Kenmore Washer 110.81476230 (11081476230, 110 81476230) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9724509
These lid bumpers are sold individually.
Do-It-Yourself Stories from Customers like You
Water pump after 18 years wore thru the pvc housing causing a pin hole leak James B. • Palomar Mountain , CA • April 13, 2014
Found AppliancePartsPros on-line. Sent us the manual, parts list, etc. via .pdf files. Our local guy did not. Had parts in stock, two day shipping, totally painless. The parts were approximately 1/2 the price the local guy wanted. OEM parts. Perfect fit on replacement. The Whirlpool is so well made, it was very easy to repair. It has several items, over the years, which failed. In all cases, repair was painless with a few common hand tools and a tad of patience. AppliancePartsPros had...
Read more
More
$8.36
- Compare At:
-
$10.03
- You Save:
-
$1.67
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62780
Used to lock washer cabinet to rear wall of washer.
Do-It-Yourself Stories from Customers like You
Slightly imbalanced load in the washer created a a lot of noise. Marvin F. • Williamsburg , VA • March 13, 2014
Replaced springs and the ordered clips holding the control panel to the washer outer cabinet. Clips had been elongated from earlier repair work. A DIY tutorial was a great help.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP21258
The lid hinge bearing is used for the lid hinges on washers and dryers. When functioning properly, it allows the lid to open and close properly. If this is a problem with the bearing, it could make the lid difficult to move. In some cases, when the lid will not close, it means that the machine will not function correctly. Damaged lid hinge bearings should be replaced as soon as possible.The lid hinge bearings see a lot of work since they are in use whenever the lid of the washer or dryer opens and closes. They could become cracked and broken over time. Replacing the bearings is a relatively simple repair that owners can make on their own.This lid hinge bearing is for use with many models of washers and dryers from Whirlpool, KitchenAid, Roper, Estate, Inglis, Maytag, Admiral, Amana, Crosley, and Magic Chef. This is a genuine OEM replacement part that has been sourced from the manufacturer. The piece is sold individually, so if owners need to replace more than one hinge, they will need to buy multiples.
Do-It-Yourself Stories from Customers like You
Whirlpool washer David L. • Linn , MO • August 31, 2015
With the parts supplied from your company. The lady that took my order was good at her job. All the parts were correct and fit. I thank you for the service that recieved.
Read more
More
$11.95
- Compare At:
-
$13.33
- You Save:
-
$1.38
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62750
The Whirlpool spacer is an OEM replacement part responsible for maintaining the proper spacing and alignment between the washer cabinet and the top panel. The spacer provides stability and support to the appliance. It ensures that the top panel is securely attached and evenly distributed, preventing any misalignment or instability during operation.
Causes of a bad spacer can include wear and tear over time, physical damage due to accidental impacts, or deformation from prolonged use under stress. These issues can lead to misalignment and operational inefficiencies in the appliance.
Symptoms of a bad spacer include:
- Misalignment of components
- Unusual noises during operation
- Difficulty in assembling or disassembling parts
- Reduced efficiency of the appliance
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Sold individually, four are needed to replace all parts. Screw part number WP3390631.
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8519200
This rear panel support is the structural bracket that secures the appliance's rear cover/backguard in place. Replacing a worn or broken support restores proper alignment, helps protect internal components, and reduces vibration noise.
- Secures the rear panel/backguard to the chassis for stable, proper fit
- Maintains alignment of panels and mounting points
- Helps minimize vibration, flexing, and rattles from a loose rear panel
- Common signs of failure: cracked or missing bracket, stripped mounting points, panel movement or buzzing
What's included: 1 rear panel support Install notes:
- Disconnect power at the breaker; shut off gas supply
- Pull the appliance forward carefully to access the back; protect flooring
- Remove fasteners, replace the damaged support, and reuse original hardware/clips
- Keep wiring clear of sharp edges; tighten screws evenly without over-torquing and check for vibration before repositioning
Do-It-Yourself Stories from Customers like You
No spin/agitate. Daniel S. • Landenberg , PA • November 11, 2022
In the end, with a new coupler. But I relearned old lessons the hard way.
The washer is in a rental unit and the tenant complained of no spin. My first intuition was that the coupler failed again because I bought a cheaper one elsewhere a couple of years ago and not the brand name available here at AppliancePartsPros. But we’ll come back to that. Lesson #1: Verify the symptoms firsthand. I dug in right away, popped out the motor and the coupler appeared okay. When I spun it by hand, it turned...
