Parts for Lg DLGX8101V/00: Control Panel Parts

This water tank assembly holds and delivers chilled water to the dispenser and ice system, restoring proper water flow and preventing dispenser dry-running. Direct-fit replacement designed to match the original reservoir's form and function. What it does

• Stores and supplies water for the refrigerator dispenser and ice-making components.
• Replaces cracked or damaged reservoirs that cause leaks or loss of water supply.
• Helps resolve intermittent or no-water dispense when the tank is compromised.
• Works with the refrigerator's fill and drain pathways to maintain correct water levels.

• One water tank assembly

• Disconnect power and shut off the water supply before servicing.
• Drain remaining water from the lines and tank to avoid spills during removal.
• Handle the tank carefully to avoid damaging fittings or mounting tabs.
• After installation, restore water and power, then check connections and test for leaks and proper dispense/ice fill.

The Gas Burner Valve Assembly is an OEM replacement part for LG gas dryers. It is a component located beneath the gas burner that controls the flow of fuel to ignite and maintain the flame. The valve assembly receives ignition and temperature signals from the dryer's control system to precisely regulate gas levels throughout drying cycles. This gas dryer burner valve includes two solenoid coils.

Causes of a faulty gas valve may involve wear over extended operation, mineral buildup on valve seats, or mechanical issues restricting gas flow at desired levels.

Symptoms of a bad gas burner valve assembly consist of:

• Erratic or inconsistent burner ignition between cycles
• Inability to achieve high heat settings when needed
• Burners not maintaining steady flame patterns
• Potential gas leaks detected around valves or tubing

This OEM LG part is also compatible with some Sears/Kenmore dryers.

This Lifter is a replacement shelf support that helps hold and level adjustable refrigerator shelves for smooth raising and lowering. Restores secure shelf positioning so items stay stable and shelves operate correctly. What it does:

• Supports and stabilizes an adjustable refrigerator shelf, preventing sagging.
• Enables smooth lifting and lowering of the shelf when adjusting positions.
• Replaces cracked, broken, or worn plastic support that lets shelves tilt or fall.
• Helps restore proper alignment so refrigerated items sit level.

• One lifter/shelf support.

• Disconnect power to the appliance before starting any repairs.
• Remove the shelf or bin that sits on the lifter to gain access.
• Snap the lifter into the designated mounting slot; some models may require a light push or a screwdriver to assist.

The Pcb Assembly,display is an OEM part for LG dryers. This display PCB assembly serves as the interface between you and your appliance. It provides you with a user-friendly interface to select and control various settings and cycles, ensuring a convenient and efficient drying experience.

A bad display PCB assembly can occur due to electrical issues, component failure, or other internal malfunctions. If you notice symptoms such as the display not lighting up, unresponsive buttons or controls, or error messages appearing on the screen, it may be time to replace the display PCB assembly.

Symptoms of a bad display PCB assembly include:

• Display not lighting up
• Unresponsive buttons or controls
• Error messages appearing on the screen

Restore the function of your LG dryer by replacing the faulty display PCB assembly with this genuine OEM part. This OEM LG part can also be used on Kenmore/Sears appliances. 

The Main PCB Assembly is an OEM replacement part for LG dryers. As the central electronic control center, it oversees functions like temperature selection, timed cycles, sensors that detect moisture levels, and activation of components such as the drum motor, heating element, and fan. 

Causes of a bad main PCB can include exposure to moisture inside the dryer from vent problems or spilled loads. Electrical damage from power surges is also possible. Normal wear contributes to extended use.

Symptoms of a bad main PCB include:

• The dryer failing to power on or start cycles  
• Inability to select the temperature, cycle type, or time settings
• Drum not rotating or heating element not activating
• Abnormal buzzing or humming noises arising  
• Frequent trips of the thermal fuse

It extends the appliance lifespan and is also compatible with Sears/Kenmore dryers.

This poly-V dryer drum drive belt wraps around the drum and pulleys to transfer motor power for tumbling. Replace a stretched, glazed, or broken belt to restore drum rotation and consistent drying performance.

• Transfers motor rotation to the drum for steady, even tumbling
• If broken, the motor may run but the drum won't turn
• Worn or slipping belts can cause squealing, thumping, or a burning rubber smell
• Cracks, frayed ribs, or glazing are visual signs the belt needs replacement

• Disconnect power; for gas dryers, also shut off the gas supply
• Remove top/front panels and support the drum to access the belt path
• Loop the new belt around the drum and route/tension it per the unit's belt diagram with the idler and motor pulleys
• Spin the drum by hand to check tracking before reassembly and test run

The Drum Seal is an OEM part for LG dryers. It forms an airtight seal between the rotating drum and stationary outer housing. This seal prevents air leakage that could diminish drying effectiveness.

Causes of a bad drum seal can include cracks or breaks from heat cycling over time, hardening and failure of rubber seal materials, or physical damage from cleaning tools or debris inside the drum.

Symptoms of a bad drum seal include:

• Slow or incomplete drying times
• Clothes not feeling fully dry at the end of cycles
• Excessively long heating cycles
• Noticeable air drafts around the dryer housing

This OEM LG part is also compatible with some Kenmore models.

