Range Burner & Related Parts

This surface burner cap sits atop the gas burner head to distribute flame evenly and protect the burner from spills, helping restore steady flames and reliable ignition when the original cap is worn, warped, or missing.

• Distributes flame for more even heating across cookware
• Shields the burner head from boil-overs and debris
• Supports proper ignition when correctly seated and level
• Common signs it's needed: missing cap, chips/cracks, warping, uneven or yellow flames

• Allow the cooktop to cool completely; shut off gas/power if performing additional service
• Remove the grate, lift off the old cap, and clean the burner head surface
• Center the new cap on the burner head so it sits flat and does not rock
• Test the burner; if ignition is delayed or flames are uneven, reseat the cap

The Surface Burner Base is an OEM part for Frigidaire gas ranges. It provides a stable foundation and housing for the range's burners. Each burner base has a molded indentation to securely hold the burner assembly in place while cooking. 

Causes of a bad Surface Burner Base can include warping or distortion from overheating, cracks or punctures from impact or mishandling, or damage from corrosion over time.

Symptoms of a bad Surface Burner Base include: 

• Burners wobbling or moving out of position during use
• Gas or liquid leaks around burner housing 
• Irregular or uneven cooking performance 
• Loose, damaged, or missing burner assemblies

This genuine OEM Frigidaire base is also compatible with some Electrolux, Gibson, Kelvinator, and Kenmore models.

The Burner Head is an OEM component specifically designed for Whirlpool gas ranges. Located beneath each cooking surface, it allows precise flame control and heat delivery for safe food preparation.

Causes can be related to accumulated food or mineral deposits distorting gas/air mixing pathways. Normal aging effects like rusting also impact burner functionality.

Symptoms of a bad burner head include:

• Flames appear unusually high, low, or unstable
• Uneven cooking results occur on burner surfaces  
• Singeing or burning odors develop during use
• Any ports that appear collapsed or restricted

This OEM Whirlpool replacement burner head restores consistent heat levels. Installed promptly to repair scorches or damage, it prevents continued surface and connection deteriorations to the manifold. 

Compatible also with some GE and Frigidaire ranges, this part ensures safe, dependable cooking control.

This small cooktop bracket secures designated components beneath the cooktop surface, keeping them properly positioned and stable. Replace a damaged or missing bracket to restore alignment and reduce movement or rattling during use.

• Provides mounting support for specific under-top components, per model design
• Helps maintain proper alignment and stability of cooktop parts
• Replace when visibly bent, cracked, or corroded

• Disconnect power; for gas models, also shut off gas and allow the unit to cool
• Remove surface components as required (grates/caps/heads for gas; elements/panels for electric) to access under the top
• Lift or remove the cooktop as directed in your model's service information and secure the new bracket with existing hardware
• Reassemble, verify alignment, and for gas units check for leaks if any gas connections were disturbed

Black. C Burner

Replacement snap-on cap that restores a finished appearance and helps protect underlying components from dirt and accidental contact. Fits original mounting locations to cover exposed hardware and improve appliance safety and aesthetics. What it does:

• Covers and protects exposed hardware, terminals or posts to reduce debris buildup and accidental contact.
• Restores a clean, finished look to panels, trim or appliance edges.
• Helps reduce rattling or vibration noise caused by missing trim pieces.
• Use when the original cap is cracked, broken, missing or when exposed fasteners are visible.

• Always disconnect power (and water, if applicable) before attempting any repair.
• Remove the damaged cap by hand or with a small pry tool; press the replacement cap onto the mounting post until fully seated.
• Avoid excessive force during removal/installation to prevent damage to the mounting post or surrounding trim.
• If mounting posts or clips are damaged, replace those components to ensure a secure fit.

The Regulator is an OEM replacement part for Whirlpool gas ranges. It regulates the flow of gas from the supply line to the burners, ensuring safe and efficient operation of your range. It maintains a consistent gas pressure, allowing for accurate and controlled heat distribution during cooking.

A bad pressure regulator can occur due to wear and tear, clogging, or damage to the internal components. If you notice symptoms such as uneven flame, difficulty in igniting the burners, or gas leaks, it may be time to replace the pressure regulator.

