General Electric Parts

Replaced with no problem. Exact fit. Less than 5 minutes. I will order from your company again. Arrived on scheduled date. Read more

• Element will not heat

Stove is a GE Adora Model JBP63HH2bb. It took me forever to figure out how the burner was attached to the rails. My glass top was different than any instructions found on the internet for changing out a burner. The burners on this one are held to the bottom of the glass cook top by two rails that cross the bottom of the burner assemblies. In order to get too the burners you must remove 4 Phillips screws to lower the rails and burners from the cooktop. I suggest two people do this because... Read more

• Element will not heat
• Won't start

I ORDER THE TERMINAL BLOCK KIT, AND FOLLOW THE VIDEO HOW TO REPAIRE. IT IS VERY EASY.IT TOOK ME 10 MIN. Read more

I replaced the slide bearings a few years back. A few months later the rear bearing started to go so I replaced that one. Bad idea. Replace these two at the same time. The wobbling from the rear bearing failure caused accelerated wear on the slide bearings. Without the money to fix it I ran it as it was. Another bad idea. The drum not only chewed through the slide bearings, but eventually the assembly as well. I replaced the whole assembly and rear bearing at one time a couple days ago. It was... Read more

• Shuts off too soon

After taking the timer apart to see why it would not turn I found the timer motor was jammed. Taking the motor apart I found a broken gear. Looked up the model number of the dryer and found a new timer assembly thru appliancepartspros.com I ordered, a very easy process, received the part 2 days later. Installed the assembly in about 5minutes and had the dryer back up and running Read more

• Will not tumble
• Won't start
• Noisy

My GE dryer from the late 80's/early 90's was squealing when it would start up, belt or bearing I was thinking. I found a manual online that covered my model and I watched a video on this site that showed me how to take it all apart, mine was a bit different but the principles were the same. I took it apart and added some quick-disconnects to 2 wires so next time I can take the front panel off easily. When I got to the bearing it looked worn but not bad so I cleaned it and put it back. ... Read more

I had never worked on a washing machine before but after watching the online videos I felt like I could do the repair. I was almost positive it was the Mode Shifter and Shaft Assembly that was bad. I could hear the bearing making a grinding noise when I turned the tub by hand. I ordered the part I needed plus additional parts that could be an issue later such as a drive belt, tub bearing, tub seal, tub nut, split ring, etc; Preventive maintenance that would keep from having to tear it all... Read more

Just bought the whole assembly and slid it in. Read more

Not the first time my 10 year old dishwasher developed a leak. I have learned that the tub gasket gets dirty and the gasket spring gets weak. Cleaning and if needed replacing that solves the problem. In cleaning the tub gasket this time I notice the bottom door seal had separated from the door. It was originally riveted on. This seal is part of the door assembly and not available as a separate part. You need to buy inner door to get a new seal. Not worth it on a 10 year old appliance. BUT,... Read more

My wife is attached to her old, simple, no bells and whistles dishwasher. When it started leaking from the bottom of the door, I looked up the possible fix and thought the price of the gasket probably out-valued the dishwasher. I thought that it was time to buy a new one. After looking at the prices of dishwashers (even with a Memorial Day sale) I was shocked at high they have gotten. The price of the gasket, which isn't even a third of the price of a bottom of the line DW, was looking even... Read more

• Door latch failure

Replaced the pump drain assembly Read more

• Little to no heat when baking
• Oven not heating evenly

Watched the appliancepartspro video and changed it out. It took about 15 minutes. I'm sure I saved hundreds. Read more

Our refrigerator takes care of my wife and I, along with our children when they visit, and the grand kids. Over the years, it's seen its fair share of wear and tear. Thankfully, nothing major has happened that hasn't been able to be repaired right here in the home, and by me. Our refrigerator is a GE side-by-side with an ice maker/water dispenser, and has held up well. I've ordered parts for it from AppliancePartsPros.com for all of its repairs, and while GE/Frigidaire have been changing out a... Read more

First symptoms were squeaking drum. This is probably when new glide strips might have been all that we needed. But I put off fixing it... and I put it off some more. Noises got louder, squeaking became screeching, then it started to vibrate loudly. The front drum bearing (really just a plastic arch that the drum rides on) had broken, and with the drum in a canted position, the rear bearing sleeve got messed up too. I ordered the front drum support bearing, and also a rear drum bearing... Read more

• Doesn't shut off
• Won't start

Found the part through appliancepartspros.com The part was the cheapest of several web sites. although shipping for such a small part was steep ($7.95 If I was purchasing bigger parts or heavier parts..the flat rate cost would be a bargain. The part arrived the next day and fit perfectly. In additon; obviously the original manufactured part was not holding up well as the new part had a metal reinforcement band that will prevent the cracking in the future. Read more

Replaced hose with new one from Appliance Parts. Delivery was exceptionally fast. Appliance was up and running next day. Read more