Control Board

Oven is a slide in. I pulled it out just a Few inches and removed 8 screws and Pulled the face down to expose the unit. The control unit had 4 screws and 4 Plugins. It only took me less than 10 Minutes to replace unit and slide back In place. Read more

Replace timer; remove lid switch Read more

Took out old timer, and upon inspection notice some electrical arcing( burned areas). I installed new timer and worked perfectly. Problem was that it would fill up with water, but after it was filled the timer kept going but washer was not agitating. Only thing that worked was delicates wash. Important Disconnect/ unplug power cord! 1. Remove knob, center cap pops off revealing a pin. Slide that off and the knob should come off. 2. Removing knob should reveal 2 socket screws remove... Read more

I first tested and replaced the temperature sensor. Since this is a slide-in range, I managed to pull it out just enough to access the back without disconnecting the downdraft and gas line. (For wall models this would not be the case.) Unfortunately, that did not do it. Next I replaced the lower heating element because it was a little below the ohms level it should be at. No go. So far, both of these were pretty easy to do and were relatively inexpensive so I wasn't too frustrated. Then I... Read more

After searching refrigerator videos of related problems I found AppliancePartsPros.com and inquired about replacing the Dispenser Assembly board on the front door. During the several-month malfunction period, the freezer and refrigerator were working before they finally stopped. That lead to a discussion with an APP customer rep who asked me to describe the problem and then reviewed their log of prior customer reviews & Fixit comments with me. We uncovered a description of identical issues in... Read more

Using the model number of the frig, I located the part (Interface Dispenser Asm) on the AppliancePartsPros.com. After reading the Q&A section for hints on how to change the part and looking at a couple of YouTube videos, it seemed that I was up to the task. I placed the order for the part and was pleasantly surprised that it arrived in a couple of days. Armed with a flat blade screwdriver and an old credit card, it took me about 15 minutes to first remove the bezel around the ice dispenser... Read more

I order both boards because everyone said one board did not fix the problem, until they ordered the other board because the new board does not communicate with new one. Well I replaced the board behind where the error was. That seemed to fix the problem. I never changed the main board under the fridge. So I would say try ordering the board behind where error code is. See if that fixes the problem before ordering both boards. Read more

Replaced with part No.AP4417276 electronic control board that we ordered from you and replaced it ourselves with your professional assistance. This has been an excellent experience with your company, and your return policy. Thank you . Read more

Replaced noise filter. Read more

I did an internet search - found your site explaining how to fix. I purchased the upper, middle, and lower spray arms - It took about 15 minutes total. Very very easy. No more dirty dishes! Read more

Replaced new motherboard and face plate. Read more

I contacted Appliance Parts Pros, and told them what the problem was and what it was doing. They sent me an email with the parts number needed to complete the repair. This was a built in a cabinet unit and I required help removing it and reinstalling it. The repair was relative easy once I had the parts and it took approximately four hours,. It took longer getting to the defective parts than replacing them. ... Read more

Easy. Opened the front panel, removed the timer, went on line with the part number. Part arrived the next day and I installed it in 2 minutes. FIXED. Read more

It's very easy fix. If your unit flashing e2 f2. It's your relay board take screw if on door couple latched s on the gray relay box pull wires harness of slow. Re install the same way it came of Just remember to cut the power off first . Leave your door open when re powering unit. Read more

The basin would fill but would not agitate, there was no sound, no grinding noises, no sound of a motor running without agitation due to a broken belt. The basin full of water was able to drain if I advanced the timer to Spin. By playing around with the timer dial further, I could get every function of the washer to operate, at least partially. So, that said electrical problem to me. I assumed the trouble was either the safety switch at the back of the lid or the timer mechanism. Tested... Read more