This Taptite screw is a factory thread-forming fastener used to secure panels, brackets, and internal components where specified by the manufacturer. It forms threads as it drives for a secure, long-lasting hold when replacing a missing or damaged screw.

• Fastens covers, brackets, and internal parts at the designated mounting points
• Thread-forming "Taptite" design creates mating threads in the receiving hole for a snug fit
• Helps restore alignment and reduce vibration or rattling from loose hardware
• Typical symptoms: loose or misaligned panel/handle, rattles during operation, missing or stripped screw

• Disconnect power (and shut off water/gas if applicable) before servicing
• Replace only in the exact location specified for this part; match head style and length to the original
• Start by hand to avoid cross-threading; if resistance is high, back out and re-start
• Tighten until snug; do not overtighten to prevent stripping or cracking

This Pipe Assembly routes water into the appliance so the dispenser and ice maker can receive a steady supply. Replacing a damaged tube restores proper water flow and helps stop leaks or pooling inside or beneath the unit. What it does:

• Carries incoming water from the household supply to the appliance's internal water system
• Restores water delivery to the dispenser and ice maker when the original tube is cracked or blocked
• Prevents leaks and water damage caused by split, corroded, or pinched tubing
• Helps eliminate intermittent flow or weak dispenser output caused by a damaged water line

• One complete pipe assembly as shown

• Shut off the refrigerator's water supply and unplug the appliance before beginning
• Handle tubing fittings carefully; use proper tools to avoid damage or overtightening
• Inspect connection points and replace seals or clips if worn; test for leaks after reinstalling

The Dryer Ignitor is an OEM part for LG dryers. It is crucial for the ignition process in gas dryers, responsible for lighting the gas burner that provides heat for drying clothes. This ignitor must heat up to a high temperature to ignite the gas, and its proper function is essential for the dryer to operate safely and efficiently.

Symptoms of a bad Dryer Ignitor include:

• The dryer not heating up, even though all other functions are working correctly.
• The gas valve opening but no flame being produced, indicating the ignitor isn't reaching the necessary temperature.
• Intermittent heating, where the dryer sometimes produces heat and other times does not.

Causes of a bad dryer ignitor can include thermal fuse issues, a broken or malfunctioning ignitor due to wear and tear, or electrical problems affecting power delivery to the ignitor.

This OEM LG part is also compatible with Kenmore models.

This Drawer Panel Assembly replaces a worn, cracked, or faded front panel to restore the appliance's appearance and provide a secure drawer face. It matches factory fit and finishes for a clean, finished look on compatible units. What it does:

• Replaces the exterior front face of a drawer, restoring cosmetic appearance and protecting the drawer frame.
• Provides mounting surface and alignment for the drawer closure and trim.
• Helps stop drafts or light leaks caused by damaged or warped panels.
• Common symptom: visible cracking, chipping, discoloration, or loose/warped drawer front.

• Disconnect power to the appliance before starting work and remove stored items from the drawer.
• Basic hand tools are usually required; handle painted or plated surfaces carefully to avoid scratches.
• Follow OEM service instructions for proper alignment and fastener torque; verify clips and brackets are correctly engaged.

For propane order 383EEL3002A.

Replacement door gasket that seals the refrigerator/freezer door to help keep cold air in, reduce energy loss, and maintain consistent temperatures for stored food. What it does

• Forms an airtight seal around the door to prevent warm air from entering the compartment.
• Helps maintain even cooling and prevents frost or ice buildup caused by air leaks.
• Can reduce running time and energy use when the original gasket is torn, warped, or no longer seals.
• Common symptoms of a failing gasket: visible gaps, condensation or frost at the door, uneven temperatures, or increased energy use.

• Disconnect power to the appliance and remove food from affected areas before beginning work.
• Inspect the door frame for dirt or debris and clean mating surfaces before installing the new gasket.
• Align the gasket to the door and seat it fully—follow OEM alignment steps for your model; if the gasket is stiff, warm it slightly per OEM guidance to help fit.

This duct assembly channels dryer exhaust between internal components to ensure proper airflow and help the appliance vent safely. Replacing a damaged duct restores efficient venting and can reduce drying time and heat buildup. What it does:

• Channels heated air and moisture from the drum to the external vent
• Keeps internal airflow pathways sealed to maintain drying efficiency
• Helps prevent hot spots that can cause odors or reduced performance
• Reduces air leaks that can lead to longer dry cycles or moisture buildup

• One duct assembly

• Disconnect power and, if applicable, gas supply before starting work
• Verify correct orientation and seating of seals; fasten with manufacturer-specified hardware
• Inspect adjacent hoses and clamps for wear and replace if needed

This door hinge assembly restores smooth, secure door movement. Worn or bent hinges can cause a misaligned door that won't close or seal properly—replacing the hinge brings back proper alignment and reliable operation.

• Supports the door and provides the pivot point for opening and closing
• Maintains correct alignment so the latch/strike engages properly
• Helps ensure an even seal to prevent leaks or air gaps
• Common symptoms: sagging or rubbing door, difficulty closing or latching, door popping open, squeaking/loose movement

• Disconnect power before service; shut off water supply if applicable to your appliance.
• Support the door to prevent stress on glass and cabinet while removing the hinge.
• Remove mounting screws; transfer any brackets or bushings from the original hinge as designed.
• Align the new hinge, tighten screws evenly, and verify smooth operation and proper latch/seal contact.

