator indicating a need for filter replacement
• Visible sediment or discoloration in the water

This OEM LG part is also compatible with Sears/Kenmore.

This pipe holder is a small plastic clip that secures tubing and small pipes inside the appliance, helping keep lines organized and preventing rubbing or disconnection. It restores proper routing and reduces vibration-related noises. What it does:

• Holds and secures water, drain, or refrigerant tubing to prevent sagging and chafing
• Keeps lines routed away from moving parts to reduce wear and noise
• Helps maintain proper tube alignment to avoid strain on fittings
• Commonly replaced when the original clip is cracked, broken, or missing

• Disconnect power and water before working on the appliance
• Inspect surrounding tubing and fittings for damage when replacing the clip
• Typically installs as a push-fit or snap-on clip; use gentle pressure and avoid forcing
• Replace broken or brittle clips to prevent tubing damage or leaks

This is the Home Bar cover — the molded door shelf cover that protects and conceals the refrigerator's door-in-door/home bar compartment for organized storage and a finished appearance. It restores a secure, clean barrier for items stored in the home bar. What it does:

• Replaces a cracked, chipped or missing home-bar/door-in-door shelf cover
• Keeps small bottles and items contained when the home bar is opened and closed
• Restores the proper fit and appearance of the door-in-door/home bar area
• Helps prevent items from falling out of the home bar compartment

• One Home Bar cover

• High-level replacement: usually removes and snaps into the door-in-door shelf housing; some models may require removing the inner door panel or a few fasteners
• Use basic hand tools; keep track of small screws and clips during reassembly
• Inspect surrounding clips and supports; replace any damaged fasteners for a secure fit
• For safety, close the door fully and check smooth opening/closing after install

This lower hinge assembly secures and supports the refrigerator door pivot, restoring proper door alignment and smooth opening/closing. Replace a worn or damaged lower hinge to stop sagging, help seal performance, and reduce rubbing or binding. What it does:

• Provides a stable pivot point for the lower side of the refrigerator door.
• Corrects door sagging or misalignment that can cause poor sealing or uneven gaps.
• Reduces rubbing, scraping, or binding when opening and closing the door.
• Restores proper door operation after impact damage or worn hinge components.