Jennifer July 16, 2012 for Model Number LTF2140FS2 WHen I start the washer the no spin light comes on and then it will not go any farther. Is it my pump or something else?
1 Answer Jennifer, If there is water in the tub, it could be a drain pump issue, If not, then you need to start looking for a faulty door latch assembly 131763256 (does the door lock ?) or a motor control board 134743500 . Thanks Read More...
Ruben July 05, 2012 for Model Number ltf600es0 If looking at the drain pump from the back which is terminal 1 an which is terminal 2.
1 Answer Hello Ruben, Looking straight at the terminals, pink/black to terminal 1 on the left and black/red to terminal 2 on the right. Read More...
Ruben V. July 05, 2012 for Model Number LTF6000es0 How are the color coded wiring connected on the back of the drain pump ap4359998 connected? Thank you for your help!
1 Answer Hello Ruben, As per the wiring diagram, pink to terminal 1 and white to terminal 2. Read More...
Ruben July 03, 2012 for Model Number ltf6000eso Pump was clogged. Now getting error 23 control board bad. Is it possible I inverted the wiring connection in back of pump an damage the control board. Connected black/red on top and pink/black on bottom. Need help!
1 Answer Hello Ruben, This is the error code for the relay on the control board 134523106. Since the drain motor is an ac motor, I seriously doubt wiring the motor backwards was the cause of the board failure. The only way this could have damaged the board is if one of the wires were shorted to the other or to ground. Read More...
Chris June 01, 2012 for Model Number LTF6000ES1 Where can I find directions to replace the drain pump assembly?
1 Answer Hello Chris. First and most importantly, unplug the unit to prevent electrical shock or death. Next remove the bottom panel across the front of the unit. The drain pump is in the bottom of the unit right in the center. Here's a really good tip to prevent swimming around in there. If you have a shop vac, get all of the water out that you can because when you remove the hose, all of the water will come out at once. Remove the wires to the pump first, then the hoses. Now install the new pump 137221600 in reverse order. Read More...
Greg F. May 23, 2012 for Model Number model 417 44052401 My washer will not drain the water and I think we may have clogged a filter or something. We washed a rug that lost a lot of it's rubber-like backing. Where is the drain pump located and how can I check if it is clogged?
1 Answer Hello Greg, First and most importantly, unplug the unit to prevent electrical shock or death. Next remove the bottom panel across the front of the unit. The drain pump is in the bottom of the unit right in the center. Here's a really good tip to prevent swimming around in there. If you have a shop vac, get all of the water out that you can because when you remove the hose, all of the water will come out at once. Remove the wires to the pump first, then the hoses. once you remove the pump, you can take it outside and flush it with a water hose to remove all of the foreign material from it if you refrain from soaking the motor itself. If the motor get wet, don't panic. Just place it in front of a fan long enough for it to dry before reapplying voltage. It probably isn't a bad idea to remove the hose from the tub also to clear the hose and get anything out of the tub that you can rake out. Note: the outside of the inner tub has sharp edges made all over it so try not to touch it through the hose connection opening. Once you have everything cleared out, reassemble in the reverse order. Since you do have to reuse all of the parts, it isn't a bad idea to put them in a place that no screws or other hardware is lost. If you have any more questions, please don't hesitate to ask us. Read More...
Lisa May 13, 2012 for Model Number nmws336fs01 The pump is making a grinding noise but will not pump out the water. The washer will spin though if you make it think the lock is engaged, what do you think it could be? I can hear the water go back into the tub when I raise and lower the hose. I thought I read in other posts that there is a flap that does not allow return flow, almost like a check valve?
1 Answer Hi Lisa. Drain Pump Assembly - Washer drain pump and motor assembly. Includes red flapper to prevent the drain water from backing up. Item Number: 137221600 . A grinding pump will quickly burn out. Remove the front panel and inspect the impeller inside the pump. Is it spinning loose on the shaft ? Is there anything small stuck inside it ? Use a shop wet vac and inspect the hoses for clogs. Have everyone be removing any pocket items as the pumps are now all high speed, energy efficient pumps. Thank You. Read More...
David B. May 06, 2012 for Model Number ATF8000FS1 The machine stoped spinning and only hums from the pump motor it will not drain or spin. I hit the motor a few times and it made a 1/4 turn on its own once, what can I check to know what part is giving me the problem?
1 Answer Hello David. If the unit does not spin, make sure the pump is not clogged on the unit. If the pump is clear and working properly, you may have a bad door lock assembly 131763256 and it is not sending signal to the control board that it is locked and will need to be replaced on the unit. Read More...
Cathy March 27, 2012 for Model Number AFT6000ES Do you sell just the red flapper on the drain pump assembly?
1 Answer Cathy, found model ATF6000ES* (F and T reversed). The red flap is not available separate from the pump 137221600. Thanks! Read More...
Angelina February 16, 2012 for Model Number fwfb9200eso I am receiving an error on my washer E20 also the water will not drain. Do I need to replace the pump or the motor? Thank you
1 Answer Hi Angelina. You have a service tech. sheet in the unit. It will be under the top or under the front of the lower panel. It will show you the codes. E21 is an water not pumping out fast enough. The drain pump is part # 137221600. Make sure you clear the drain hose and the standpipe at the same time . Thank You. Read More...