Clare August 20, 2015 for Model Number FGHD2465NF1A I had to buy a new lower orbital spray arm but cannot install it. Please does anyone know how to? I cannot find a manual that shows how to install this. The original one I had fell off and melted.
1 Answer Hello Clare. It is simple to install. It snaps into the lower holder. Just press it into place. Read More...
David July 08, 2015 for Model Number PLD4375RFC0 The code is PF, and I checked the wiring under the dishwasher as you suggested. Still Nothing lights up. Thank you.
1 Answer Hello David. If the board is new, the next step is the wiring harness 5304476754 for the unit. Read More...
David July 07, 2015 for Model Number PLD4375RFC0 My dishwasher kept flashing the RF/FR (?) code and would then go out. I unplugged it and it worked. This happened a couple of times and then it just died. I ordered the Control Board, but that did not fix the problem. There is electrical power to the unit. What should I do? Thanks
1 Answer Hello David. PF is power failure and ER is switch failure. There is no RF/FR code. Check the wiring at the terminal block under the unit. Make sure the door switches are good also. Read More...
1 Answer Paul, The ERR Clean S is an indication that there is a keypad error. You will want to try to reset by disconnecting power for approximately 30 minutes. Once you turn the power back on, if the error reoccurs then you will need to replace the control panel 807545704. Read More...
Stephen June 27, 2015 for Model Number FDB4315LFC2 I have a Frigidaire Dishwasher FDB4315LFC2. The unit kept flashing CL code even when I replaced the door latch. I have now replaced the control board, and the dishwasher washes, but the four buttons in the middle of the controls, High Temp Wash, Sanitize, Air Dry, and Delayed Start will not work. What could cause this??
1 Answer Stephen, The buttons in the middle not working would be caused by a faulty control panel. The part number for the control panel is 154639208. Read More...
Tracey May 05, 2015 for Model Number FDBB4365FC3 My dishwasher just stopped working after a short power outage. The circuit breaker was fine, but I went to run the dishwasher and it wouldn't turn on. It is only 6 years old but it is discontinued. Model #FDBB4365FC3
1 Answer Tracey, You will want to check the power supply to the unit. Check at the bottom of the unit where the electrical box is to make sure there is power there and that there is good connection of the power supply lines and the units power lines. If there is power there then check to see if there is power to the control board. If there is power to the control board but nothing is operating then the control board is faulty and would need to be replaced. The control board part number is 5304514670. Read More...
Joanna April 29, 2015 for Model Number Frigidaire FGHD2433KF1 Normal cycle shows 99 minutes when activated. Within 4 minutes, it changes to 73 minutes.
1 Answer Hello Joanna, There could be an issue with the turbidity sensor 154762601 or the control board 5304514670 while the unit could be shortening the cycle appropriately by the clarity of the water. Read More...
Bill April 19, 2015 for Model Number FDB4315LFCO On the keypad, the left side works (wash type), but the Start/Cancel switch will not work.
1 Answer Hello Bill. You will need to order and replace the console 154639208 on the unit. Read More...
Susan April 18, 2015 for Model Number fdb4315lfc3 Had error code ErS. Service person said needed a SS Console. We replaced that. Ran the dishwasher last night it worked, however this morning the drain pump had been running all night and had the ErS code again. Now PF code. Suggestions on what to replace next?
1 Answer Susan, With having already replaced the control panel which would have caused the ER S error code, you will then want to replace the main control board. Read More...
John April 09, 2015 for Model Number FGHD2465NF1A The unit displayed Er s and stoped. I held down the cancel button and it cleared But now - touching any button it moves to rinse. Rinse works fine. Blogs indicate that it is a switch problem and I should replace the Console Assembly. If that does not fix it - I should also replace the Control Board. Do you agree? If I purchase both and do not need the control board can I return it? Thanks John
1 Answer Hello John. Yes, based on the information you provided, it leads to the console on the unit. Read More...