Kenmore Dishwasher 665.13423K702 (66513423K702, 665 13423K702) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: W10795980
The Screw Hole Cap is an OEM part for Whirlpool dishwashers. It covers the screw holes, providing a clean and finished appearance while preventing moisture and debris from entering the screw openings. This helps maintain the dishwasher's aesthetic and ensures that screws remain protected from rust and corrosion.
Causes of a bad screw hole cap can include regular wear and tear, accidental impacts, or misplacement during maintenance.
Symptoms of a bad screw hole cap include:
- Missing or loose caps
- Moisture or debris accumulating in screw holes
- Visible wear or damage to the caps
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Screw hole plastic cap broke during installation Lori D. • Louisville , KY • March 28, 2017
I ordered the part and it was delivered the next day! Amazing experience!
Read more
More
$13.61
- Compare At:
-
$16.20
- You Save:
-
$2.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP302868
Color: Black. Screw for lower toe panel. For Biscuit screw use 3400865, for white screw use WP3400836.
Do-It-Yourself Stories from Customers like You
Dishwasher door panel was rusting Prashant K. • Fishers , IN • October 11, 2014
I had no hope of separating the panel from the frame without damaging the frame since the two parts were rusted pretty badly and the screws holding the panel to the frame were completely beyond salvage. So I had to replace both the panel and the frame. I ended up removing the electrical/electronic connections, removing the panel/frame from the hinge and then replacing it with the new parts. Took about 90 minutes but the hardest part was removing other items from the rusting frame without...
Read more
More
$7.95
- Compare At:
-
$9.38
- You Save:
-
$1.43
Genuine Whirlpool part
By: Whirlpool
Part Number: W10168822
Shaft seal included.
Do-It-Yourself Stories from Customers like You
Sump seal leaked water into diverted motor and of course our floor this is my 2nd kitchenaid to have this problem William L. • Taylors , SC • September 14, 2015
DIY, changed motor and sump. Put a dab of valve lubricant on seal. Wet outer seal of sump to get it to seat in bottom of tub.
Cleaned electrical connectors corroded by leak. Coated connectors with dielectric grease.
Had to buy additional clamp. Two clamps came in the sump package but both fit the smaller hose only. Neither fit the large hose. I wish the correct clamps were included. Home improvement store clamp is a little too wide to fit between ridges in large hose.
Read more
More
$116.26
- Compare At:
-
$139.51
- You Save:
-
$23.25
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8268703
The Adjuster Axle is an OEM part for Whirlpool dishwashers. It plays a crucial role in the height adjustment mechanism of the upper rack, allowing users to customize the rack's position to accommodate different dish sizes. This axle ensures that the adjustment is smooth and stable, providing flexibility in the dishwasher's loading capacity.
You should replace the adjuster axle if it becomes worn out or damaged. Causes of a bad adjuster axle can include wear from frequent adjustments, breakage from overloading the rack, or damage from mishandling.
Symptoms of a bad adjuster axle include:
- Difficulty in adjusting the height of the upper rack
- The rack not staying in the desired position
- Unusual movement or instability of the rack
- The adjuster mechanism not functioning properly
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Screw on one of the roller on upper tray broke Tim J. • Bend , OR • December 28, 2014
Replaced complete roller- screw,wheel and axel. Easy job
Just recently I had to replace upper spray arm. I ordered assembly from you and was completely satisfied with your service and price, that was over 1/2 of what local appliance repair dealer wanted. Very satified with how to do video on this project
Read more
More
$6.95
- Compare At:
-
$8.27
- You Save:
-
$1.32
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9743002
Gasket for upper wheel.
Do-It-Yourself Stories from Customers like You
2 broken "wheel and mount assemblies" (same side) and a few misc upper basket plastic part were broken Michael B. • Wellington , FL • December 29, 2015
With the basket out of the dishwasher, the plastic parts basically snap on and off... popped the broken parts off and the new parts on. The 2 wheel and mount assemblies were a little more complicated. The video on the website advises to disconnect the supply line and drain line... I didn't have to do this. I just pulled the dishwasher out of its cabinet a little over a foot and removed the 2 screws holding each assembly in place and removed them. The previous gaskets (2 PER ASSEMBLY)...
