Wrf535swhz003 Parts

All you need is a nut driver. The end cap is attached to the side of the refrigerator cabinet with two long screws. Once you remove them, you should slide the end cap towards you. It will release the internal clip that holds the front of the end cap. You should then unscrew the metal slider from the end cap. Assembly of the new end cap is the reverse. You should first attach the metal slider to the new end cap. Attaching the new end cap to side of the refrigerator cabinet is a little tricky.... Read more

I replaced the icemaker. It was fairly easy, with the most difficult part being access to the icemaker in the bottom freezer. I loosened two screws, removed one additional screw, disconnected the wiring and removed the old icemaker. I mounted the wiring harness and ice level sensor arm from the old unit onto the new icemaker and installed it with no problems. I wish I'd done this months ago instead of repeatedly attempting to repair the old icemaker. Read more

I bought new gaskets, which were expensive! At least the repair was easy. Pulled out the old ones, pressed in the new ones. Had to redo them because I didn't notice the little flaps that need to be covering the space in the middle, between the doors. So, pulled them off, and turned them around, and pressed them on again. Maybe 10 minutes? Read more

No instructions are included with either piece, which makes installation take more time and care. Tools needed: Small standard flat blade screwdriver, box knife or other knife with at least a 2" long blade, super glue. Remove the old main crisper frame: 1. Remove old main frame by lifting upward and outward. 2. Remove the center rail from the frame. May require bending of the main frame to remove it. 3. Remove the crisper front panel by unsnapping from frame. This is easily done by... Read more

• Fridge runs too long
• Freezer not defrosting
• Freezer too cold
• Won't start

A bit of research on the internet indicated the most likely problem was with the defrost system. I found the service manual for the refrigerator and was able to determine that the defrost heater and thermostat passed the self test. The refrigerator would perform a forced defrost which resulted in a cold refrigerator. More research revealed that this particular refrigerator does not have a defrost timer, instead the defrost cycle is controlled via the Electronic Control board which is also... Read more

• Not dispensing water
• Ice maker dispenses too little ice
• Ice maker won't dispense ice
• Ice maker not making ice

Ordered part and replaced it Read more

Looked up parts based on fridge model number, watched videos, and replaced parts using just a few tools... easy. Parts came quick, well packaged. After 16 years, plastic parts deteriorate and break. The fridge was operating fine, but the drawers and covers were failing. Much cheaper to replace a few parts ($$-$$$) than buy a new fridge ($$$$). The new parts matched up exactly to old ones. The videos were very helpful, but not perfect... for the Crisper Frame, there was a structural metal... Read more

Door gasket was easy to remove and reinstall. Original gasket was penetrated while cleaning food stuff from folds in the seal below the frig doors. (Gasket is very fragile so don't try to expand the folds while cleaning. I used my finger and a paper towel but in hindsight should have used a Q-Tip. Also, when installing the new gasket you have to be sure the seam folds over the edge of the door and doesn't get caught underneath. Read more

I watched the video on replacing the switch on a side freezer where prying out to original switch did not look difficult. I then got on the floor and tried to pry out my switch. Had a terrible time (locking tab or switch body hardened with time?) and mangled the switch terribly and the upper panel of the freezer somewhat, but the switch did come out. AND THEN the top freezer panel with the switch and light assembly fell out into my hands! I was able to unplug one Molex connector and the... Read more

• Fridge too cold
• Freezer too cold
• Fridge too warm

Toughest part of this repair is figuring out how to get things apart. Amana doesn't provide you a repair manual showing how to disengage the various plastic covers. Initially disassembled the bottom freezer compartment so I could get to the evaporator coils; they were completely frozen in block of ice, restricting air flow to the fridge above. Obviously, the auto defrost cycle had not been running, or was short-cycling. Manually defrosted. Found this link for running diagnostic tests on the... Read more

Replaced door switch - it took less than 5 minutes - works perfectly Read more

• Noisy
• Fridge too warm

The fridge is 20+ years old in a home we recently moved into. It sounded like a motor getting stuck on something or grinding weird... was hoping it wasn't something more serious. Found this site, clicked 'noisy' and got the replacement evaporator fan motor blade as well as the motor evaporator. Turned out I didn't really need to replace the fan blade, but since I had it and ours was old, figured I might as well put in the new parts. Followed the videos here, which were really helpful. The... Read more

I looked up the parts online at AppliancePros.com! To my surprise, the detailed drawings showed that I could replace the center rail (about $13) instead of the entire lower shelf (about $100)! I also ordered a replacement shelf bin that had broken. I looked at other sites for the parts, but they were cheapest here. I ordered the parts LATE Wednesday and they were at my door Friday afternoon! Super fast! The order was accurate, packed well so it arrived damage free, Read more

Replaced relay and capacitor attached to compressor Read more

Replaced water valve and ice maker Read more

We turned off the circuit breaker. We then removed the light cover and then the control panel. We disconnected the Keyboard, Utah, plugged in the new one and turned the breaker on to see if everything worked. We realized that we did not need a new jazz board so that is being returned. The old Keyboard was removed, the new one attached and all the parts were put back. The frig works fine now at the recommended settings of zero and 38F. Read more