Parts for Whirlpool WEG750H0HW2: Chassis Parts

Smoke or odors escaping from your oven? This flue directs exhaust gases safely outside, restoring proper ventilation and consistent baking temperatures.

Replacement mounting spacer for ranges. Maintains proper alignment and clearance between components. Replace if missing, cracked, or worn to restore spacing.

Replacement side panel for your dishwasher. Covers the exterior side of the unit. Order a new panel if yours is dented, scratched, or damaged.

Replacement side panel that restores your range's exterior finish. Covers dents, scratches, or damaged cabinet trim. Easy-to-install cosmetic part.

Fix F8E0 error code or slow cooling fan in your range. This fan motor circulates air for even heating. Moderate DIY repair takes 1-2 hours to install.

Oven light not turning on when door opens? This door-activated switch detects door position and controls interior lighting. Easy push-in installation.

This oven rack replaces a bent, rusty, or missing shelf to restore level support for your cookware. Slides smoothly at the correct cooking height inside your range.

Mounts to the range frame to anchor the door hinge arm. Replace if cracked, bent, or worn to restore proper door alignment and smooth operation.

Adjustable leveling leg installs on the front or rear corners of your range. Replace if broken, cracked, or worn to stabilize and level your appliance.

Replaces cracked, stained, or warped oven bottom panel in gas ranges. Covers burner assembly and provides smooth, cleanable floor surface. Easy install.

Oven not heating to correct temperature or overheating? The temperature sensor monitors and maintains accurate oven temps. DIY repair in 30 minutes.

Replacement mounting screw for securing range panels, brackets, and internal components. Replace missing, stripped, or rusted screws to restore fit.

Wire cover for gas ranges. Protects and conceals internal wiring. Replace if cracked, broken, or missing to maintain proper wire protection.

Replace your gas range's oven flue cover if it's cracked, damaged, or missing. Installs at the rear top of the oven under the cooktop area. Essential part.

Replacement mounting screw for securing range panels, brackets, and internal components. Replace missing, stripped, or rusted screws to restore fit.

Fix uneven heating or burner exposure to spills with this burner baffle shield. Protects burner components and directs heat for consistent cooking.

Mounting screw secures panels, control boards, and burners inside your range. Replace if lost, stripped, or corroded to keep components stable.

This door channel secures the range door glass panel. Replace if the original is cracked, broken, or missing to restore proper door assembly and appearance.

Protects oven cavity components from direct heat and maintains temperature distribution. Replace if damaged, warped, or missing to prevent heat wear.

Replace your burned-out range light bulb to restore interior illumination. Swap in when bulb fails to see contents clearly. Verify fit by model number.

Front leveling foot adjusts range height for stability. Replaces cracked, broken, or missing feet. Ensures proper leveling to reduce vibration.

Structural support base for range drawer rail assembly. Replacement needed when original is cracked, broken, or warped causing misalignment or instability.

Structural support base for range drawer rail assembly. Replacement needed when original is cracked, broken, or warped causing misalignment or instability.

Replace your range's worn or damaged cover. This cover panel protects internal components and provides a finished appearance where installed.

Range door insulation clip secures insulation retainer between inner glass panels. Replace if loose, broken, or missing to maintain door seal integrity.

If your gas range burners won't ignite or click continuously, the spark module may have failed. This repair typically takes 30-45 minutes.

If your gas range burners won't spark or click after a power outage or lightning strike, the spark module often fails. DIY repair in 30 minutes.

This spill guard is a molded trim piece that helps keep food and liquids away from internal surfaces and components, making cleanup easier and protecting parts from corrosion or damage. It installs behind the oven/range area to redirect spills away from sensitive areas. What it does:

• Redirects drips and spills away from internal components and trim to reduce staining and corrosion
• Helps keep hard-to-reach areas cleaner for easier maintenance
• Restores a damaged, cracked or missing guard that can allow liquids to reach electrical or mechanical parts
• Common symptom: visible staining, broken or missing trim, or liquids pooling where the guard should sit

• One spill guard

• Disconnect power to the appliance before starting any repair
• Typically replaces by removing adjacent trim or lifting into place; keep original fasteners
• Inspect surrounding seals and trim; clean mounting area before installing new guard

Replace the air duct in your electric or gas range. This component channels airflow through the appliance and may need replacement if cracked or damaged.

Hidden drip pan that sits beneath the cooktop surface on gas ranges. Replace if cracked, warped, rusted, or discolored from spills and heat exposure.

Insulation panel that lines the oven door to provide thermal protection. Replace if torn, compressed, or missing to restore proper heat retention.

Cable retainer strap for electric and gas ranges. Secures wiring harnesses in place. Replace if cracked, broken, or missing to properly hold cables.

If your oven runs hot or cold or exterior surfaces feel too warm, damaged cavity insulation may be the cause. This thermal barrier restores even heat.

LP orifice kit for gas range bake and broil burners. Includes conversion orifices to switch from natural gas to liquid propane. Replace when missing.