Read more
More
$9.95
- Compare At:
-
$11.84
- You Save:
-
$1.89
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10077840
This dual tine positioner secures two rack tines together to keep dishes stable and properly spaced during the wash. Replacing a cracked or missing clip helps prevent plates and lids from tipping or rattling. What it does:
- Holds two adjacent rack tines in the selected position
- Helps maintain spacing for plates, lids, and trays
- Restores stable loading when the original clip is worn or broken
- Common symptoms: broken/missing clip, tines won't stay upright, items tip over or rattle
What's included:
- One dual tine positioner clip
Install notes:
- Slide the rack out; remove the old clip by releasing its tabs
- Align the new clip over two tines and snap it firmly into place
- Spin the spray arm by hand to confirm clearances before running a cycle
Do-It-Yourself Stories from Customers like You
Plastic posts for mounting screws on back of control panel fractured panel came loose Michael M. • Carrollton , TX • August 01, 2015
Replaced panel
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10177098
The Hex-Head Screw is an OEM replacement part for use in Whirlpool dishwashers. This metal screw measures approximately ¾ inch long. Its primary purpose is to secure the dispenser bracket in place, ensuring stable operation. This hex-head screw is designed for use with compatible hexagonal tools. This makes installation and removal straightforward. This part is sold individually and is guaranteed to fit your dishwasher door panel. This screw is compatible with select Whirlpool brand models including Amana, Crosley, Estate, Inglis, Jenn Air, Kenmore, Kitchen Aid, and Maytag.
Do-It-Yourself Stories from Customers like You
Dishwasher detergent dispenser Howard K. • Rockaway , NJ • November 01, 2015
Pulled a video from online and ordered my parts from Appliancepartspros.com. This was the second repair I've done with your help, the last being my washing machine. This time I replaced the dishwasher detergent dispenser on my Kitchen Aid. You guys make it so simple and give me the confidence to do it myself!
Read more
More
$10.41
- Compare At:
-
$12.28
- You Save:
-
$1.87
Genuine Whirlpool part
By: Whirlpool
Part Number: 4317824
The Power Cord Kit is an OEM replacement part for Whirlpool dishwashers. It is a 3-prong grounded, 16-gauge cord that includes all the hardware needed for installation. Includes all hardware needed for installation.
Causes of a bad power cord can include normal wear and tear over years of use, accidental impacts or cuts to the wiring, or improper installation that damages components.
Symptoms of a bad power cord include:
- The dishwasher not turning on or completing cycles
- Warm or hot power cords during operation
- Frayed, cracked, or exposed copper wiring
This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Mice chewed the drain hose and power cord Noah C. • Eastsound , WA • February 16, 2015
Read directions on how to change the power cord and watched video on your site on how to change the drain hose. Everything went perfectly.
Read more
More
$20.95
- Compare At:
-
$24.93
- You Save:
-
$3.98
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3385088
This dishrack wheel lets the dishwasher rack glide smoothly in and out. Replacing a worn or broken wheel restores easy rack movement and helps keep the rack aligned during loading and unloading.
- Provides rolling support for the dish rack inside the rail/track
- Helps keep the rack level and properly aligned
- Common symptoms include rack hard to slide, wobbling/sagging rack, or a cracked/missing wheel
- Can reduce scraping or clicking noises when moving the rack
What's included: 1 dishrack wheel Install notes:
- Disconnect power before servicing; remove the rack from the tracks as needed
- Release the old wheel from its axle/retainer; note its orientation
- Snap the new wheel onto the existing axle/retainer and ensure it spins freely
- Reinstall the rack and test for smooth operation
Do-It-Yourself Stories from Customers like You
Upper tray roller failure Michael S. • Atascadero , CA • February 28, 2022
Ordered replacement parts and installed them. A lot less expensive than having a dealership fix it.
Read more
More
$12.52
- Compare At:
-
$14.90
- You Save:
-
$2.38
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10348409
This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.
- Provides threaded fastening for panels, brackets, covers, or internal components
- Replaces worn, rusted, stripped, or missing hardware
- Helps reduce vibration and rattling from loose parts
- Restores proper alignment and a secure fit of attached parts
What's included: Includes 1 screw. Installation notes:
- Disconnect power; turn off water supply before service
- Note original screw location and retain any spacers or clips for reassembly
- Start threads by hand to avoid cross-threading
- Tighten snugly; do not overtighten to prevent stripping
Do-It-Yourself Stories from Customers like You
Dishwasher would not start Mark M. • Midlothian , VA • July 16, 2016
Maytag Dishwasher (about 5 years old). Some of the buttons had stopped functioning. Then the Start button began choosing whether or not to work. Eventually it would not start at all. Upon removing the control panel, the first thing I noticed was that the brackets that hold the two lower screws were broken. (So this was the reason that the door was so hard to open from the time it was new.) I trouble shot the thermal fuse, the door-latch switches, and inspected the control board trying to find...
