Kenmore Washer Dryer Combo 110.88732796 (11088732796, 110 88732796) Parts

This U-type nut clips over a sheet-metal edge to create a durable threaded anchor for a screw. It helps secure panels, trim, and brackets so fasteners hold tight and components stay aligned and rattle-free. What it does:

• Clips onto thin sheet metal to provide captive threads where a standard nut cannot be used
• Holds screws securely to fasten panels, trim pieces, or mounting brackets
• Addresses issues like loose panels, missing/broken clips, or screws that will not tighten
• Helps reduce vibration and rattling from unsecured components

• 1 U-type nut

• Disconnect power and shut off gas/water before servicing
• Position the U-nut over the panel edge with the threaded side aligned to the hole
• Start the screw by hand to avoid cross-threading; tighten snugly without overtightening
• Replace any damaged or corroded hardware to ensure a secure hold

The Brake Shoe is an OEM part for Whirlpool washing machines. This part stops the spinning tub during the spin cycle, allowing the washer to transition smoothly to the next phase of the cycle.

Causes of a bad brake shoe can include regular wear and tear, excessive friction from heavy loads, or breakage due to mishandling.  

Symptoms of a bad brake shoe include:

• The washing machine not stopping the spin cycle promptly
• Loud squeaking or grinding noises during or after the spin cycle
• The tub continuing to spin when the lid is opened
• The washer shaking or vibrating excessively during the spin cycle

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Suspension Spring is an OEM part for Whirlpool washing machines. This part helps balance the tub during the spin cycle, ensuring smooth operation and reducing vibrations. By supporting the tub, the suspension springs absorb and dampen the motion as the washer agitates and spins clothes dry.  

Causes of a bad Suspension Spring can include stretching or weakening over time, rust or corrosion, or breakage due to heavy loads or excessive vibration.  

Symptoms of a bad Suspension Spring include:

• The washing machine vibrating more than usual
• Unusual noises during the spin cycle
• The tub sagging or tilting
• The washer "walking" or moving during operation

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This support washer is a flat spacer used within the mechanism to support and separate mating parts, maintaining alignment and smoother movement. Replacing a worn washer helps reduce friction and wear so components operate properly. What it does:

• Maintains proper spacing and support between adjoining parts
• Helps prevent metal-to-metal contact, reducing scraping or grinding noises
• Addresses wobble or excess play when the original washer is worn, deformed, or missing
• Restores smoother movement and alignment in the assembly

• One support washer

• Disconnect power and water supply before servicing; for gas combos, also shut off gas
• Refer to your model's parts diagram for location and orientation
• Track the order of any shims/spacers during disassembly and reinstall in the same sequence
• Tighten fasteners to manufacturer guidance to avoid deforming the washer or binding parts

This small hardware washer sits under a fastener in the specified assembly to distribute load and maintain proper spacing. Replacing a worn or missing washer helps keep components tight, aligned, and operating smoothly.

• Distributes clamping force to prevent fastener pull-through and damage
• Maintains correct spacing/stack-up in the original assembly
• Helps reduce loosening, vibration, and premature wear at the joint
• Typical signs of trouble include rattling, looseness, or misalignment at the connection point

• Disconnect power (and turn off water supply if accessing a wet area)
• Use your model's parts diagram to locate and install the washer
• Replace one-for-one; reinstall any spacers or clips in the same stack sequence
• Tighten fasteners to manufacturer guidance—do not overtighten

The lid hinge bearing is used for the lid hinges on washers and dryers. When functioning properly, it allows the lid to open and close properly. If this is a problem with the bearing, it could make the lid difficult to move. In some cases, when the lid will not close, it means that the machine will not function correctly. Damaged lid hinge bearings should be replaced as soon as possible.The lid hinge bearings see a lot of work since they are in use whenever the lid of the washer or dryer opens and closes. They could become cracked and broken over time. Replacing the bearings is a relatively simple repair that owners can make on their own.This lid hinge bearing is for use with many models of washers and dryers from Whirlpool, KitchenAid, Roper, Estate, Inglis, Maytag, Admiral, Amana, Crosley, and Magic Chef. This is a genuine OEM replacement part that has been sourced from the manufacturer. The piece is sold individually, so if owners need to replace more than one hinge, they will need to buy multiples.