This taptite screw fastens panels and internal components in your appliance. It forms its own threads as it's driven to create a secure hold, restoring proper fit and reducing rattles caused by loose or missing fasteners.

• Forms threads in the mating material for a tight, secure fit
• Secures covers, brackets, and assemblies during repair or reassembly
• Replace when the original screw is missing, rusted, stripped, or won't tighten
• Helps address loose or rattling panels and misaligned parts

• Disconnect power before servicing
• Start the screw by hand to avoid cross-threading; use the correct driver
• Do not overtighten; if the receiving hole is damaged, repair or replace the mating component
• Reuse any original washers/spacers in the same order if present

This replacement knob assembly restores tactile control for a range or cooktop control. It provides a secure grip and clear detent positions so you can set burner or surface settings reliably. What it does:

• Replaces a worn, cracked, or missing control knob to regain safe, predictable control
• Engages the shaft and detents so settings stay put during use
• Helps eliminate slipping or difficulty turning the control
• Matches original fit and function for direct replacement

• One knob assembly as shown

• Turn power/gas to the appliance off before servicing; follow appliance manufacturer safety instructions
• Remove the old knob by pulling straight off the control shaft; press the new knob onto the shaft until it seats
• Wear work gloves to protect hands from sharp edges during access

Replacement knob assembly that restores control and precise selection of settings on your appliance. Fits the original control shaft and provides a secure grip for adjusting temperature, cycle, or power settings. What it does

• Restores user control when the original knob is cracked, melted, stripped, loose, or missing.
• Provides a clear indicator/pointer for accurate selection of settings.
• Matches original fit and function to prevent slipping or uneven engagement with the control shaft.
• Helps resolve symptoms like a knob that won't turn, slips on the shaft, or has a broken pointer.

• Always disconnect power to the appliance before servicing; shut off gas supply for gas ranges.
• Typically installs without tools—remove the old knob by pulling it straight off, then press the new knob onto the control shaft.

The High Limit Thermostat is an OEM part for LG dryers, designed to act as a critical safety feature within the appliance. This thermostat monitors the dryer's internal temperature, shutting off the heat source if it detects temperatures that are dangerously high. By doing so, it prevents overheating, which can lead to appliance damage or, in worst-case scenarios, fires. The high limit thermostat is a crucial component for the safe operation of your dryer, ensuring it operates within the specified temperature range.

Causes of a faulty High Limit Thermostat can include a malfunction within the thermostat itself, such as a failure to accurately detect temperature changes, or issues with the dryer that cause it to run hotter than designed, such as restricted airflow or a malfunctioning heating element.

Symptoms of a malfunctioning High Limit Thermostat include:

• The dryer not heating properly or at all
• The dryer repeatedly shutting off during cycles
• Excessive heat emanating from the dryer, indicating it is not regulating temperature correctly

This OEM LG part is also compatible with some Kenmore models.

The LAMP, LED is an OEM component specifically designed for LG dryers. It provides illumination inside the dryer drum, a crucial safety feature for easily viewing clothes during operation. Proper lighting allows users to monitor drying progress without hindering efficiency.

Causes of a bad LED lamp can include regular wear and tear over extended use, as well as potential electrical issues disrupting current flow to the lighting source.

Symptoms of a bad LED lamp include:

• Dim or completely absent lighting inside the dryer drum
• Inability to visually inspect clothes without opening the dryer door
• Premature ending of cycles due to detection of insufficient light  

The high-efficiency LED technology in this OEM part helps maximize useful life. Replace yours today to restore optimal usability. This LG replacement part is also compatible with Sears/Kenmore models.

The High Limit Thermostat is an OEM part for LG dryers, designed to act as a critical safety feature within the appliance. This thermostat monitors the dryer's internal temperature, shutting off the heat source if it detects temperatures that are dangerously high. By doing so, it prevents overheating, which can lead to appliance damage or, in worst-case scenarios, fires. The high limit thermostat is a crucial component for the safe operation of your dryer, ensuring it operates within the specified temperature range.

Causes of a faulty High Limit Thermostat can include a malfunction within the thermostat itself, such as a failure to accurately detect temperature changes, or issues with the dryer that cause it to run hotter than designed, such as restricted airflow or a malfunctioning heating element.

Symptoms of a malfunctioning High Limit Thermostat include:

• The dryer not heating properly or at all
• The dryer repeatedly shutting off during cycles
• Excessive heat emanating from the dryer, indicating it is not regulating temperature correctly

This OEM LG part is also compatible with some Kenmore models.

The Igniter Sensor is an OEM part for LG dryers. This sensor plays a critical role in the ignition process, ensuring that the gas ignites properly to produce the heat necessary for drying clothes efficiently. It helps monitor and regulate the ignition temperature.

Over time, the igniter sensor can become faulty due to regular use, exposure to high temperatures, or electrical issues. These factors can lead to a malfunction, resulting in the dryer not heating properly or failing to start.

