Alice June 01, 2018 for Model Number ATF6000ES1 Unit turns on and spins but it will not drain the water. It displayed error 23.
1 Answer Hello Alice, The fault code indicates power is not getting to the drain pump. This can be caused by a poor connection or broken wire, a bad drain pump 137221600, or a failed control board 134523106. Read More...
Sherry March 20, 2016 Don't know model number and washer was working fine. I hit something and know cycle signal light is on and all the buttons light up but the door lock light they all lights keep blinking it feels like it on some sort of lock.
1 Answer Sherry, The most likely cause of this issue will be that the control panel is locked out or the door switch in the latch are not making causing the unit to think the door is open. Read More...
Chris September 12, 2015 for Model Number FAFW3511KW0 A few weeks ago, my Affinity front-loading washer started shutting off between the wash cycle and the first drain-and-rinse, leaving the load soaked in sudsy water. At first, restarting the washer solved the problem; the second time through everything worked fine. Two days ago it happened again, only this time the washer failed to restart. The controls seemed to function normally, and I heard relays click when I pushed 'Start', but after that it just sat there and hummed. Thinking that the drain sump might be clogged, I cleaned and reinstalled it. Once I got everything back together, I checked for Error Codes. It showed E75, indicating Test 12 - Check NTC resistance. Unfortunately, this model is not equipped with a booster heater, and so has no NTC. That location on the back of the drum is just blank plastic. As it stands now, I have the washer hooked up and plugged in, trying to run the Clean cycle, but when I press 'Start' all that happens is the door locks. I am about to try the Diagnostic Test, but should I pretty much assume that I'll be stuck getting a new control board?
1 Answer Hello Chris. Yes, based on the information you provided, it sounds like the control board 137006060 is bad and will need to be replaced on the unit. Read More...
Todd January 09, 2015 for Model Number ATF6000ES1 My Frigidaire Affinity front load washer (ATF6000ES1) has no problem with draining and doing a final high speed spin for all the cycles EXCEPT the Spin Only cycle. Every once in a while, on a heavy load or load that the washer is unable to balance for spin, the washer will finally give up without high speed spin. My wife then tries the Spin Only cycle. The washer goes through the drain portion of the cycle, slowly rotates the load in alternating directions 7 times (I think), and then totally shuts down (all lights off) at 6 min remaining without attempting any sort of high speed spin. This happens with a load or empty. Holding the Cancel and Start buttons shows a E47 code. I checked the Door Latch assembly PTC and it showed about 1600 Ohms so it should be OK. Next step per the Washer Tech Data Sheet is to replace the Main Control Board. Does my problem sound like it should be solved doing this? Thanks!
1 Answer Hello Todd, Since the fault code indicates the board thinks the door PTC circuit is open in spin and the unit will go through the spin cycle in the cycles, the board 134523106 has to have an issue. Read More...
Lisa K. September 07, 2014 for Model Number ATF6000ES1 The frame around the slide-in soap dispenser is broken, I don't see a part. I don't need control panel, but it looks to be attached to it before it was broken.
1 Answer Lisa, you'll need the housing which is now available as an assembled part with the valve, part number 134409320. Thanks. Read More...
Luis August 04, 2014 for Model Number ATF706BZHSO What is the problem when during operation, washer stops giving error code E57?
1 Answer Hello Luis. Sorry, the model number you provided is not working. It shows as a commercial unit in which we do not supply parts for. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Matt June 24, 2014 for Model Number FAFW3511KW0 My Frigidaire Affinity front loading washer keeps coming on by itself and beeping. I can turn it off but it comes back on in about 30 seconds. Please help.
1 Answer Hello Matt. Based on the information you provided, you will need to order and replace the control board 137006060 on the unit. Read More...
Doug June 20, 2014 for Model Number ATF600FS1 I am receiving an error code 23 on the display. Which I found out is the "Drain Pump Relay on the control board failed" Do I need to replace the whole control board?
1 Answer Doug, If the issue is in the control board relay, Yes, you will need to replace the control assembly 137006030. But first check and make sure there are no loose or broken wires between the control board and the drain pump 137221600 and the drain pump is running and not seized or defective. Read More...
Scott April 12, 2014 for Model Number ATF6000E The washer doesn't do a final spin. I've checked the pump, which is working fine, the hoses are all clear and water is draining, and the door lock is functional. The control is giving E75. Searches don't correlate E75 with a spin issue. Do I need to replace my main control board or something else?
1 Answer Hello Scott. Water temperature sensor circuit. You will need to check the valve and the thermistor. Read More...
Lisa February 27, 2014 for Model Number LTF6000ES1 My washer will not agitate or spin. Error code E21. I cleaned out the drain hose/coin catcher & reset the error code, tried to turn it on again but still not working & giving me the E21 code again. What do I need to replace? Thank you
1 Answer Hello Lisa, This fault code signifies the water is not draining out fast enough. If there were debris in the sump area that could have contacted the pump impeller, the pump 137221600 has most likely failed. Read More...