Size: 5 foot long. Rubber fill hose used on most automatic washing machines. Two hoses used per machine.

This motor shield covers the drive motor on top-load washers to deflect splashes, lint, and debris away from the motor and wiring. Replace a cracked or missing shield to help protect the motor assembly at the base of the machine. What it does:

• Covers the washer's drive motor to deflect incidental water and debris
• Helps protect motor windings and terminals from splashes
• Replaces a cracked, warped, or missing cover
• Common signs: visible damage, rattling from the base, or corrosion/debris buildup around the motor

• 1 motor shield

• Unplug the appliance and turn off water supply before servicing
• Access the motor area from the bottom of the cabinet; note the shield's orientation
• Remove the damaged shield and install the new shield fully seated, reusing existing fasteners/clips
• Confirm clearance from moving parts before restoring power and testing

10 - 16 x 1/2

This locking nut is used for many purposes on a range of machines including household appliances. This nut is often used for leg leveling for machines. It will help with vibrations from washers and dryers. If the nut is used for this purpose and goes missing or becomes damaged, it could cause the machine to vibrate more and seem louder.Nuts are made from metal and are built to last a long time. However, there can still be issues that arise. In some cases, the nuts might go missing if they become loose and the machine is moved. They could also corrode over time and need to be replaced. The replacement of the nut is typically a fast and simple repair.The nut is a genuine OEM replacement part sourced from the manufacturer. It can work with washers, dryers, and combo machines, and is compatible with models from Whirlpool, Kenmore, Maytag, and Roper. The part is sold individually. Owners may want to have several on hand.

This thermal limiter (89°C) is a one-time, temperature-sensitive safety device that opens the circuit if internal temperatures rise too high. Replacing a failed limiter helps protect the appliance from overheating and can restore normal operation. What it does:

• Monitors temperature in the airflow/heating path and opens around 89°C to interrupt power when overheating occurs
• Helps protect wiring, controls, and heater components from thermal damage
• A blown/open limiter can cause: appliance won't start, no heat, or stops mid-cycle
• Often indicates an underlying overheating issue that should be corrected

• 1 thermal limiter

• Disconnect power (and gas supply if applicable) and allow the unit to cool before servicing
• Access the limiter per the service information; note wire positions and transfer leads one at a time
• Replace only with the correct rated limiter; never bypass this safety device
• After installation, clear airflow restrictions and verify proper venting and heater/thermostat operation

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

Rubber grommet for motor mount stud.

This replacement siphon break is used in the drain system. It admits air into the drain hose to prevent a vacuum from forming, stopping siphoning/backflow so the washer maintains proper water level and helping prevent leaks from a cracked or clogged break.

• Admits air into the drain line to prevent siphoning and backflow
• Helps the washer maintain correct water levels during fill and rinse
• Common symptoms include water draining out while filling, gurgling/backflow, or leaks near the rear drain connection
• Replace if the siphon break is cracked, brittle, obstructed, or leaking

• Disconnect power and, if needed, turn off water supply; pull the unit forward for access
• Place a towel or pan to catch residual water when removing hoses
• Note hose routing and clamp positions; transfer/secure clamps and ensure no kinks
• Run a brief fill/drain test and check all connections for leaks

This thrust ring is a small spacer that controls end-play on a shaft or gear, keeping parts aligned and reducing friction. Replacing a worn ring restores smoother, quieter operation and helps prevent premature wear in the assembly.

• Maintains axial spacing and limits end-play in rotating assemblies
• Reduces friction and metal-to-metal contact between components
• Helps stabilize shafts/gears to minimize noise and vibration
• Replace if you notice scraping/grinding sounds, wobble, or visible wear on the old ring

• Disconnect power before servicing
• Refer to your model's parts diagram to confirm orientation and stack order with any spacers/washers
• Clean the shaft and mating surfaces; replace any companion parts that show severe wear
• After reassembly, check for smooth rotation and proper end-play before returning to service

Specs: 10-16 x 1/2 inch.