Symptoms of a bad igniter sensor include:

• Dryer not heating up
• Long drying times
• Dryer not starting
• Unusual smells or noises during operation

This OEM LG part is also compatible with Sears/Kenmore.

A small mounting bracket that secures and supports internal appliance components to keep shelves, drawers or assemblies aligned and stable. Replaces a cracked, broken or missing supporter to restore proper fit and reduce movement. What it does

• Secures an internal component or assembly in place to prevent sagging or misalignment
• Stops rattling, wobble or looseness caused by a damaged or missing bracket
• Restores correct clearance and support for the associated shelf/drawer/assembly
• Helps maintain normal operation and prevents further wear on adjacent parts

• One supporter holder bracket

• Disconnect power before starting repairs; unplug or flip the appliance breaker
• Remove nearby shelves, drawers or panels to access the damaged bracket
• Inspect mating parts for damage and replace any worn fasteners as needed
• Use basic hand tools;

The Roller Kit is an OEM part for LG dryers. This 4 roller kit includes replacement drum support rollers, which are essential for allowing the dryer drum to rotate smoothly during operation. The rollers are designed to provide stable support for the drum, minimizing noise and ensuring efficient drying performance. 

Over time, drum rollers can wear out due to continuous use, exposure to heavy loads, or lack of proper lubrication. When the rollers become damaged or worn, they may develop flat spots, lose their smooth surface, or begin to squeak. These issues can lead to improper drum rotation or increased strain on other dryer components.

Symptoms of a bad Roller Kit include:  

• Loud squeaking, rumbling, or thumping noises during operation  
• The dryer drum not spinning or rotating unevenly  
• Excessive vibrations while the dryer is running  

This OEM LG part is also compatible with Sears/Kenmore.

This is an authentic OEM drum support roller sourced directly from the manufacturer for use in clothes dryers. During the drying cycle, the drum turns and tosses the clothes around to distribute heat. This drum support roller holds the drum in place as it rotates. Over time, the heat from the dryer can lead to the roller becoming worn. If the dryer is making squealing sounds or thumping when operating, the support roller is worn out and should be replaced. Before replacing the drum support roller, make sure the power is disconnected from the dryer. Remove the top and front panel of the dryer to reach the drum. The idler pulley and dryer belt are underneath the drum; remove these and then take the drum out of the unit and set it aside. Remove the mounting bracket holding the worn drum support roller. Remove and replace the worn roller. While the dryer is apart, inspect the remaining support rollers. Reverse the steps used and put the dryer back together. Power the dryer and make sure the drum turns.This is a black and white, rubber and metal part that is individually sold. It does not come with assembly hardware. This drum support roller is designed for dryers manufactured by LG, Kenmore, and General Electric.

This is a taptite screw used to fasten components to sheet metal or plastic in your appliance. It forms its own threads as it's driven, helping secure panels, brackets, or covers that have lost or stripped fasteners.

• Provides secure fastening in pre-formed or unthreaded holes
• Helps fix loose, rattling, or misaligned panels and covers
• Commonly used for mounting small brackets and internal trim
• Useful when an original screw is missing or stripped

• Unplug the appliance or shut off power and any water supply before service
• Keep track of screw length and location; replace like-for-like
• Start by hand to avoid cross-threading; do not overtighten
• If the original hole is damaged, assess for safe re-use or repair

The Lint Filter Assembly is an OEM part for LG dryers that captures lint and debris from your clothes during the drying cycle. This part maintains the efficiency of your dryer, allows airflow and reduce the risk of overheating. 

Causes of a bad Lint Filter Assembly can include clogging due to accumulation of lint and fabric particles, physical damage such as tears or cracks that allow lint to pass through, and wear over time.

Symptoms of a bad Lint Filter Assembly include:

• Reduced drying efficiency, leading to longer drying times
• Excessive lint and debris outside the filter area
• The dryer overheating due to restricted airflow caused by a clogged or damaged filter
• Unusual smells from trapped lint that may not be effectively captured or is getting past the filter

This OEM LG part is also compatible with some Kenmore models.

This guide cover is a small replacement trim piece that restores proper guiding and protection for the associated assembly, improving part alignment and helping keep debris out of the mechanism. What it does

• Protects and covers the guide area to prevent debris from entering the mechanism
• Helps maintain proper alignment of the adjacent moving parts
• Replaces cracked, broken or missing covers that can cause rubbing or minor noise
• Restores finished appearance to the appliance where the cover is damaged

• One guide cover

• Disconnect power before beginning any repairs; unplug the appliance or shut off the circuit
• Removal typically requires basic hand tools (screwdriver); handle panels gently to avoid breaking clips
• Secure all fasteners and retaining clips until the cover is fully seated
• Inspect adjoining parts and replace as needed

The Locker Assembly is an OEM component specifically designed for LG electric dryers. Found behind the dryer door, this assembly houses door-locking mechanics. 

Causes of a bad locker can include wear and tear over time, damage due to impact, or unintentional stress on components.

Symptoms of a faulty locker assembly include:

• The dryer door not latching securely in the closed position  
• Gaps or air leaks are visible around the door seal when running
• The door is unable to stay shut on its weight  
• Loud clicking or grinding noises from the door area

This OEM LG part is also compatible with some Kenmore models.

