Parts for Lg LFX28968ST04: Dispenser Parts

The Water Filter is an OEM replacement part for LG refrigerators. It is designed to remove impurities, contaminants, and unwanted particles from the water supply, ensuring that the water dispensed and used for ice making is clean and fresh.

Symptoms of a need to replace the water filter:

• Unpleasant taste or odor in the water or ice
• Decreased water flow from the dispenser
• Discoloration or sediment visible in the dispensed water

Causes of a faulty water filter can include general usage over time, exposure to high levels of contaminants in the water supply, or physical damage or clogging of the filter media.

This OEM LG part is also compatible with some Kenmore refrigerator models.

This holder bracket replaces a damaged or missing mounting support. It secures an internal component so it stays aligned and stable, helping your appliance operate smoothly without looseness or rattling.

• Provides a rigid mounting point to hold a component or assembly in place
• Maintains alignment to reduce vibration, rubbing, and intermittent operation
• Restores support when the original bracket is cracked, warped, or missing
• Common symptoms include a loose/wobbly part, rattling noises, or visible broken tabs

• Disconnect power to the appliance before servicing
• Note the original bracket's orientation and transfer any clips or screws from the old part
• Use existing hardware and tighten fasteners evenly—do not overtighten
• Verify proper fit and alignment before restoring power

This dispenser lever holder is the mounting bracket behind the refrigerator's dispenser paddle. It supports and aligns the lever and switch so water or ice dispenses reliably when the paddle is pressed.

• Holds and guides the dispenser lever and actuator switch inside the dispenser housing
• Provides a secure pivot point for smooth paddle movement
• Helps ensure consistent activation of water and ice dispensing
• Damage can cause a loose or stuck paddle, intermittent dispensing, or no dispense

• Disconnect power and shut off the water supply before servicing
• Remove the dispenser panel/escutcheon to access the lever assembly; note part orientation
• Transfer the lever, switch, and return spring to the new holder and secure with the original fasteners
• Restore power/water and test dispensing before reinstalling trim

The Dispenser Lever Retainer is an OEM part for LG refrigerators. This part secures the dispenser lever in place, this part ensures the smooth operation of the water and ice dispenser. 

Causes of a bad Dispenser Lever Retainer can include normal wear and tear from repeated use, accidental damage, or deterioration of the material over time.  

Symptoms of a bad Dispenser Lever Retainer include:

• The dispenser lever is loose or wobbly
• Difficulty in dispensing water or ice
• The lever does not return to its original position after use
• Unintended activation or difficulty in activating the dispenser

This OEM LG part is also compatible with some Kenmore models.

The Ice Door Lever Spring is an OEM component compatible with LG refrigerators. It is part of the mechanism that opens and closes the ice door on LG French door refrigerators. Over time, springs can lose resiliency or become misaligned.

Causes may be extensive usage over years or damage like kinking that compromises spring function.

Symptoms of a bad ice door lever spring include:

• The ice door not latching fully when closed
• Difficulty opening or poor balance while moving the door
• The lever rubbing or catching instead of moving smoothly

This OEM LG part is also compatible with Sears/Kenmore side-by-side refrigerators.

This display cover is the outer bezel that protects and finishes the appliance control panel, keeping the display and buttons clear while restoring a clean, finished appearance. It helps prevent dirt, spills and damage from reaching the electronics. What it does:

• Replaces a cracked, scratched or discolored control-panel bezel
• Protects the display and button area from moisture, grease and debris
• Restores a snug, finished fit so buttons and indicators align correctly
• Improves appearance when the original bezel is damaged or worn

• Disconnect power before starting any repair to avoid shock or damage
• Remove any trim screws or clips securing the old bezel; retain existing hardware
• Handle the cover carefully to avoid scratching during installation; align clips/screw holes before fastening
• If clips are broken, replace them first — do not force a damaged bezel into place

The Dispenser Cover is an OEM part for LG refrigerators. This cover protects the dispenser unit, shielding the internal components from spills and debris.

Causes for a bad cover can include cracks or breaks from regular opening and closing of the dispenser over time, damage due to accidental impacts, or staining/warping from repeated exposure to liquid spills.

Symptoms of a bad dispenser cover include:

• Presence of moisture, dirt or food particles within the dispenser assembly
• Interior dispenser components becoming corroded or malfunctioning prematurely
• Difficulty opening and closing the cover smoothly
• External cosmetic defects such as cracks, scratches, stains or discoloration

This OEM LG part is also compatible with some Kenmore models.

This plastic lever button transmits your press to an internal switch or latch. Replacing a worn or broken actuator restores crisp, reliable button action so the feature it controls responds as expected.

• Transfers motion from the external button or paddle to an internal microswitch or latch
• Restores positive, consistent actuation and return
• Helps with symptoms like a button that sticks, feels loose, needs extra force, or fails to engage
• Replaces a cracked, worn, or missing lever button

• Disconnect power before servicing; turn off the circuit breaker or unplug the appliance
• Remove trim or the control/escutcheon to access the button mechanism; support tabs and clips to avoid damage
• Note orientation and transfer any springs, pins, or clips from the old part to the new one
• If servicing a microwave, be aware of high voltage stored in the capacitor.

