Parts for Maytag MET8720DE03: 04 - Chassis Parts

Positions and supports the side panel for proper alignment and spacing. Replace when the original spacer is cracked, broken, or missing to restore fit.

Replacement screw for electric and gas ranges. Secures internal components and panels. Order a new screw if yours is stripped, missing, or damaged.

Exterior side panel for electric ranges and ovens. Replaces cracked, dented, or discolored side panels. Restores the finished look of your range.

Anti-tip bracket bolts to the floor behind your range to prevent tipping. Replace if missing, bent, or damaged during moving or installation.

Oven won't heat or stops heating during cleaning cycle? The high-limit safety switch cuts power when temperatures exceed safe limits. Moderate DIY fix.

Adjustable leveling leg that stabilizes and balances your range. Replace if cracked, broken, bent, or threads are stripped from wear or impact damage.

Small cushioning bumper that installs on range doors or panels. Replaces worn, cracked, or missing bumpers to reduce noise and ensure quiet closing.

Oven displaying error codes or baking unevenly? The temperature sensor monitors cavity heat and signals the control. Moderate DIY repair in 30-45 minutes.

Replacement mounting screw for securing components and housings in place. Order a new screw if yours is stripped, missing, or damaged during repairs.

This rear cover replaces the dryer's rear panel to protect internal components and restore the unit's enclosure. It helps keep wiring and components shielded while maintaining proper airflow and appliance appearance. What it does:

• Protects internal wiring, terminals and components from dust and damage
• Provides the enclosure for the dryer's rear area and vent connection points
• Reduces rattling and drafts caused by a cracked or missing rear panel
• Helps prevent excess lint accumulation around rear components

• Disconnect power (and gas supply if applicable) before servicing
• Remove the dryer from the wall and lay it on a protected surface to access the rear
• Typical installation requires removing screws and aligning the cover before fastening; use basic hand tools
• Watch for sharp edges and take care not to pinch wiring or hoses during reassembly

This lower vent tube routes exhaust/condensate away from the appliance to maintain proper airflow and drainage. Replacing a damaged vent tube restores correct venting and helps reduce leaks, noises, or performance issues tied to poor airflow. What it does:

• Channels air or condensate from the appliance's venting area to the lower exhaust/drain connection
• Prevents leaks and directs moisture away from internal components
• Helps restore proper airflow and reduces unusual sounds caused by damaged or collapsed tubing
• Used when visible cracks, holes, blockages, or detachment are found in the existing lower vent

• One lower vent tube (single piece as shown)

• Disconnect power and water (if applicable) before starting any repair
• Inspect mating seals and clamps; replace if worn to ensure a secure, leak-free fit
• Handle gently to avoid kinking; route the tube the same way as the original for correct airflow/drainage

Replacement mounting screw for ranges and ovens. Secures panels, brackets, and internal components. Order a new screw if yours is stripped or missing.

Secures and stabilizes internal range components, keeping panels and assemblies properly aligned. Replace when your mounting bracket is broken, bent, or missing.

Replace missing or stripped screws for your range anti-tip bracket. This 2-piece hardware set secures the bracket to the wall or floor for stability.

Light socket assembly houses your oven bulb and provides electrical connections to illuminate the interior. Replace when bulb won't stay secure or light fails.

Oven door won't lock for self-clean cycle? This door lock motor and switch assembly controls locking and detects when the door is shut. Moderate repair.

Seals oven door to prevent heat and smoke leaks for even baking. Replace if worn, torn, or causing heat loss. Includes mounting hooks. Verify fit.

Seals oven door to maintain cooking temperature and improve efficiency. Replace if worn, torn, or heat escapes. Confirm fit with your model number.

Replacement screw for range and oven assemblies. Secures panels, brackets, and internal components. Order if original is stripped, missing, or damaged.

Replacement bracket for electric and gas ranges. Secures and supports internal components. Order a new one if yours is bent, broken, or missing.

Mounting bracket for range installation. Secures and stabilizes your appliance. Replace if bracket is bent, cracked, rusted, or missing hardware.

Burned or damaged terminal block causing power loss? This connection point fixes arcing, sparking, and burnt wire issues. DIY repair with basic tools.

Protective sleeve that routes and shields oven wiring from abrasion and contact. Replace if cracked, worn, or missing to restore safe wiring coverage.

Replaces dim, flickering, or burnt-out bulbs in refrigerators, ovens, and microwaves. Restores interior lighting for visibility. Verify fit with model.

Secures the terminal block to your range's back panel. Replace if stripped, corroded, or missing to ensure safe electrical connections. 10-32 size.

Replacement mounting screw for securing range panels, brackets, and internal components. Replace missing, stripped, or rusted screws to restore fit.

Insulation for range oven doors that prevents heat loss. Replace if the insulation is damaged, torn, compressed, or missing to restore energy efficiency.

Insulation panel for range oven doors. Provides heat retention and energy efficiency. Replace if worn, damaged, or missing to restore proper insulation.

Oven insulation wraps around the cavity to retain heat and improve efficiency. Replace if damaged, compressed, or causing heat loss. Verify fit with your model.

Insulation panel for range oven doors. Installs between door panels to maintain heat efficiency. Replace if torn, compressed, or missing.