This taptite screw fastens panels and internal components in your appliance. It forms its own threads as it's driven to create a secure hold, restoring proper fit and reducing rattles caused by loose or missing fasteners.

• Forms threads in the mating material for a tight, secure fit
• Secures covers, brackets, and assemblies during repair or reassembly
• Replace when the original screw is missing, rusted, stripped, or won't tighten
• Helps address loose or rattling panels and misaligned parts

• Disconnect power before servicing
• Start the screw by hand to avoid cross-threading; use the correct driver
• Do not overtighten; if the receiving hole is damaged, repair or replace the mating component
• Reuse any original washers/spacers in the same order if present

This filter guide secures and positions the refrigerator water filter for proper alignment and a reliable seal. It helps keep the filter stable during normal use so water flows correctly and filtration works as intended. What it does:

• Holds the water filter in the correct position inside the filter housing
• Helps maintain a proper seal to reduce the chance of leaks or bypassed water
• Prevents filter movement or rattling when the refrigerator door is opened
• Supports easy removal and replacement of the filter by guiding insertion

• One filter guide

• Designed to install in the refrigerator filter compartment; follow your model's service instructions
• Turn off water supply and relieve system pressure before removing or installing filter components
• Use basic hand tools as required; avoid overtightening which can damage plastic parts
• Inspect surrounding housing and O-rings for wear and replace if needed

This safety interlock assembly secures the washer door and signals the control when it's safe to run a cycle. Replacing a faulty unit helps restore proper locking and start functions to prevent interruptions and error codes.

• Locks the washer door and confirms it is closed to allow the cycle to start
• Sends door-closed/locked status to the control throughout the cycle
• Helps prevent the door from opening during spin or when water is present
• Common symptoms: won't start, won't lock/unlock, door error (dE) messages, cycle stops mid-wash

• Disconnect power before servicing; wear cut-resistant gloves
• Access the lock at the door opening; remove the mounting screws and disconnect the harness
• Transfer connectors to the new assembly, align, and secure without overtightening
• Ensure the door strike aligns smoothly with the new lock before testing

This distortion spring applies the correct tension within the dryer mechanism so parts return to position and operate smoothly. Replacing a fatigued or broken spring helps prevent loose movement, rattling, and inconsistent operation of the related assembly. What it does

• Provides the designed return/tension force for the associated dryer mechanism
• Helps maintain alignment and smooth movement of moving parts
• Can reduce rattling or squeaking caused by weak or missing spring tension
• Symptoms include components not returning to position or intermittent operation

• One distortion spring

• Disconnect power; for gas dryers, also shut off the gas supply
• Allow internal components to cool before service
• Control the spring during removal/installation—springs are under tension and can snap back
• Note the original spring orientation and attachment points to ensure proper reassembly

Locker hook secures the appliance door or access panel so it stays closed during operation. Replacing a worn or broken hook restores reliable latching and prevents the door from popping open or causing noise. What it does:

• Engages with the catch or striker to hold the door/panel closed during cycles.
• Restores proper door latching and alignment for normal operation.
• Common symptoms: door won't stay closed, rattling or intermittent latching, or door popping open.
• Small replacement part used in the latch area of the cabinet or door assembly.

• Always disconnect power (and water if applicable) before servicing the appliance.
• Access the latch area by opening or removing the door/access panel per the service manual.
• Remove and save any fasteners or clips; install the new hook in the same orientation and secure all fasteners.

This steam nozzle assembly directs a fine spray into the dryer drum during Steam/Refresh cycles. Replacing a clogged or cracked nozzle helps restore proper mist distribution and reduces leaks or drips from the nozzle area.

• Channels water from the inlet line into the drum for steam-enabled cycles
• Maintains the correct spray pattern and coverage
• Common symptoms: no mist/steam, weak or uneven spray, dripping, mineral buildup, or leaks around the nozzle
• Can contribute to wet spots if the spray is misdirected or blocked

• Unplug the dryer and turn off the water supply before servicing
• Allow the appliance to cool; wear gloves and eye protection
• Access is typically near the front bulkhead/drum opening; remove panels as required per model
• Ensure hose seating and clamps are secure; test for leaks after installation

This precision fastener is designed for specific locations on the appliance. Replacing a missing or damaged screw restores secure mounting and reduces vibration or rattling, helping panels and components stay properly aligned.

