Dryer Turn Small Engine Ignition Coil Parts

This replacement gas valve controls gas flow to the burner in a gas dryer, enabling safe ignition and consistent heat. When it fails, the burner may not light and loads can stay damp; replacing it restores proper drying performance.

• Opens and closes gas flow to the burner when heat is called for
• Shuts off gas when the cycle ends or heating is not active
• Common symptoms: dryer runs but has no heat or the burner never ignites
• May present as the ignitor glowing or clicking repeatedly without flame, or intermittent heat

• Disconnect power and shut off the gas supply before servicing
• Work in a ventilated area and allow the dryer and burner to cool
• Use only gas-rated thread sealant on threaded connections
• After installation, turn on gas and check all joints for leaks with a soap-and-water solution

This gas dryer igniter assembly heats to a bright glow to light the burner so the dryer can produce heat. Replacing a cracked, weak, or non-glowing igniter restores reliable ignition and proper drying performance.

• Heats and ignites the gas at the burner to start the flame
• Restores drying heat when the original igniter is cracked or electrically open
• Common symptoms include: dryer runs but no heat, burner never lights, igniter does not glow, or extended dry times
• Visual damage such as white spots, breaks, or crumbling on the element indicates failure

• Disconnect power and shut off gas supply before servicing
• The igniter is brittle—handle only by the base or bracket; avoid touching the element with bare fingers
• Mount in the same position as the original and route leads away from heat and moving parts
• After reassembly, run a heat cycle to check the burner ignites; also check the flame sensor and gas valve coils

This gas valve includes the coils. For the coils alone use part number 279834

The Gas Valve Assembly is an OEM replacement part for LG gas dryers. It precisely controls the flow of gas to the burner unit during drying cycles. 

Symptoms of a faulty gas valve include: 

• Inadequate or inconsistent heating 
• Burner failure to ignite properly
• Error codes related to gas or pilot light issues

Causes may involve wear and tear of valve seals over extended use, blockages limiting gas flow, or damage like dents that compromise valve integrity.

This authentic LG assembly is compatible with select Kenmore brand models. 

This gas surface burner head distributes fuel through its ports to create an even, reliable flame on your cooktop. Replace a clogged, damaged, or warped head to restore consistent ignition and proper heat on the affected burner.

• Channels gas through precision ports to produce a steady, even flame
• Interfaces with the surface igniter/electrode for quick, reliable ignition
• Replaces worn or clogged heads that cause weak, uneven, or yellow flames
• Helps resolve delayed ignition or a burner that won't light

• Disconnect electrical power and shut off gas supply before servicing
• Remove grate and burner cap, lift off the old head, and clean the mating surface
• Align the new head with the igniter and locating features; seat it fully before replacing the cap
• Restore gas and power; test ignition and verify proper flame pattern

This burner assembly is the gas/air mixing and flame head for gas dryers. Replacing a warped or corroded burner restores reliable ignition and steady heat so loads dry evenly and cycle times return to normal.

• Mixes incoming gas with air and directs it to the igniter for proper light-off
• Produces a stable flame to heat the dryer's airflow
• Replaces burners that are bent, rusted, or clogged and affecting ignition
• Typical symptoms: no heat, burner won't light, intermittent heat, or long dry times

• Disconnect power, shut off gas, and allow the dryer to cool before servicing.
• Access the burner compartment; note component positions and wiring for reassembly.
• Protect the igniter and sensor mounted near the burner from impact.
• After reassembly, restore gas and check all connections with a leak-detection solution; verify proper ignition and flame.

For propane order 383EEL3002A.

This valve and pipe assembly regulates and routes fuel through the dryer's system so the burner can ignite and maintain heat. Replacing a failing assembly restores reliable heating performance and consistent drying results. What it does

• Opens and closes to control fuel flow to the burner when heat is called for
• Directs fuel from the inlet to the burner orifice through a rigid manifold/pipe
• Helps maintain safe shutoff when the dryer is idle
• Common symptoms of a failing assembly: no heat, intermittent heat, or burner failing to ignite

• One valve-and-pipe assembly

• Disconnect power and shut off the gas supply before servicing
• Use only gas-rated fittings/sealant as specified by the manufacturer; do not overtighten connections
• After installation, check all joints for leaks with a soap-and-water solution
• Restore power and gas, then verify proper burner ignition and stable heating

This glow-bar igniter lights the gas burner in your dryer so it can produce heat. When the igniter is cracked, weak, or open, the burner won't light and clothes won't dry properly.