Symptoms of a bad gas pressure regulator include:

• Uneven flame
• Difficulty in igniting burners
• Gas leaks

This Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This natural gas burner orifice regulates gas flow to the cooktop burner for a consistent 17K output, restoring proper flame size and heat. It's a direct-fit replacement designed for compatible Whirlpool-range gas valves and burners. What it does

• Controls gas flow to the burner so the flame reaches the intended heat output
• Helps correct weak or uneven flames when the orifice is clogged or worn
• Can resolve ignition or simmering problems caused by improper gas flow
• Matches the OEM 17K specification for proper burner performance

• One natural gas burner orifice (17K)

• Turn off the gas supply and power to the appliance before servicing
• Remove burner components carefully to access the orifice; avoid forcing fittings
• After installation, check for leaks with a soap solution or approved gas leak tester

Approx 1-1/2 inches in diameter

This LP conversion kit converts a compatible gas appliance from natural gas to propane (LP) so burners operate with the correct orifice sizing and fuel flow. Use when changing fuel type to restore proper flame performance and safety. What it does:

• Replaces orifices and/or components needed to match appliance fuel flow to propane (LP)
• Helps restore proper flame size and color after switching fuel types
• Addresses symptoms such as weak or uneven flames, hard ignition, or yellow/orange flame tips
• Ensures appliance operates as designed on the correct fuel when installed per OEM instructions

• Follow the OEM conversion instructions exactly and keep the original parts; improper conversion can be unsafe.
• Shut off the gas supply and power before starting; check all connections for leaks after installation.
• Some conversions must comply with local codes — verify requirements before proceeding.
• Use only the orifices/components supplied with the kit for the specified appliance; do not modify parts.

This sealed surface burner is a direct-fit replacement for a damaged or worn black cooking element, restoring reliable heat while keeping spills out of the appliance interior for easier cleaning and safer use. What it does:

• Heats cookware for baking, boiling and frying on electric ranges; replaces elements that fail to heat
• Sealed design helps prevent spills and debris from entering the cooktop cavity for cleaner operation
• Use when a burner heats intermittently, won't heat at all, shows visible damage, or produces arcing
• Fits the original mounting and electrical connector for straightforward replacement

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing
• Remove the cooktop or access panel as required and keep track of screws and fasteners
• Inspect and align the element's connector; do not force connections—replace damaged wiring or terminals

The Gas Burner is an OEM replacement part for Frigidaire gas wall ovens and cooktops. It facilitates safe and efficient cooking by providing a controlled source of flame. 

Symptoms of a bad gas burner include: 

• Uneven or unpredictable heating across the burner surfacea
• Flames not igniting or not staying ignited
• Burner components cracking, rusting, or becoming discolored
• Gas smells coming from the burner area

Causes of gas burner issues can be wear over time, contamination of ports/orifices affecting gas flow, or damage to ignition components. Ceramic burner materials may also degrade with heavy use or exposure.

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

The Surface Burner Base is an OEM part for Frigidaire gas ranges. It provides a stable foundation and housing for the range's burners. Each burner base has a molded indentation to securely hold the burner assembly in place while cooking. 

Causes of a bad Surface Burner Base can include warping or distortion from overheating, cracks or punctures from impact or mishandling, or damage from corrosion over time.

Symptoms of a bad Surface Burner Base include: 

• Burners wobbling or moving out of position during use
• Gas or liquid leaks around burner housing 
• Irregular or uneven cooking performance 
• Loose, damaged, or missing burner assemblies

This genuine OEM Frigidaire base is also compatible with some Electrolux, Gibson, Kelvinator, and Kenmore models.

This orifice spud is the small gas burner fitting that holds the burner orifice and helps direct fuel to the burner for proper ignition. It restores correct gas flow to the burner assembly for reliable ignition and flame. What it does:

• Secures the burner orifice in the burner tube so the correct-sized jet is positioned for ignition
• Helps maintain steady, consistent gas flow to the burner
• Commonly replaced when burners fail to light or flame is weak/irregular
• Works with the burner tube assembly to ensure proper burner operation

• One orifice spud

• Turn off gas supply and unplug appliance before beginning service
• Use correct tools and replace only the part(s) explicitly specified for your model
• Do not overtighten fittings; follow torque guidance from the appliance manufacturer
• If you smell gas or suspect a leak after installation, stop immediately

This orifice meters gas flow to a range or oven burner for consistent, controllable flames. Replacing a damaged or clogged orifice restores proper burner performance and helps maintain safe ignition and cooking. What it does

• Controls the gas flow to a specific burner for the correct flame size and heat output.
• Commonly replaces clogged, corroded, or damaged orifices that cause weak or uneven flames.
• Can resolve symptoms such as burners that won't light reliably, low flame, or irregular flame shape.
• Helps restore stable combustion when the flame is sputtering or lifting from the burner head.

• One gas burner orifice (single piece as shown)

• Turn off the appliance and shut off the gas supply before removing or installing the orifice.
• Use the correct-size wrench; avoid overtightening which can damage the fitting.
• Inspect threads and seat for debris; replace sealing gasket or use approved thread sealant per service manual if specified.