• Secures brackets, panels, and internal assemblies where this screw is specified
• Replaces stripped, rusted, or lost hardware
• Helps eliminate looseness, vibration, and noise
• Maintains proper fit and alignment of parts

• Disconnect power and shut off water/gas before servicing
• Use the correct driver; keep removed hardware organized for reassembly
• Do not overtighten; install into clean, undamaged threads
• Confirm location and quantity using your model's parts diagram

A replacement refrigerator door hinge that restores proper door alignment and smooth opening. Replaces a worn or broken hinge to stop sagging, binding, or noisy door movement and help the door seal correctly. What it does:

• Provides the pivot point that lets the refrigerator door open and close smoothly
• Restores proper door alignment to prevent gaps that can cause poor sealing or cooling issues
• Stops sagging or binding that can make the door hard to open
• Reduces rattling or clicking caused by a damaged hinge

• Unplug the appliance and empty or support the door before removing the old hinge
• Support the door while installing the new hinge to avoid damage or injury
• Reuse existing mounting hardware only if shown undamaged; replace fasteners if stripped
• After installation, check door alignment and adjust hinge position as needed for a proper seal

This replacement gasket restores a reliable seal between mating parts in your appliance. A fresh seal helps keep air, moisture, and heat where designed, supporting proper performance while reducing leaks, drafts, and rubbing noises from a worn or deformed gasket. What it does:

• Forms a tight, resilient barrier between two surfaces to prevent unwanted air or water escape
• Helps maintain proper airflow, temperature, and/or water containment as designed
• Common signs of failure: visible tears, flattening, fraying, gaps, moisture where it shouldn't be, or unusual scraping/rubbing noises
• Replace if the seal no longer sits evenly, stays in place, or shows noticeable wear

• 1 gasket

• Disconnect power; shut off water or gas supply if applicable. Allow hot components to cool.
• Wear cut-resistant gloves; internal panels and edges can be sharp.
• Access the sealing area per your model's service procedure; remove the old gasket and clean the mating surfaces.
• Seat the new gasket evenly all the way around, then reassemble and check for uniform contact.

Restore reliable steam performance to your washer. This steam generator assembly heats water to create steam for steam-enabled wash cycles, helping improve cleaning and fabric care when the original unit has failed or scaled up.

• Produces steam used during designated steam wash cycles
• A failing unit can cause little/no steam output or cycles to end early when steam is selected
• Replacing the assembly can resolve steam-related performance issues

• Disconnect power and water; allow the appliance and generator to cool completely before service
• Access location varies by model; note wire and hose routing for correct reassembly
• Transfer and secure any hoses/fittings; use proper clamps and check all connections
• After installation, run a steam cycle and inspect for proper operation and leaks

The DC pump motor assembly powers the pump that moves water through your appliance. Replacing a worn motor helps restore proper water flow so cycles can complete and reduces issues like standing water and excessive noise.

• Drives the pump impeller to move water for draining or circulation, as designed by the appliance
• Supports proper cycle completion by clearing water from the tub or sump
• Common symptoms of a failing motor include standing water, incomplete draining/circulation, loud humming or grinding near the pump, or cycle errors
• May run intermittently, stall, or overheat as internal components wear

• Disconnect power and turn off the water supply before servicing
• Expect residual water; protect the area with towels or a shallow pan
• Note wiring connectors and hose routing; transfer any brackets, grommets, or seals from the original as needed
• Secure hose clamps and test for leaks while running a brief test cycle

The Clamp is an OEM part for LG washing machines. It is used to secure the hose connections within the washer, ensuring that water flows correctly without leaks.

Over time, the clamp can become worn or damaged due to repeated exposure to water, vibration, or general wear and tear. If the clamp fails, it can lead to water leaks or hoses becoming detached.

Symptoms of a bad clamp include:

• Water leaking from hose connections
• Hoses coming loose or detaching during operation
• Visible rust or damage on the clamp
• Poor water flow or pressure issues

This OEM LG part is also compatible with Sears/Kenmore models.

The Blower Wheel is an OEM part for LG dryers. This part circulates air through the dryer drum and out the exhaust vent, ensuring proper airflow for efficient drying of clothes.

Causes of a bad blower wheel can include accumulation of lint and debris, wear and tear over time, or physical damage due to foreign objects entering the blower housing.  

Symptoms of a bad blower wheel include:

• Reduced or no airflow from the exhaust vent
• Unusual noises such as rattling or squealing during the drying cycle
• Clothes taking longer to dry or remaining damp
• Overheating or frequent shutdowns of the dryer

This OEM LG part is also compatible with some Kenmore models.

Adapt your gas dryer for propane with this LP conversion kit. It provides the correct orifice and regulator adjustments needed so the burner fires properly on LP fuel, helping ensure safe operation and consistent drying performance after a fuel change.

• Converts a compatible gas dryer from natural gas to liquid propane (LP)
• Helps ensure proper burner flame characteristics on LP
• Appropriate when moving to a home with propane or changing utilities
• Symptoms can include weak heat, improper flame, or sooting

• Disconnect power and shut off gas before servicing
• Installation and regulator/orifice adjustments must be performed per the service manual
• After installation, leak-check all connections and verify proper burner operation
• Do not attempt conversion without the correct kit for your specific model

Blower housing assembly for dryer that channels heated air from the drum to the exhaust. Replaces a cracked or damaged housing to restore proper airflow and help the dryer dry more efficiently and quietly. What it does:

• Channels heated air from the drum to the exhaust and supports the blower wheel.
• Restores airflow when a damaged or cracked housing is restricting ventilation.
• Commonly used to address reduced drying performance and longer dry times.
• Can also resolve unusual rattling or grinding noises coming from the lower front of the dryer.