• Heats up to ignite the gas burner during each heating cycle
• Common symptoms of failure: no heat, takes too long to dry, burner won't light, igniter doesn't glow or glows but no flame
• Restores consistent ignition and drying performance

• Unplug dryer and shut off gas supply before servicing
• Handle the igniter carefully—ceramic element is fragile; avoid touching it with bare fingers
• Note wire routing and burner alignment before removal
• After installation, restore gas/electric and check for proper burner ignition

Liquid propane to natural gas

This gas valve regulates and safely delivers fuel to your dryer's burner. When operating correctly, it opens for ignition and closes when heat is satisfied, providing consistent, reliable heating for effective drying.

• Opens to allow gas into the burner when the ignition system calls for heat
• Closes to stop gas flow during cycling or if ignition fails
• Possible symptoms: dryer runs but no heat; igniter glows yet no flame; intermittent heat or long dry times
• Helps restore proper burner ignition and stable flame

• Disconnect power and shut off the gas supply before servicing
• Work in a well-ventilated area; check all connections for leaks with a non-corrosive leak-detection solution after installation
• Transfer any brackets, fittings, or orifices from the original valve as required; secure connections
• Confirm gas type (natural/LP) and regulator/orifice settings per the service manual before restoring service

This Kit includes the Regulator Lock Limiter, the Main Orifice Spud and the instruction sheet.

This genuine OEM replacement part is a gas valve assembly for dryers. The burner and gas valve assembly is a complete assembly that contains the burner that distributes the gas in a way that creates an even flame allowing for heat to be distributed properly to perform the dryer's essential functions. If the dryer is no longer drying clothes effectively, or heating properly, then it might be time for it to be replaced. Luckily repairing a gas valve assembly is an easy fix.To replace the burner and gas valve assembly, begin by shutting off power to the appliance. Next, pull the dryer away from the wall to gain access to the back panel. Remove the back panel and locate the gas valve assembly. Remove the mounting screws that hold it in place. After removing the screws use both hands to pull and release the old valve assembly. Set it off to the side and proceed to install the new one by refastening the screws that hold it in place.This replacement part is sold individually and is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand washers.

This burner assembly restores proper gas flame and heat in your dryer. It directs and mixes gas and air for clean ignition at the igniter, helping clothes dry efficiently and consistently.

• Provides the flame path and mixing chamber for gas ignition
• Helps resolve symptoms like no heat, intermittent heat, or very long dry times
• Can address issues where the burner won't ignite or the flame will not stay lit
• Designed to fit the factory burner mount and align with the igniter and flame sensor

• Disconnect power and shut off gas supply before servicing; allow the appliance to cool
• Access is typically from the front lower panel or burner compartment
• Transfer any reusable hardware from the original assembly if required
• After reassembly, restore gas and check all connections for leaks using a soapy water solution

The Igniter is an OEM part for GE dryers. This part is responsible for generating a spark or glow that ignites the gas, producing the necessary heat to dry your clothes effectively. It ensures that the dryer reaches and maintains the desired temperature throughout the drying cycle.

A bad igniter can occur due to wear and tear, electrical malfunctions, or damage from excessive heat. If you notice symptoms such as the dryer not heating up, a lack of heat during the drying cycle, or the burner not igniting, it may be time to replace this part.

Symptoms of a bad igniter include:

• Dryer not heating up
• Lack of heat during the drying cycle
• Burner not igniting

Restore your GE dryer by replacing the faulty igniter with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This LP gas conversion label identifies that the appliance has been converted for use with liquid propane. Applying it near the gas valve/regulator clearly communicates fuel type for safe service, troubleshooting, and future installation decisions.

• Marks a converted unit as LP fuel to prevent misdiagnosis or incorrect hookups
• Provides quick visual identification for technicians and inspectors
• Replaces a missing, damaged, or illegible conversion label
• Use when a conversion has been completed and the original label is not present

• Apply only after completing the correct LP conversion procedure for your specific model
• Clean and dry the mounting surface; place the label where specified (typically near the gas valve/regulator or rating plate)
• Do not cover existing safety or rating labels; press firmly to ensure full adhesion
• Leak-check all fittings before returning the appliance to service