Kenmore Dishwasher 665.1581592 (6651581592, 665 1581592) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: W10833650
Restore smooth loading and secure placement for your dishes with this replacement dishrack. Replacing a bent, rusty, or damaged rack helps keep items upright, improves spray coverage, and prevents flaking or broken tines from contaminating the wash. What it does
- Holds and organizes dishes, bowls, and cookware during the wash cycle
- Slides on the rail system for easy loading and unloading
- Helps maintain proper spray coverage and drainage for effective cleaning
- Common symptoms of failure: rusted or broken tines, peeling rack coating, rack wobbling or derailing, poor rolling, items tipping over
What's included
Install notes
- Disconnect power and shut off water; open the door and fully extend the rack
- Remove rail stop clips/end caps as applicable and slide out the old rack; wear gloves to avoid cuts from sharp edges or rust
- Transfer any reusable accessories (silverware basket, clips, holders) from the old rack if needed
- Slide the new rack onto the rails, reinstall the stops, and verify it glides smoothly before running a cycle
Do-It-Yourself Stories from Customers like You
Bottom dishwasher rack rusting Joanne S. • Palos Park , IL • November 11, 2018
Got a new one. Old one was white plastic coated. The new one is silver a little different in loading and a little smaller
Read more
More
$205.76
- Compare At:
-
$244.85
- You Save:
-
$39.09
Genuine Whirlpool part
By: Whirlpool
Part Number: WP302868
Color: Black. Screw for lower toe panel. For Biscuit screw use 3400865, for white screw use WP3400836.
Do-It-Yourself Stories from Customers like You
Dishwasher door panel was rusting Prashant K. • Fishers , IN • October 11, 2014
I had no hope of separating the panel from the frame without damaging the frame since the two parts were rusted pretty badly and the screws holding the panel to the frame were completely beyond salvage. So I had to replace both the panel and the frame. I ended up removing the electrical/electronic connections, removing the panel/frame from the hinge and then replacing it with the new parts. Took about 90 minutes but the hardest part was removing other items from the rusting frame without...
Read more
More
$7.95
- Compare At:
-
$9.38
- You Save:
-
$1.43
Genuine Whirlpool part
By: Whirlpool
Part Number: 676458
Color: Gray. Includes 125 caps used to cover damaged tips on your dishracks. For blue order 12022. For white order 675679. To attach these tine tips you will need to order the dishrack gray touch-up paintWP676455.
Do-It-Yourself Stories from Customers like You
Rusty tips on tops of posts in top and bottom racks of kitchen aid dishwasher James O. • Bedford , OH • July 04, 2016
Used the vinyl touch up paint on the tops of posts and slid vinyl tips over 130 posts. The paint acts as an adhesive to keep the tips secure.
Read more
More
$27.25
- Compare At:
-
$32.43
- You Save:
-
$5.18
Genuine Whirlpool part
By: Whirlpool
Part Number: WP302711
This pump outlet seal sits on the discharge side of the dishwasher pump to keep the outlet connection watertight. Replacing a worn seal helps stop leaks and keeps wash water contained during the cycle. What it does:
- Seals the joint at the pump outlet to prevent water leakage
- Helps maintain proper circulation by keeping the pump discharge airtight/watertight
- Common symptoms of failure include water under the unit, drips near the pump area, or a flattened/cracked/hardened old seal
What's included:
Install notes:
- Disconnect power and shut off the water supply before servicing
- Remove the toe-kick/lower access panel to reach the pump area; place a towel or pan to catch residual water
- Note seal orientation; clean mating surfaces before installing the new seal
- Seat the seal evenly; reassemble and run a short test to check for leaks
Do-It-Yourself Stories from Customers like You
Loud dishwasher producing dirty dishes Leon F. • Sylmar , CA • November 11, 2015
I nearly shelled out for a new Kitchenaid when I remembered APP and entered my model # just for fun. The interactive diagrams and install videos showed where all the parts "should" be, mine were badly disintegrated, so I replaced the damaged ones and swapped out all of the other easily accessible seals and bearings (also gave it a good and very disturbing cleaning). My parts surprisingly arrived next day and for about $40, the dishwasher is quiet and works like new again.
Read more
More
$24.95
- Compare At:
-
$29.94
- You Save:
-
$4.99
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10348409
This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.