• Disconnect power (and gas, if applicable) before beginning work; wear eye protection and gloves.
• Remove access panels and disconnect vent/ducting per your model's service instructions to reach the blower housing.
• Inspect the blower wheel and surrounding seals/gaskets while the housing is out; replace damaged components as needed.
• Reassemble all panels and venting securely and test the dryer for proper airflow and operation after installation.

This duct assembly routes exhaust air from the appliance to the external vent, helping maintain proper airflow and preventing leaks. It replaces a damaged or clogged duct to restore effective venting and reduce moisture buildup. What it does:

• Channels hot, moist air from the appliance to the house venting system
• Helps prevent exhaust air leaks that can reduce performance or cause odors
• Can resolve symptoms like longer dry times, damp laundry, or reduced airflow
• Reduces risk of lint buildup in damaged ducts when properly installed

• Disconnect power (and gas supply for gas models) before service to avoid shock or injury
• Use basic hand tools; support the appliance as needed for access
• Inspect adjoining seals and clamps; replace or tighten to ensure an airtight fit
• After installation, run a short test cycle and check for proper airflow and leaks

This guide assembly is a replacement slide guide that helps support and align moving components for smooth operation and reliable engagement. It restores proper tracking and reduces wobble or binding in the mechanism. What it does:

• Provides stable support and alignment for a sliding component to prevent mis-tracking and uneven movement
• Reduces noise, sticking, or binding caused by worn or damaged guides
• Helps maintain proper clearance and engagement of the moving part
• Matches OEM fit and mounting points for direct replacement

• Turn off and unplug the appliance before beginning any repair to avoid electrical shock
• Remove any obstructing panels or components to access the guide
• Inspect mating parts (slides, rails, fasteners) and replace any damaged hardware to ensure correct fit

This adjustable leveling leg screws into the dryer base to support and stabilize the cabinet. Replacing a worn or missing foot helps level the appliance, reduce vibration and noise, and keep it steady on uneven floors.

• Provides threaded height adjustment to properly level the dryer
• Stabilizes the cabinet to minimize rocking, vibration, and walking
• Replaces a broken, worn, or missing foot
• Common symptoms: dryer wobbles, is hard to level, or makes rattling/vibration noise

• Disconnect power; shut off gas supply for gas models
• With a helper, carefully tilt or raise the dryer for access
• Unscrew the old leg; thread the new leg into the base by hand, then adjust with a wrench until the dryer sits level and stable
• Ensure all legs contact the floor and the dryer does not rock

This power cord assembly supplies AC power to the appliance and restores safe operation after a damaged or faulty cord. It replaces the worn or frayed factory cord so the appliance can power on reliably. What it does

• Provides the main AC connection between the appliance and household power
• Replaces cords with visible damage, exposed wiring, burnt connectors, or intermittent power
• Helps stop arcing, sparking, or overheating caused by a failing cord
• Fits into the appliance's cord terminal block for a direct, plug-in power connection

• One power cord assembly

• Disconnect power at the breaker or unplug the appliance before starting any work
• Tighten all terminal screws securely and route the cord away from sharp edges and moving parts

The Dryer Thermistor is an OEM part for LG dryers, designed to monitor and help regulate the temperature within the dryer by providing feedback to the control board about the temperature inside the drum. This allows the dryer to adjust its heat settings accordingly, preventing overheating and ensuring clothes are dried evenly and safely.

Symptoms of a bad Dryer Thermistor include:

• Clothes not drying properly or taking longer than usual to dry.
• The dryer repeatedly stopping during a cycle.
• Error messages appearing on the dryer's display panel.
• The dryer getting too hot or not heating enough.

Causes of a bad Dryer Thermistor can include a buildup of lint and debris affecting its ability to accurately sense temperature, wear and tear over time, or electrical issues within the dryer's circuitry.

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Dryer Blower Thermostat is an OEM replacement part for LG dryers. It plays a role in regulating the operation of the blower motor, which is responsible for circulating hot air throughout the dryer during the drying cycle.

Causes of a bad dryer blower thermostat can include electrical malfunctions, physical damage, or simply wear and tear over time.

Symptoms of a bad dryer blower thermostat include:  

• The dryer not heating up properly or taking longer to dry clothes
• The blower motor failing to turn on or running continuously
• Inconsistent or inadequate airflow during the drying cycle
• Error codes or fault indicators related to the thermostat or blower motor

This OEM LG part is also compatible with Sears/Kenmore models.

This DC motor assembly drives the dryer drum so clothes tumble for even drying and proper airflow. It replaces a worn or failed motor to restore normal drum rotation and dryer operation. What it does

• Spins the dryer drum to enable tumbling and airflow for drying.
• Replaces a motor that causes no-tumble, slow or intermittent drum rotation.
• Stops humming or grinding noises caused by a failing motor or bearings.
• Helps resolve error codes linked to drum drive failures when diagnosed.

• One motor assembly (drum)

• Disconnect power before beginning work to avoid shock or injury.
• Handle the motor carefully; it may be heavy and has delicate wiring and connectors.
• Retain and reconnect all wiring and grounding per OEM routing; verify secure connections before testing.

