Jossi February 21, 2025 for Model Number WRB322DMBM03 I bought the jazz board to replace the old one, I followed the steps that came with the board to program it and everything went smooth until I tried to confirm the programming after putting the fridge code, it doesn’t blink (confirm the coding) what should I do? Thanks for your help
1 Answer Hello Jossi, thank you for contacting Appliance Parts Pros. If you ordered and installed control board [WPW10503278] it is the wrong control board, jazz board [W11524469] is the correct one for this model. If you ordered and installed [W11524469] and it is not accepting the programming code and the code matches what is found on the model/serial plate then it is possible you have a defective control board out of the box. Read More...
Brian September 13, 2024 for Model Number 596.467934351 REF. CONTROLS AND LIGHTS WILL FLICKER. SEEMS TO SHUT OFF AND WILL START BACK UP IF DOOR IS OPENED. WE HAVE SEEN WHEN DOOR IS OPEN LIGHTS AND CONTROL WILL GO BLACK LIKE POWER IS LOST. POWER CORD IS SECURE TO 120V OUTLET . CONTROL BOARD CONNECTIONS ARE PLUGGED IN. LEANING ON CONTROL BOARD IS GOING BAD??
1 Answer Hello BRIAN, thank you for contacting APP, This is an issue with the Main Control WPW10503278. Read More...
Lorenzo T July 12, 2024 for Model Number 59669312010 Yes i have a question about this frig some times the board control the numbers some times go up and cant move down do i have to replace the board or the temperature sensor thanks in advance
Sonny August 24, 2023 for Model Number ABR2222FES After installing the new circuit board and completed the programming procedures, everything seems to be working to include the condenser blower by the compressor, evaporator blower (it's blowing air from the bottom freezer drawer to the upper refrigerator compartment. There is a vibration after physically touching the compressor (I wish I have a clamp-on ammeter to confirm). I left it running for 30 mins and still warm inside (top and bottom. Help ! Thanks
1 Answer Hello Sonny, with the fans and compressor running and the ref interior (both ref and frez) not getting cold that points to a sealed system problem (likely compressor failure or freon leak) , suggest you contact a service tech to check further. Read More...
Denise July 17, 2023 for Model Number washer This # is the same for our Maytag washer not a refrigerator. There are issues with the board on top of the washer. This is the # we got off it. Is it for a washer also?
1 Answer Hello Denise, not they would not be the same part, if you repost your question with the washer model number we can locate the correct board for you. Read More...
Kelly January 25, 2023 for Model Number WRF535SWHZ003 The compressor will not start. I replaced the relay and capacitor it ran for a day. Now the compressior makes a very loud buzzing noise and clicks but will not start. the voltage in the out is reading 122.7volts. any suggestions ?
1 Answer Kelly, as the start relay W10873801 and run capacitor WPW10350564 have been replaced and there is 120VAC reaching the compressor, the unit would have a sealed system failure that would likely be caused by the compressor itself if the blue wire is set at the terminal farthest from the center of the start device. Read More...
Pmh October 07, 2022 for Model Number MFF2558VEM5 My ice maker stopped working. I replaced it and it made one tray of ice but then quit working. I checked for power to the ice maker and no power. I am thinking that this is an issue with the frig control board. I was getting clicking from the fridge and though it was the ice maker motor but the clicking is not coming from the freezer section. What do you think?
1 Answer PMH, Check the temperature in the freezer to make sure that it is between 0 and 5 degrees. Also, when testing the icemaker power, make sure that the light switch is pushed in. If there is clicking then check to see if the noise is coming from the start device on the compressor as this would cause higher temperatures. Read More...
Brent September 19, 2022 for Model Number KBRS19KTMS2 WHEN REPLACING THE ELECTRONIC CONTROL BOARD, YOU NEED TO RE PROGRAM USING THE CODE ON THE MODEL INFO PLATE. IN MY CASE, THE MODEL CODE IS 21, YET THE DIGITAL NUMBER PAD USED TO PROGRAM ONLY HAS ONE NUMBER (I.E., 1 TO 7) HOW DO YOU PROGRAM THE CODE 21 USING ONLY ONE NUMBER??
1 Answer Brent, When programming the digit in the freezer display will be 2 and the digit in the refrigerator display will be 1. Read More...
Tony September 03, 2021 for Model Number Kitchen aid model KRBX102EWH00 After power surge, fridge wasn’t working. Repairman has replaced control panel twice, two fans, no luck. When power was on, technician put probes across the control board. Starts out at 99 volts, goes down to 8 volts, then zero. Tech can’t figure it out. Any ideas??? Please???
1 Answer Tony, Thanks for the question!!! I would check to make sure the right program number was set on the control board. Program instructions are included with the control board. Read More...
Jim July 05, 2021 for Model Number GX5FHDXVQ06 The ice maker tray has stopped filling with water. It will cycle normal, but obviously makes no ice. I have verified the water flow path from the wall to the outlet of the water tube by directly apply 120vac to the water solenoid valve. All other aspects of the fridge/freezer work properly. This leads me to think that the control module has an issue with the solenoid valve control portion of it. Thoughts?
1 Answer Jim, Based on the information provided if the ice maker cycles and is not calling for water the issue would be in the ice maker module WPW10281342 which has been discontinued by the manufacturer & is no longer available. Therefore you would need the ice maker assembly complete W10884390 Read More...