Read more
More
$12.40
- Compare At:
-
$14.63
- You Save:
-
$2.23
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3390631
10 - 16 x 1/2
Do-It-Yourself Stories from Customers like You
Agitator wasnt sloshing Paige B. • Clarksville , TN • January 30, 2015
I looked inside and saw the teeth were worn off the "dogs" so I purchased the Cam Agitator repair kit and a new bolt. Getting the old bolt out was the hardest part since it was worn and rusted. I ended up having to buy a set of socket extensions and a set of stripped bolt sockets so $45 in tools and it took me an hour to get the old bolt out but putting everything back together was a breeze. I was very proud of myself, as a woman, that I fixed this problem myself and didnt have to pay a repair...
Read more
More
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3347034
This vacuum break is the washer's water-inlet anti-siphon fitting. It maintains a required air gap so the tub fills properly without drawing used water back into the supply, helping prevent leaks and backflow issues.
- Maintains an air gap at the inlet to prevent backflow/siphoning into household water lines
- Helps ensure consistent, unobstructed water flow into the tub
- Replaces a cracked, clogged, or leaking vacuum break at the fill area
- Common symptoms include leaks from the rear/top during fill, visible cracks, or restricted/noisy fill
What's included: One vacuum break. Installation notes:
- Unplug the appliance and shut off both water supplies before servicing
- Access the fill/inlet area; note hose routing and part orientation
- Remove hose clamps/hoses and the old vacuum break; install the new part and secure clamps
- Restore water and power, then run a fill test and check carefully for leaks
Do-It-Yourself Stories from Customers like You
Wife noticed water on the laundry room floor! Richard L. • Phelps , NY • April 06, 2015
Removed cover from Whirlpool washer (~20 years old) and found water to be leaking from hose connection at Break Vac. Obviously the hose had to be replaced but the Break Vac looked corroded and partially plugged, too, possibly inhibiting water flow. While the cabinet was off I noticed the Suspension Spring was rusted off so I ordered 1 of those, too. Total of all parts was under $45 so looks like we won't be getting a newer, more efficient washer anytime soon. Everything arrived in 3 days and...
Read more
More
$45.95
- Compare At:
-
$54.68
- You Save:
-
$8.73
Genuine Whirlpool part
By: Whirlpool
Part Number: WP681414
Specs: 10-16 x 1/2 inch.
Do-It-Yourself Stories from Customers like You
Dryer drum was beginning to stall occasionally Dana J E. • San Marcos , CA • March 17, 2015
After shopping for a new Whirlpool Thin Twin Stack, Found appliance parts pros online and decided to take it apart to see if repair was a possibility. APPro's online instructions were easy to follow, in a couple hours it was apart, and I placed the order. Reg ground took a week from NY, so the laundry piled up that week. The parts arrived on Monday morrning, by afternoon the machine was running like new! The cause was the belt tensioner pulley had frozen. Replaced it, drum wheels,snap...
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP96160
This adapter tube assembly connects sections of the appliance's water line to create a secure, leak-resistant path for water flow. Replace it if the tube is cracked or the connection no longer seals properly to prevent leaks and restore flow.
- Connects water tubing between components within the appliance's water system
- Helps maintain a tight, leak-resistant seal at the joint
- Restores proper water flow when a tube or connector is damaged
- Typical symptoms: water leaking at the connection, reduced or no water flow, visible cracks/kinks, loose fit
What's included: One adapter tube assembly. Install notes:
- Disconnect power and shut off the water supply before servicing
- Relieve line pressure and place a towel or pan to catch any residual water
- Note routing and orientation before removal to ensure correct reassembly
- After installation, restore water and check all connections for leaks
Do-It-Yourself Stories from Customers like You
Washer not filling with cold water Stephen S. • Bronx , NY • July 24, 2016
Ordered a replacement valve and installed it. The part from AppliancePartsPro was an exact replacement for the original part. Replaced the hot and cold hoses at the same time to insure no leaks.
Cold water settings now work properly again.
Read more
More
$11.95
- Compare At:
-
$14.22
- You Save:
-
$2.27
Genuine Whirlpool part
By: Whirlpool
Part Number: W10820044
This is a replacement power cord that supplies electrical power from a wall outlet to your appliance. A fresh cord helps ensure safe, reliable power delivery when the original is damaged, overheated, or worn.
- Delivers household power to the unit's main electrical connection
- Replace if the cord is cut, cracked, burnt, loose, or intermittently powers the appliance
- Helps resolve issues like no power, tripping breakers, or visible cord damage
What's included: Power cord assembly with strain relief Install notes:
- Unplug the appliance and turn off the circuit breaker before starting
- Verify outlet type and cord routing match your original installation
- Transfer any cord clamp/retainer as needed and secure against sharp edges
- Inspect for proper grounding and test operation before returning to service
Do-It-Yourself Stories from Customers like You
Power cord got pinched and shorted out Gary D. • Kentwood , MI • July 27, 2014
Bought a new cord and removed the back of the washer and unclipped the old and clipped in the new. 5 minutes tops.