This clamp secures hoses, tubing or wiring to the appliance frame to help prevent rubbing, vibration and routing issues. It restores a solid attachment point so lines stay in place during normal use. What it does:

• Holds a hose, tubing or wire bundle in place to prevent chafing and abrasion
• Keeps components routed away from moving parts and hot surfaces
• Reduces rattling or vibration caused by loose lines
• Helps maintain safe, reliable connections by preventing strain on fittings

• Disconnect power and shut off water before servicing
• Use basic hand tools; avoid over-tightening which can pinch hoses or wires
• Inspect adjacent hoses/wires for wear and replace if damaged
• Take photos before removal to ensure correct reinstallation

This micro switch is a compact, snap-action electrical switch that sends an on/off signal when a lever, latch, or paddle is moved. Replacing a worn switch restores reliable detection and control response for the affected function.

• Converts mechanical movement into an electrical open/close signal to the control
• Commonly used for lever/paddle actuators, latches, or interlock detection within the appliance
• Safe symptom clues: no response when actuated, intermittent operation, or a function stuck on/off
• Physical clues: weak or absent "click" when pressed, heat discoloration or damage at terminals

• Disconnect power before servicing; if the product is connected to a water line, close the supply valve
• Note wire positions and terminal labels (COM/NO/NC); transfer wires one at a time to matching terminals
• Match the actuator orientation and mounting position to the original for proper operation
• After installation, verify continuity with a multimeter and test function before reassembly

The Idler Pulley Assembly is an OEM part for LG dryers. It plays a critical role in the dryer's drum belt tension system, helping to maintain proper tension on the belt so the drum can rotate smoothly during the drying cycle.

Causes of a bad idler pulley assembly can include wear and tear over time, buildup of lint or debris, or damage from an overloaded dryer. A malfunctioning idler pulley can lead to inefficient drying and potential damage to other dryer components.

Symptoms of a bad idler pulley assembly include:

• Squeaking or squealing noises during operation
• The drum not rotating properly or at all
• The dryer stopping mid-cycle
• The belt slipping or breaking

This OEM LG part is also compatible with Sears/Kenmore.

The Dryer Idler Pulley is an OEM replacement part for LG dryers. It is a critical component that helps guide and maintain proper tension on the dryer belt, ensuring efficient transfer of rotational force from the motor to the dryer drum.

Symptoms of a faulty dryer idler pulley include:

• Squeaking or grinding noises coming from the pulley area
• Visible wear, cracks, or damage to the pulley surface
• Slipping or irregular rotation of the dryer drum

Causes of a bad idler pulley can include normal wear and tear over time, exposure to high temperatures or lint buildup, misalignment or improper tracking, or physical damage from impact or foreign objects.

This OEM LG part is also compatible with Sears/Kenmore dryer models.

This replacement screw secures appliance components in their proper position. Use it to restore a tight, rattle-free fit when the original fastener is missing, stripped, or corroded. What it does:

• Fastens brackets, panels, or trim to keep assemblies aligned and secure
• Helps prevent vibration, rattling, and gaps from loose hardware
• Restores proper attachment when a screw is lost, worn, or damaged
• Common symptoms: loose panel/handle, misalignment, rattling, or a missing screw

• Disconnect power; shut off water or gas before service
• Match location to the original; start threads by hand to avoid cross-threading
• Use the correct driver bit; do not overtighten (especially into plastic)
• If the original hole is stripped, repair threads before installing the new screw

This self-tapping screw fastens panels, brackets, and internal components in compatible appliances. Replace a stripped, corroded, or missing screw to restore a secure fit and help prevent vibration, rattling, and misalignment.

• Forms/engages its own threads in sheet metal or plastic for a secure hold
• Secures covers, brackets, and assemblies to maintain alignment
• Helps reduce vibration and noise from loose components
• Replace if the head is stripped/broken, threads are worn, or the screw is missing

• Disconnect power and shut off water or gas, as applicable, before servicing
• Match to the original location and hardware; use identical length and thread where specified
• Start by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving hole is damaged, repair it before installing the new screw

The Rack is an OEM part for LG dryers. This drying rack attaches securely inside the drum and remains stationary during cycles, allowing delicate items like shoes, sweaters, and hand wash clothes to air dry without tumbling or agitation.

Causes of a bad drying rack can include broken or missing retaining clips, damage to the rack surface that inhibits proper drying, or worn mounting points that cause looseness during operation.

Symptoms of a bad drying rack include:

• Items falling off or sliding around inside the dryer drum
• The rack detaching or becoming dislodged during drying cycles
• An inability to securely hold delicate fabrics and apparel without movement

This LG part is also compatible with some Kenmore models.

The Venting Kit is an OEM part for LG dryers. This part offers flexibility and efficiency in dryer installation and setup, this kit enables side or bottom venting of the appliance, facilitating optimal use of space in your laundry area. It's ideal for situations where the traditional rear venting is not feasible or preferred. 

Causes of venting system issues can include blockages, incorrect installation, or the use of incompatible parts, leading to reduced efficiency and potential safety hazards, such as overheating or fire risks.  

Symptoms of a bad or improperly installed venting system include:

• Extended drying times
• Excessive humidity or heat in the laundry area
• Unusual noises during operation
• Accumulation of lint in and around the dryer

This OEM LG part is also compatible with some Kenmore models.