- Provides threaded fastening for panels, brackets, covers, or internal components
- Replaces worn, rusted, stripped, or missing hardware
- Helps reduce vibration and rattling from loose parts
- Restores proper alignment and a secure fit of attached parts
What's included: Includes 1 screw. Installation notes:
- Disconnect power; turn off water supply before service
- Note original screw location and retain any spacers or clips for reassembly
- Start threads by hand to avoid cross-threading
- Tighten snugly; do not overtighten to prevent stripping
Do-It-Yourself Stories from Customers like You
Dishwasher would not start Mark M. • Midlothian , VA • July 16, 2016
Maytag Dishwasher (about 5 years old). Some of the buttons had stopped functioning. Then the Start button began choosing whether or not to work. Eventually it would not start at all. Upon removing the control panel, the first thing I noticed was that the brackets that hold the two lower screws were broken. (So this was the reason that the door was so hard to open from the time it was new.) I trouble shot the thermal fuse, the door-latch switches, and inspected the control board trying to find...
Read more
More
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9741232
Quantity of ONE.
Size: 8-18 x 5/8 inch.
(#8 screw, 18 threads per inch, 5/8 inch long)
Do-It-Yourself Stories from Customers like You
Leaking around dishwasher door previous repair missing parts Patrick R. • Peachtree City , GA • November 15, 2014
I ordered new seals from AppliancePartsPros.com. Finding the right seals was very easy, all based on model number of the appliance. While looking my unit over for other signs of wear, I noticed that a repair done by the prior homeowner to the lower wash arm was done improperly: a seal there was set protruding from the cover, the cover was missing screws, and the arm was missing the upper bushing. So I ordered a new seal, the missing screws, and both the top and bottom bushings (just to be...
Read more
More
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP676455
Color: Grey. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For white use WP676453. For tips use 676458.
Do-It-Yourself Stories from Customers like You
Rusty tips on tops of posts in top and bottom racks of kitchen aid dishwasher James O. • Bedford , OH • July 04, 2016
Used the vinyl touch up paint on the tops of posts and slid vinyl tips over 130 posts. The paint acts as an adhesive to keep the tips secure.
Read more
More
$24.95
- Compare At:
-
$29.69
- You Save:
-
$4.74
Genuine Whirlpool part
By: Whirlpool
Part Number: WP676453
Color: White. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For grey use WP676455. For tips use 675679
Do-It-Yourself Stories from Customers like You
Tines on my dishwasher rack was rusting rust was showing on my dishes Jean M. • Lenoir , NC • January 10, 2015
Ordered dishwasher rack tine tips and bottle of vinyl touch up paint. I applied the paint to each tine and then placed the tips on the tines. I waited a few hours before using my dishwasher to allow the paint to dry and allow the tips to stick to the tines.
Read more
More
$30.95
- Compare At:
-
$37.14
- You Save:
-
$6.19
Genuine Whirlpool part
By: Whirlpool
Part Number: 675679
Color: White. Includes 125 caps used to cover damaged tips on your dishracks. For blue order 12022. For grey order 676458. To attach these tine tips you will need to order the dishrack white touch-up paint WP676453.
Do-It-Yourself Stories from Customers like You
Tines on my dishwasher rack was rusting rust was showing on my dishes Jean M. • Lenoir , NC • January 10, 2015
Ordered dishwasher rack tine tips and bottle of vinyl touch up paint. I applied the paint to each tine and then placed the tips on the tines. I waited a few hours before using my dishwasher to allow the paint to dry and allow the tips to stick to the tines.
Read more
More
$26.95
- Compare At:
-
$32.07
- You Save:
-
$5.12
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3369769
Dishwasher door panel insert. Reversible: white color on one side, black on the other.
Do-It-Yourself Stories from Customers like You
Rusted out front panels but dishwasher still working perfectly so kind of a waste to buy a new dishwasher Dennis Y. • Torrance , CA • October 13, 2014
Bought new top and lower front panels, removed/replaced rusted out panels & now dishwasher looks good as new! Only $34 from Appliance Parts Pros. Better than spending $500 on a new dishwasher.
Read more
More
$34.95
- Compare At:
-
$41.59
- You Save:
-
$6.64
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3369193
Color: Black. Other colors: For white use WP3369614.
