Kenmore Washer 110.47086602 (11047086602, 110 47086602) Parts

Touch up paint Read more

Ordered the striker latch, it arrieved in two days, I removed the two screws holding the broken latch and installed the new latch, then put the two screws back in. Wam Bam, it was fixed, it was easy. Read more

Prior to ordering parts I had pulled the pump strainer basket and cleaned it out. There was both soft and hard scale build up. The tub-to-pump hose was also pretty crusty/slimey. Still got warnings for SUDS and repeated F02 errors. Ordered parts and replaced the pump, tub-to-pump hose, interior drain hose and exterior drain hose (both hoses has some slime build up). The water standing in the tub when I emptied it the first time had very little suds but we kept getting the SUDS warning. ... Read more

• Won't start

Replace the water temperature sensor and still had the error code. While I had the back of the machine open I ran the washer. I traced the black wires from the temperature sensor and wiggled them as the washer was running. At one zip tie every time i moved the wires the washer would stop running and the error code would flash. Sure enough, like many others posted, the vibration from the machine had split the wire. I spiced the wire back together and have not had a problem since. Read more

Several months back, I checked the supply hoses and replaced the hot water hose because of corrosion. The cold water hose was fine. I replaced the water inlet valve and that seemed to fix the problem, but after about a week, the problem resurfaced. After searching various internet resources, I though the pressure switch which detects the water level could be bad. I order both the pressure switch and the hose that connects it to the air chamber. Before installing the new pressure switch, I... Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

• Leaking

We ordered parts from appliance parts pros and I fixed it. Read more

I pulled the unit away from the wall and noticed black dust on the floor. Unplugged the unit, turned off the water. Removed back panel (about 10 screws with Torx heads) and noticed the belt was off, the drive pulley was loose and wobbling on the shaft, black dust all over the inside. Belt was worn along one side. Some grooves/damage in the outer drum casing around the pulley where it appeared the belt had rubbed. Removed the lower crossbar (2 more screws) to get better access to the drive... Read more

I called parts pro and they had my part and sent it right to me I am soooooooo happy with this company they are amazing. I only ordered 1 baffle and now I'm calling them to order the other 2 baffles. Thank you so much for your help and service. Read more

I ordered the dispenser and the distribution nozzle since the old one was in bad shape. I also replaced the boot since I had to take the entire machine apart and it is 20 years old. I watched your videos on you tune to learn what to do. I recently lost my job and really could not afford to hire someone to fix my washer. I have to say it wasn't that hard to do and my wife was so happy that I was able to fix it myself! I probably saved $200 or $300 in service calls and labor on top of what they... Read more

After much reading on line regarding my problem. I decided to do any test that I could to try to diagnose and fix this myself if I could. This took a lot of time and patience to get the answers on how to go about this from "experts" as some of the info was contradictory. I was almost about to give up and buy a new washer with less electronic parts and buttons as advised by an honest appliance technician . I tried one more thing first which was to disconnect the lead wires connected to the MCU .... Read more

Removed the leaking hoses and seal. Installed the new ones. They all fit perfectly. The disassembly/reassembly of the washer took the most time. Read more

Replaced flow meter and control valve Read more

Prior to ordering parts I had pulled the pump strainer basket and cleaned it out. There was both soft and hard scale build up. The tub-to-pump hose was also pretty crusty/slimey. Still got warnings for SUDS and repeated F02 errors. Ordered parts and replaced the pump, tub-to-pump hose, interior drain hose and exterior drain hose (both hoses has some slime build up). The water standing in the tub when I emptied it the first time had very little suds but we kept getting the SUDS warning. ... Read more

The replaced hose from the dispenser and o-ring problem fixed. Read more

The shipping bolts came in 2 days!!! Wow ! So we watched a video on how to install them and moved the washer without messing it up.. Thank you so much for fast and friendly service :-) Read more