The Actuator Lever is an OEM part for LG refrigerators. It plays a crucial role in the dispensing mechanism of the refrigerator, allowing for the controlled release of water and ice. The lever is designed to interact seamlessly with the internal components of the dispenser to ensure smooth and reliable operation.

Over time, the actuator lever can wear out or become damaged due to frequent use or mishandling. Causes of a bad actuator lever include physical wear, breakage from excessive force, or deformation due to constant usage.

Symptoms of a bad actuator lever include:

• Difficulty in dispensing water or ice
• The lever sticking or not returning to its original position
• Unresponsive dispenser mechanism
• Unusual noises when using the dispenser

This OEM LG part is also compatible with Sears/Kenmore.

This replacement drain tray sits beneath the refrigerator's ice/water dispenser to catch drips and splashes, helping keep the door area clean and dry. It restores a neat, finished look when the original tray is cracked, stained, or missing. What it does:

• Collects drips and minor spills from the dispenser to reduce mess on the door and floor
• Helps prevent water streaks and mineral-stain buildup around the dispenser recess
• Restores a secure, flush fit when the original tray is warped, loose, or broken
• Common signs: standing water in the recess, leaks running down the door, visible cracks, tray won't stay seated

• 1 dispenser drain tray

• Lock dispenser controls or power off the refrigerator to avoid accidental dispensing
• Pull the old tray straight out; clean any residue in the dispenser recess
• Align and press the new tray in until fully seated and flush
• If your model uses a separate top grate, transfer and reinstall it on the new tray

This dispenser drip tray grille sits in the recess beneath the refrigerator water/ice dispenser. It catches drips and splashes, keeping the area tidy while restoring a clean, finished look when the original is damaged or missing.

• Sits over the drain pan beneath the dispenser to catch stray water and ice
• Helps minimize puddling and protects the door finish around the dispenser area
• Restores appearance and fit when the original grille is cracked, warped, loose, or heavily stained
• Direct-fit replacement for the dispenser recess on applicable units

• Disconnect power and avoid using the dispenser during replacement
• Lift the old insert straight up/out; clean the recess before installing
• Align and press the new grille down until fully seated and level
• Verify a secure fit before restoring power and normal use

The Dispenser Switch is an OEM part for LG refrigerators. It is responsible for controlling the operation of the dispenser, allowing you to dispense water or ice from the refrigerator door. This switch is located in the dispenser house and activates the dispenser when pressed.

Causes of a bad dispenser switch can include wear and tear over time, electrical malfunctions, or damage due to accidental mishandling or impact.

Symptoms of a bad dispenser switch include:

• Inability to dispense water or ice when pressing the buttons.
• The dispenser works intermittently. 
• No response or delayed response when pressing the dispenser buttons.

This LG part can also be used on Kenmore/Sears appliances. 

The Ice Dispenser Door Motor is an OEM part for LG refrigerators. This motor is responsible for the operation of the ice dispenser door, controlling its opening and closing mechanism to allow ice to be dispensed without letting warm air into the freezer. 

Symptoms of a bad Ice Dispenser Door Motor include:

• The dispenser door not opening or closing properly,
• Ice not being dispensed when activated,
• Unusual noises coming from the dispenser mechanism.

Causes of ice dispenser door motor failure can include electrical issues such as shorts or wiring problems, mechanical wear over time, or blockages that strain the motor.

This OEM LG part is also compatible with Sears/Kenmore.

This display power control board assembly supplies and regulates power to the appliance display and front-panel controls so the user interface lights up and responds correctly. What it does

• Provides power and signaling to the display and touch/selector controls.
• Replaces a failed or damaged display PCB that causes a dim, blank, or flickering panel.
• Restores responsive front-panel controls when the display or buttons are unresponsive or intermittently fail.
• Helps eliminate display-related errors or communication faults tied to a faulty display board.

• Disconnect power to the appliance before starting; confirm it is fully de-energized.
• Handle the board by the edges and avoid touching components to reduce ESD risk.
• Reconnect all harnesses and connectors to their original positions; verify secure seating before restoring power.

This sub power control board assembly controls and routes electrical power and control signals for the appliance, restoring electronic control when the original sub-PCB fails. Use this board to address power and control-related faults. What it does:

• Regulates and routes power to motors, valves, sensors and other control circuitry.
• Processes low-voltage control signals from the main board, user interface and sensors.
• Common symptoms linked to a failing board: no power or no response, intermittent operation, error codes or unresponsive controls.
• Replacing the faulty sub control board can restore normal electronic operation and command response.

• Disconnect the appliance from power before beginning any service.
• Handle the PCB by the edges and use proper ESD precautions to avoid static damage.
• Verify all connectors are fully seated and wiring matches the replacement before reapplying power.