Washer Line Hook Line Mover Float Needle Parts

Noticed that lid lock light was not on, googled problem, ordered parts, working on 3rd day. Read more

The part is so new no video so I went onto a similar part and watched video that got me about 80%. Then, called and customer service sent me a service Manual but this still was not specific so I broke the old to get it out and in the process figured out how to do it correctly. So I installed the last bit of it which was the bezel through the machine top by myself correctly. So you take the old one out by pushing out to the right from the bottom side using a screw driver for leverage. It will... Read more

• Lid or door won't close
• Won't start

Not wanting to spend hundreds of dollars on an appliance technician's service call, I searched online to troubleshoot the problems with my particular Maytag Washer Model Number MVWX500BW0. I stumbled across AppliancePartsPros.com and investigated there the most likely causes for my Maytag Washer's not agitating properly and not spinning at all. In order to acquire some additional information, I telephoned AppliancePartsPros.com and spoke with an extremely professional, knowledgeable and helpful... Read more

• Won't start
• Lid or door won't close
• Door latch failure
• Will not agitate

Superfast parts delivery. Got packages by the second day. Videos were extremely helpful and well done; we couldn't have done without them although we came across slight differences in our machine and found workarounds. Our machine did not drain the water so I drained the water manually via drain tube at bottom of the machine and checked the filter for blockage. All clear so I read articles on the internet and watched videos and took a chance on replacing the drain pump and circulating motor... Read more

• Lid or door won't close

This was a super-easy repair. You have to line up the spring so that it sits on the bumps inside the magnet holder and the door, then you have to line up the tabs on the magnet holder so they will slide into the slots on the door. Then you just push it in. Repair took less than a minute. Read more

I ran a diagnostics check on the washing machine and came up with the error code E47 -Board thinks the door PTC circuit is open in spin. The washer thought the door was open and would not finish the spin. I was left with a washer full of very wet clothes. This repair was SO extremely easy. I only needed to uses a pair of needle nose pliers and a screw driver. It took less than 10 minutes, start to finish. Now the new door lock assembly registers correctly and my clothes are completely... Read more

Unscrewed door latch and replaced it with the new door latch (1-2 min). Unscrewed outer plate from door lock assembly. Removed door lock assembly from its outer plate and unplugged wiring. Replaced with new door lock assembly, plugged back in, tightened some screws, double-checked alignment between latch & lock assembly was good and the project was done. Incredibly easy and saved about $150 not having a repair tech come out to fix it. Read more

• Lid or door will not open
• Won't start
• Lid or door won't close

Just removed the old and put on the new,simple.On this Fridgidare washer you should lift the door as you close it which should make the striker last.. Read more

Replaced the door latch/lock assembly. Read more

Replaced door lock switch. Read more

Ordered parts from Appliance Parts Pros and replaced them.Works like new Read more

The part is so new no video so I went onto a similar part and watched video that got me about 80%. Then, called and customer service sent me a service Manual but this still was not specific so I broke the old to get it out and in the process figured out how to do it correctly. So I installed the last bit of it which was the bezel through the machine top by myself correctly. So you take the old one out by pushing out to the right from the bottom side using a screw driver for leverage. It will... Read more

Replaced it. Read more

• Won't start
• Lid or door will not open
• Lid or door won't close
• Will not agitate

The washing machine would allow you to program it, and all the lights on the control panel would light up, but pressing start did nothing. I tried putting the washer in diagnostic mode, but was unable to do so. The machine was not showing any fault code. I originally thought it was a problem with the 'Start' button and I thought that I'd buy a replacement part from the original seller of the washer. I was told by the 'live help chat person' that the problem was likely in the washer user... Read more

• Lid or door will not open
• Won't start

Did lots of internet research. Narrowed problem down to three things - door lock latch, control unit, and motor control unit. Figured out how to run the diagnostic test program, which showed a F22 (door lock) error. Removed and ohm tested the door lock (pins 1 & 3). Found door lock latch to be defective. ordered new one and installed it. YouTube video helped a lot. https://www.youtube.com/watch?v=_SjU6k5bpSs So far, so good. Have only done a few loads. New door lock latch tested fine. Read more