Do-It-Yourself Stories from Customers like You
The access panel broke and needed to be replaced this part is located above the toe panel and just below the door Charles K. • Van , TX • February 09, 2016
I carefully removed the insulation and metallic trim from the original part using a small knife. I wraped the insulation with Glad Press'n Seal plastic wrap and attached it to the inside of the new part with double sided tape. I attached the metallic trim to the new part with super glue and then attached the Access Panel to the lower front of the dish washer. It took about 30 minutes to do the job but it was not difficult.
Read more
More
$74.95
- Compare At:
-
$88.44
- You Save:
-
$13.49
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3376397
Included with nut.
Do-It-Yourself Stories from Customers like You
Inadequate cleaning of dishes / detergent residue all over the interior Randy N. • Elkhart , IN • September 19, 2015
I cleaned all the jet nozzles with a toothpick and a pipe cleaner to remove the hard water deposits. I then replace the ring bearing under the bottom spray wand and the ring bearing under the upper spray wand. I also replaced the smaller radial ring bearing. Although none of them looked overly worn, it doesn't take much to cause the spray wands to spray inadequately.
Then, I replaced the float and washer assembly. Although it appeared to work properly when I lifted up on it and let it down, it...
Read more
More
$65.64
- Compare At:
-
$78.11
- You Save:
-
$12.47
Genuine Whirlpool part
By: Whirlpool
Part Number: W11693756
This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:
- Thread-forming Type AB design engages thin metal or plastic components
- Secures panels, brackets, trim, or covers to reduce looseness and vibration
- Replaces missing, stripped, or corroded fasteners
- Helps maintain alignment for proper operation and reduced noise
What's included:
Install notes:
- Disconnect power before servicing; shut off water supply if working near water lines
- Use the correct driver for the screw head; start by hand to avoid cross-threading
- Tighten until snug—do not overtighten to prevent stripping or cracking plastic
- Repair damaged holes or replace worn clips/inserts before installing the new screw
Specs:
- Size: #8-18 x 5/8 in (length 0.625 in)
- Thread type: Type AB, thread-forming
Do-It-Yourself Stories from Customers like You
Door switch on dryer. James A. • Middleburg , FL • January 20, 2020
It was very easy to fix after watching your video..
Read more
More
$10.95
- Compare At:
-
$12.92
- You Save:
-
$1.97
Genuine Whirlpool part
By: Whirlpool
Part Number: WP489069
Size: 1/4 inch hex head, 10-12 x 1/2 inch.
Do-It-Yourself Stories from Customers like You
Broken handle foot pedal and missing parts Donald M. • Lake Arrowhead , CA • April 05, 2015
This trash compactor is in our vacation home. We never use it and now we are selling the house. When I looked to replace it I was amazed at how expensive a new compactor would cost. I found the serial number on the current compact entered it and your web site came up. Your schematics were excellent and made the repair very easy!
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3367052
This hose clamp secures a flexible hose to its fitting to help prevent leaks and hose blow-offs during operation. Replace a rusted, stripped, or distorted clamp to restore a tight, reliable seal at the connection point.
- Applies clamping force around a hose to hold it on a barb or stub fitting
- Commonly used on washer drain and tub-to-pump hose connections
- Helps stop drips at the joint and prevents the hose from slipping off
- Typical failure signs: leaking at the connection, clamp won't tighten, visible rust, broken/warped band
What's included: 1 hose clamp Installation notes:
- Unplug the appliance and turn off water supply; expect some residual water
- Seat the hose fully on the fitting; place the clamp just behind the bead/barb
- Tighten until snug and secure; do not overtighten to avoid damaging the hose
- Run a short test cycle and recheck for leaks at the connection
Do-It-Yourself Stories from Customers like You
Fill hose leaking at crimp fitting by faucet connector faucet adapter leaking (whirlpool portable dishwasher) Ralph P. • San Antonio , TX • August 21, 2016
Replace faucet adapter, replace fill and drain hose assembly. You must remove outer cabinet to be able to route new hoses and access hose connections under tub.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3369505
Detergent cup dispenser actuator assembly.
Do-It-Yourself Stories from Customers like You
Springs detergent releasing pin needed to be replaced Clyde A. • Greenville , SC • October 16, 2025
Received correct parts for Appliance Parts with ease and quickly.
Read more
More
$32.95
- Compare At:
-
$39.21
- You Save:
-
$6.26