M.R.S. February 13, 2016 for Model Number FAFS4272LA0 Recently got an E58. Diagnostic test did not spin in high. Did test #8 from Tech Sheet. Tub and Motor Spun Freely. All connections secure. Ohm'ed motor winding's and were within specs of Tech sheet. So Motor Control was replaced. Did a diagnostic spin and it checked out. Did a small load and it went through a whole cycle fine. Second small load and E58 appears. I've already replaced the Motor Control. Am I just changing parts? How can I pin point this problem? I gather the motor control monitors current and speed control? It will spin in high in diagnostic mode with no codes; empty tub. AS WITH OLD MOTOR CONTROL it would not spin at all in high in diagnostic mode.
1 Answer Hello M.R.S., Since it is possible to have a bad new board 137260800, I would replace this board again. You should also double check the resistances of the motor windings and the harness. The motor control 134618213 is likely at fault with these symptoms. I could not help but notice the board you listed is not on the manufacturers parts for this model. Read More...
Kerch T February 13, 2016 for Model Number 417-48112701 I can not get it to give me any error codes it will stop and flash all the vertical lights over the start button the clothes are sopping wet I can turn it to rinse and spin I don't know when it is stopping I what should I replace?
1 Answer Kerch, If you can put the unit to drain and spin and it will spin out then the issue will most likely be with the control board which is part number 137005020NH. Read More...
P. February 01, 2016 for Model Number CFW5000 FW1 I replaced the control board, as you suggested. But now I have to push on the door to get it to operate. Is it the door striker or the door latch assy.? Thank you, Phil
1 Answer Hello Phil. Check the strike. If it is good, then replace the latch on the unit. Read More...
P. January 25, 2016 for Model Number Crosley CFW5000FW1 You answered me earlyer about the no start problem and your reply was the Contorl Board Part Number: AP3891780...thank you... Is there a way to test this control board before I buy the new one??
1 Answer Hello P. If the start button is not working on the control board and it is timing out, then you have a bad board. There should be a tech sheet in the unit. You can use this sheet to run diagnostics on the unit. Read More...
P. January 25, 2016 for Model Number Crosley CFW5000FW1 Push start and the lights come on and in a few seconds they all go out and does not start. No error code
1 Answer Hello P. Based on the information you provided, it sounds like the control board 137006030 is bad and will need to be replaced on the unit. Read More...
Joel A January 18, 2016 My 2008 frigidaire debt load washer did not spin or drain, replaced pump, door lock assembly, then the main control board with a code of E41 to no avail. After replacing the main control board I got an error code of E59. The motor spins freely with/without the belt on. Is it safe to say the problem would be the motor control board or speed control board, and to replace this part? Thank you, Joel Anderson
1 Answer Hello Joel. Disconnect harness from motor and check resistance on terminals 4 and 5 on motor, should be between 105 and 130 ohms. If good go to next step. Disconnect the plug from the motor and measure the resistance of the windings (pin 1 to 2, pin 1 to 3, pin 2 to 3). All readings should be between 4 and 6 Ohms. If the readings are correct, replace the speed control board. If the readings are incorrect, replace the motor. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Del January 15, 2016 for Model Number FTF2140FS1 Wash machine will not start. The indicator lights come on, the door locks, but it does nothing. It does work on the rinse / spin cycle but no other cycles.
1 Answer Hello Del. If some cycles work and others do not, you will need to order and replace the control board 137005000NH on the unit. Read More...
Jerry January 07, 2016 for Model Number ATFB6700FS0 My washer will not start. When you press the start button all the lights come on even the door lock light and you hear a slight hum from the back left corner of the machine coming from the area close to or below the water control valves that last a few seconds and then the machine shuts off. I ordered a door lock assembly from you guys hoping that would correct the problem. Installed it but I still have the same problem. There are no codes showing so I am at a loss as to where to go from here. Any suggestion would be greatly appreciated. I think the machine has a diagnostic mode but I cant seem to locate any instruction on how to initiate it,or how to get it to show any code that may be stored.
1 Answer Hello Jerry. Check and make sure the valve is not clogged. If not, then it sounds like the valve is bad and will need to be replaced on the unit. Read More...
Jim November 27, 2015 for Model Number GLTF2940FS2 How is motor control board held down. The machine belt failed . This machine was service for pump issue. The top panel was replaced. The back panel was put back on unside down and with only three of six screws. Found three missing screws in side bottom of machine. I did not move machine from wall . Had I did , I would of call service people back. I need known how control board is mounted to side wall or bottom of the machine. There is no angle bracket..
1 Answer Jim, The Speed control board is held in by screws that go into the base of the unit. Read More...
Thom November 23, 2015 for Model Number GLTF2940ES0 The machine does not wring all the water out on the last spin cycle except on normal, heavy sport cycles. We fixed the door latch as that is what the error code said.
1 Answer Thom, If the unit is working properly in the normal and the heavy sports cycle then this will most likely be an issue with the speed control board. The part number for the control board is 134743500. Read More...