Chipper Shredder Carburetor

This is a genuine OEM replacement float for use in a long list of snow throwers and lawn mowers. A float is a relay component of an engine's fuel tank. As its name suggests, it floats on top of the fuel in the tank, and as the liquid rises, it pushes the float upwards, blocking the float needle to prevent more fuel from entering the chamber. This helps prevent too much fuel from combusting, guaranteeing a balance of air and gasoline in the carburetor. Carburetor floats are generally designed to last the full lifetime of an engine, but they can occasionally wear out and need replacing. When this happens, the carburetor may begin to flood, causing fuel to leak from the engine. This poses a safety hazard and should be repaired as soon as possible. You will need a set of wrenches, socket wrenches, a screwdriver, and pliers to make this repair. This part is compatible with Cub Cadet, MTD, Craftsman, Toro, Tecumseh, and Lawn Boy snow throwers and lawn mowers and comes sourced from the original manufacturer. This is a high-quality replacement part and does not ship with additional hardware.

The primary function of a carburetor is to mix fuel and air in the right ratio. Fuel enters the carburetor through the fuel inlet fitting and then to the float bowl which delivers fuel to the other circuits. From there, the fuel goes to the needle valve, which is actuated by the float. When there is insufficient fuel, the float will stay down, keeping the valve open. Once the chamber has enough fuel, the float will go up and close the valve. A failed float bowl may leak or have too many dirt particles deposits that impede fuel flow. Luckily, you can easily replace a busted float bowl. This part is a genuine OEM Tecumseh 631867 float bowl replacement. You’ll have the assurance that this replacement is manufactured according to Tecumseh’s highest standards. It is compatible with mowers, tractors, and snowblowers from Toro, Cub Cadet, Lawn-Boy, MTD, and Tecumseh. This part is sold individually.

The float shaft and pin are a genuine replacement for select Tecumseh carburetors on small lawn and garden equipment engines. The float shaft and pin are responsible for maintaining the fuel level within the carburetor. Over time because of repetitive motion, the float pin and shaft can break or become damaged, which will stop the carburetor from functioning properly. If the carburetor cannot function, the engine will not be able to perform. If left unattended, the engine and carburetor could fail completely or bigger issues could occur. Replacing the float is essential to getting the equipment back in order. This genuine float shaft and pin is designed for use on machines from Tecumseh, Poulan, Husqvarna, Lawn Boy, Cub Cadet, MTD, and Craftsman, and is compatible with a number of models. The fuel system should be drained and the engine should be cool before any engine repairs are started. Always wear gloves for hand protection. This float shaft and pin are made of durable materials and sold as a unit. No additional hardware or parts are included.

This is a replacement carburetor used with a wide variety of lawn and garden equipment. It includes the full assembly for the carburetor and is responsible for mixing air and fuel together before both are transferred to the engine's combustion chamber. If the carburetor is damaged, the engine may not start as expected, even when the fuel tank is full. Carburetors can also become clogged by dirt or other debris.If the engine is not starting as expected and there is plenty of fuel in the tank, the best thing to do is test the carburetor for problems. This involves adding around a teaspoon of fuel to the carburetor itself after removing the air filter. If the carburetor is the problem, the engine should start but will quickly shut off. A socket set, pliers, and a screwdriver will be needed to replace the part.This carburetor is an authentic OEM replacement part that is directly sourced from the manufacturer. It is sold as an individual product. The carburetor is designed to fit generators and wood chippers created by Briggs & Stratton, Craftsman, Simplicity, and Tecumseh.

This genuine OEM replacement idle restrictor screw regulates how far the throttle cable can travel in lawn mower or snowblower engine. The throttle cable regulates the engine's speed, fuel consumption, and blade or auger turning speed. If the throttle cable travels out too far, the engine will begin guzzling fuel, causing it to run inefficiently. Therefore, manufacturers install this screw to help regulate the throttle cable. The best time to replace an idle restrictor screw is when making repairs to the throttle. These parts are installed together by the manufacturer so they experience similar aging and wear and tear. These screws can become stripped or corrode into their holes. Should this happen, a mechanic will have to pull the screw out and re-drill the hole. For home repairs, use a socket wrench set and a pair of pliers to access the old idle restrictor screw. This screw is a high-quality replacement part for Toro, Husqvarna, and Tecumseh engines. It was sourced from the original manufacturer and ships without any additional hardware.

This is a nozzle tube that is used in the carburetor of many types of lawn and garden equipment. The nozzle tube fits into the primary body of the carburetor bowl and then passes through to the plastic float. The nozzle tube is the component that determines the right amount of fuel that should move into the engine. It is responsible for preventing air leaks and turning oil into a vapor that can be used in lawn and garden equipment.If there is an air leak in the engine of the machine, it could be caused by the nozzle tube. In this case, it needs to be replaced. Depending on how bad the leak is, the equipment could operate at much lower power than normal. Before replacing the nozzle, the tool should be placed on a surface and the spark plug wire should be disconnected.This nozzle tube is an authentic OEM replacement part that is directly sourced from the manufacturer. It is sold as an individual component. Each nozzle tube is designed to fit snowblowers, generators, and wood chippers with small engines from MTD, Cub Cadet, Toro, Briggs & Stratton, Craftsman, and Tecumseh.