Read more
More
$73.95
- Compare At:
-
$88.74
- You Save:
-
$14.79
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3348552
This internal pump-to-drain hose routes water from the drain pump to the outlet, helping prevent leaks and ensuring proper draining. Replace a cracked or clogged hose to restore reliable, mess-free operation.
- Connects the pump outlet to the machine's drain/outlet port to carry wastewater out during the drain cycle
- Maintains a sealed path to help prevent internal leaks
- Common symptoms of failure: water on the floor, slow or incomplete draining, visible splits or soft spots on the hose
- Replacing a restricted hose can reduce drain pump strain and noise
What's included: 1 pump-to-drain hose Install notes:
- Disconnect power and shut off water supply; remove standing water from the tub if needed
- Access the drain pump and hose by removing the cabinet/front or rear panel per your model
- Release hose clamps, remove the old hose, and seat the new hose fully on both fittings; reuse clamps if in good condition
- Route the hose as originally to avoid kinks; run a drain cycle and check for leaks
Do-It-Yourself Stories from Customers like You
Leaking hose from pump to drain Harold C. • Waynesboro , VA • November 23, 2014
Replaced both inlet and outlet side of pump hoses. Removing the machine cover was the most difficult part of the entire project, and it was not hard at all after watching your "How to" videos.
Thanks for excellent service.
Read more
More
$51.95
- Compare At:
-
$61.82
- You Save:
-
$9.87
Genuine Whirlpool part
By: Whirlpool
Part Number: WP357213
Push-in.
Do-It-Yourself Stories from Customers like You
Washer would fill with water and then do nothing else Richard C. • Torrance , CA • December 05, 2015
I saw videos on it possibly being the lid switch. I used 2 lead wires to bypass the lid switch, which indicated it was indeed the lid switch that was faulty.
I ordered the lid switch, which came in 2 days. I installed it in less than 7 minutes.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP21097
This lid hinge pad fits between the washer lid hinge and the cabinet. It cushions the joint to reduce squeaks and metal wear, helping keep the lid aligned and operating smoothly.
- Provides a protective wear surface between the hinge and cabinet/lid
- Reduces squeaks, creaks, and rattling when opening or closing the lid
- Helps maintain proper lid alignment and smooth movement
- Common signs it's worn or missing: squeaking lid, rubbing/scuff marks at the hinge, loose or wobbly lid
What's included: 1 hinge pad Installation notes:
- Disconnect power to the washer before servicing
- Support the lid to relieve hinge tension and access the hinge area per your model
- Remove the worn pad and press the new pad fully into the hinge location
- Test lid operation; inspect the opposite hinge and replace its pad as needed if your model uses two
Do-It-Yourself Stories from Customers like You
Cracked lid on a whirlpool cabrio washer Doug P. • Kansas City , MO • September 05, 2015
Removed the screws, lifted the old lid out of the hinges. Replaced the hinges, set new lid in the hinges and replaced screws.
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP16123
Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A
Do-It-Yourself Stories from Customers like You
Water inlet valve was corroded and broken washer Sandra H. • Belton , MO • June 26, 2015
Replaced with new part ordered from store
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: 350956
Almond. Size: 13 oz. can. Acrylic appliance paint.
Do-It-Yourself Stories from Customers like You
Age no money to fix it Ronald V. • Cape Coral , FL • August 01, 2015
Was able to match it pretty well the natural age difference was good. The delivery of the product was amazing it took less than 24 hours to get to me and that was standard shipping. Give you guys an A for great !!
Read more
More
$30.52
- Compare At:
-
$36.32
- You Save:
-
$5.80
Genuine Whirlpool part
By: Whirlpool
Part Number: WP90016
Used from harness to top.
Do-It-Yourself Stories from Customers like You
A broken lid switch on my whirlpool stackable twin washer Joseph P. • Indialantic , FL • October 25, 2016
Fixing the problem was quite simple. First, I removed the lid assembly (thanks to the diagrams supplied by AppliancePartsPros.com!). Getting the back two screws out was very difficult because I couldn't see them from the front and I could not move the unit out of the enclosed space. After some trial and error, I located the screws which were 5/16 hex head screws and removed them with a MAGNETIC nut driver. (The magnet assures that the screw will not drop down into the mechanism). Second, I...
Read more
More
$7.44
- Compare At:
-
$8.93
- You Save:
-
$1.49