Parts for Ge JVM6175DF1BB: Oven Cavity Parts

Replace your microwave's bottom base panel if cracked, rusted, or damaged. This structural part forms the lower cabinet foundation and mounting surface.

Holds the light bulb securely in your microwave for proper interior illumination. Replace if bulb won't stay in place, socket is burned or cracked.

Illuminates your microwave interior for monitoring food during cooking. Replace when bulb burns out or dims. Verify fit with your model number before ordering.

Lamp bracket for microwave interior lighting assembly. Secures the bulb housing in place. Replace if bracket is cracked, broken, or missing.

Replacement glass lens cover for microwave interior or cooktop lights. Protects bulb from food splatters. Needed when cracked, broken, or shattered.

Clear glass lens cover for over-the-range microwave cooktop light. Shields bulb from grease and splatters. Replace if cracked, broken, or missing.

Secures power cord where it passes through cabinet, preventing loose connections that cause intermittent power or sparks. Protects wires from abrasion.

Base plate assembly for over-the-range microwaves. Provides structural mounting support. Replace if cracked, broken, or missing during installation.

Fixes microwaves with no power or that stop mid-cycle. This thermostat switch monitors temperature and protects against overheating. Simple repair.

Microwave won't heat or power on? This bottom thermal cut-off protects against overheating by cutting power when excess heat is detected. Easy fix.

Microwave runs but won't heat food? This high-voltage transformer powers the magnetron to generate heat. Restores cooking function when failed.

This condenser fan motor circulates air across the condenser coils to help the refrigerator release heat and run efficiently. Replacing a worn motor restores proper airflow and can improve cooling performance. What it does:

• Spins the condenser fan blade to expel heat from the condenser coils
• Helps maintain correct compressor and system temperatures
• Runs continuously or with the compressor depending on the model
• Common symptoms: refrigerator running hot, poor cooling, loud or grinding noises from the rear, or fan not spinning

• One condenser fan motor

• Disconnect power to the appliance before servicing to avoid electrical shock
• Typical installation requires basic hand tools and access to rear or bottom rear panel
• If the fan blade is damaged or obstructed, replace or clear obstructions while motor is removed

If your microwave isn't venting properly or makes unusual noise, the blower wheel may be damaged. This fan blade circulates air through the ventilation system.

This spring blade is a small metal tension spring that restores proper tension and movement in the appliance's linkage or latch assembly. It replaces worn or broken blades to help restore normal door or component action. What it does:

• Provides tension and return force in linkage, latch or lever assemblies
• Helps stop sagging, slipping or loose movement in the affected mechanism
• Can reduce related rattling or binding caused by a worn spring blade
• Restores reliable engagement where a broken or fatigued blade allowed failure

• Unplug the appliance or shut off power before starting any repair
• Verify orientation and engagement of the blade before final assembly
• Use proper hand tools; the blade may be under tension—wear safety goggles and gloves
• If the assembly uses multiple springs, replace all worn parts to ensure balanced function

Microwave not working or displays flickering? This wire harness restores electrical connections between control and components. Moderate DIY repair.

Secures the temperature sensor in your microwave. Replace if sensor is loose, misaligned, or causing erratic heating. Confirm fit with your model number.

Fix sensor cook cycles that won't adjust properly or show sensor errors. This humidity sensor monitors moisture levels for automatic cooking adjustments.

If your microwave heats unevenly or has hot and cold spots, a damaged stirrer blade is often the cause. This part distributes microwaves for even cooking.

Stirrer blade holder for microwave ovens. Mounts inside the cavity to secure the waveguide stirrer fan. Replace if cracked, broken, or missing.

Plastic cover that shields the stirrer assembly inside your microwave. Replace if cracked, melted, broken, or missing to protect internal components.

Replacement mounting clip for microwaves. Secures components and panels in place. Order a new clip if yours is broken, cracked, or missing.

Replacement control panel cover for microwave ovens. Restores the front console's appearance and protects controls from spills. Needed when cracked or broken.

Connects the turntable motor to the glass tray in your microwave. Replace if cracked, broken, or worn to restore smooth rotation and prevent slipping.

Microwave turntable not turning? The turntable motor rotates the glass tray for even heating. Simple DIY repair with basic tools in under an hour.

Replacement door latch body for microwaves. Secures the door closed during operation. Install when original latch is cracked, broken, or won't hold door.

Microwave won't stop running or starts when door closes? A faulty door switch is likely the cause. This safety switch is a 45-minute DIY fix.

Microwave won't start or heat but light works and timer counts down? A faulty monitor switch is often the cause. DIY repair typically under 30 minutes.

Replacement door latch lever bracket for microwaves. Installs behind the control panel to hold interlock switches. Needed when bracket is cracked or broken.

Fix a microwave with no power. This thermal cutoff cavity (TCO) safety device prevents overheating by cutting power when temps exceed safe limits.

Fixes microwaves with motors that start slowly or make abnormal noise. This run capacitor stores electrical energy to help motors start and run smoothly.

Fix a microwave that won't heat or hums but doesn't start. This capacitor stores energy for the high-voltage circuit. Moderate DIY repair, 30-60 minutes.

Mounting bracket for microwave ovens. Secures the unit to the wall or cabinet. Replace if bent, broken, or missing during installation or repair.

Microwave not heating but lights and timer work? The high voltage diode converts AC to DC for the magnetron. DIY repair in 1-2 hours with basic tools.

Wire holder clip secures internal wiring in your microwave. Replace if wires are loose or rattling. Verify fit with your model number before ordering.

Microwave not heating evenly or overheating? This thermostat with bracket senses and regulates internal temperature to restore proper heating cycles.

Microwave not heating? The magnetron generates the microwaves that heat food. Common repair for units that run but don't warm. DIY-friendly repair.

Direct replacement noise filter assembly for microwaves. Reduces electrical interference. Replace if cracked, damaged, or missing to restore clean power.

Power cord assembly for microwave ovens. Supplies electrical connection from wall outlet to unit. Replace if cord is frayed, damaged, or missing.

Outer door panel for your microwave. Replaces chipped, cracked, or damaged exterior door frames. Restores clean appearance and door structure.

Secures microwave to wall cabinet mounting bracket. Replace if cracked, stripped, or missing to restore proper cabinet installation and stability.

Fix poor venting or back-drafts in your over-the-range microwave with this hood damper assembly. Opens for exhaust airflow, closes to block drafts.

Rear wall mounting plate bracket that supports over-the-range microwaves during installation. Replace if bent, broken, or missing for secure wall mount.

Wire harness for microwaves. Connects internal electrical components. Replace if wires are frayed, damaged, or connections are loose or broken.

Supports and guides the microwave turntable ring for smooth rotation. Replace if cracked, broken, or wheels keep falling off causing alignment issues.

Glass turntable tray rotates food for even heating in your microwave. Replace if cracked, broken, or chipped from accidental drops or impacts.

Filters cooking odors, smoke, and grease from over-the-range microwaves. Replace when filter light activates or every 6-12 months. Confirm fit with model.

Traps grease, smoke, and odors from your microwave's ventilation system. Replace when clogged or damaged. Verify fit with your model number.

Secures microwave components and mounting brackets. Replace this hardware assembly if screws are stripped, bolts are missing, or fasteners are damaged.

Replaces a cracked, broken, or discolored microwave vent grille. This exterior cover installs over the ventilation opening on your over-the-range unit.

Replaces a damaged or missing spacer on your microwave oven rack. Keeps wires properly separated for smooth sliding and stable support. Snap-in design.