Read more
More
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9741232
Quantity of ONE.
Size: 8-18 x 5/8 inch.
(#8 screw, 18 threads per inch, 5/8 inch long)
Do-It-Yourself Stories from Customers like You
My dishwasher was leaking out copious amounts of water while cycling Michael K. • Oakland , MI • July 11, 2019
While at my sister's house, she showed me how to access & dismantle the housing unit on her dishwasher, thinking the issue might be from that area. So, when I came home, I opened up my housing unit and found that several of the screws had come out and the pump outlet seal was stretched out and partially outside of the unit itself. I located all of the missing screws & discovered I was still missing one, which my husband helped me order with the pump outlet seal. I easily replaced the old seal...
Read more
More
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP676455
Color: Grey. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For white use WP676453. For tips use 676458.
Do-It-Yourself Stories from Customers like You
Rusty tips on tops of posts in top and bottom racks of kitchen aid dishwasher James O. • Bedford , OH • July 04, 2016
Used the vinyl touch up paint on the tops of posts and slid vinyl tips over 130 posts. The paint acts as an adhesive to keep the tips secure.
Read more
More
$24.95
- Compare At:
-
$29.69
- You Save:
-
$4.74
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8268909
Overfill control.
Do-It-Yourself Stories from Customers like You
Washer would not fill with water Ty J. • Hillsboro , OR • July 08, 2018
Replaced float switch and also replaced intake valve. Worked like a charm and the process was as easy as the YouTube video I followed made it seem.
Read more
More
$45.95
- Compare At:
-
$54.22
- You Save:
-
$8.27
Genuine Whirlpool part
By: Whirlpool
Part Number: WP676453
Color: White. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For grey use WP676455. For tips use 675679
Do-It-Yourself Stories from Customers like You
Tines on my dishwasher rack was rusting rust was showing on my dishes Jean M. • Lenoir , NC • January 10, 2015
Ordered dishwasher rack tine tips and bottle of vinyl touch up paint. I applied the paint to each tine and then placed the tips on the tines. I waited a few hours before using my dishwasher to allow the paint to dry and allow the tips to stick to the tines.
Read more
More
$30.95
- Compare At:
-
$37.14
- You Save:
-
$6.19
Genuine Whirlpool part
By: Whirlpool
Part Number: W11631670
This factory-specified screw secures panels, brackets, and internal components in your appliance. Replacing worn or missing hardware restores a tight fit to help reduce vibration, noise, and premature wear.
- Fastens sheet metal, brackets, or plastic parts as designed by the manufacturer
- Helps maintain alignment and reduce vibration/rattling
- Direct replacement for stripped, corroded, or missing screws
- Common signs: loose panels or trim, shifting components, screw won't tighten
What's included: One screw Install notes:
- Disconnect power; shut off water or gas supply if applicable
- Use the correct driver to avoid stripping the head
- Start threads by hand to prevent cross-threading; tighten snugly without overtightening
- Replace one-for-one in the original location per service information
Do-It-Yourself Stories from Customers like You
Some accessories were worn. Wayne C. • Massapeqau Park , NY • April 15, 2020
My son fixed the issue of some wear and tear.
Read more
More
$9.95
- Compare At:
-
$11.84
- You Save:
-
$1.89
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8281156
This replacement screw fastens appliance components such as panels, brackets, or trim. Use it to replace a missing, stripped, or rusty fastener and restore a secure, rattle-free fit in your appliance assemblies.
- Secures panels, brackets, or hardware to maintain proper alignment
- Helps eliminate vibration, rattling, or loose-feeling parts
- Replaces fasteners that are missing, corroded, or cross-threaded
- Typical signs you need it: loose handle or panel, gaps, or hardware that won't stay tight
What's included: One screw. Install notes:
- Disconnect power (and shut off gas, if applicable) before servicing
- Match thread type and length to the original fastener for proper fit
- Start threads by hand to avoid cross-threading; do not overtighten
- Reuse any original washers or clips if present
Do-It-Yourself Stories from Customers like You
Screw on one of the roller on upper tray broke Tim J. • Bend , OR • December 28, 2014
Replaced complete roller- screw,wheel and axel. Easy job
Just recently I had to replace upper spray arm. I ordered assembly from you and was completely satisfied with your service and price, that was over 1/2 of what local appliance repair dealer wanted. Very satified with how to do video on this project
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13