79635123210 Parts

The Motor Rotor Assembly is an OEM part for LG washing machines. This component is crucial for the washer's motor operation, as it works in conjunction with the stator to create the electromagnetic field that drives the drum. It ensures the drum rotates effectively during the wash and spin cycles, facilitating thorough cleaning and efficient water extraction.

Over time, the motor rotor assembly can wear out or become damaged due to regular use, exposure to water, or excessive loads. Causes of a bad motor rotor assembly include bearing failure, corrosion, physical damage, or electrical issues.

Symptoms of a bad motor rotor assembly include:

• The washer not spinning or agitating
• Unusual noises such as grinding or squealing during operation
• The drum not turning or rotating inconsistently
• Error codes related to motor issues

This OEM LG part is also compatible with Sears/Kenmore.

This replacement door hinge restores smooth, aligned opening and closing. Replacing a worn or bent hinge helps the door sit squarely and seal or latch properly, preventing rubbing, binding, and premature wear on adjoining parts. What it does:

• Supports and pivots the door for smooth operation
• Maintains door alignment for proper latch/seal engagement
• Replaces bent, cracked, or loose hinges that affect door movement
• Common symptoms include door sagging, rubbing/binding, difficulty closing, or visible hinge damage

• One door hinge

• Disconnect power before servicing; remove door contents to reduce weight
• Support the door while removing hinge fasteners to prevent strain on the new part
• Transfer and reuse original hardware as required; tighten screws to manufacturer-recommended snugness
• Verify door alignment and operation after installation and adjust as needed

This dispenser assembly is the washer's detergent drawer housing. It channels incoming water through the detergent and fabric softener compartments (and prewash, if equipped) so additives are dispensed at the correct time and helps prevent leaks at the dispenser area.

• Directs water through the dispenser to flush detergent/softener into the tub at the proper points in the cycle
• Replaces cracked, warped, or clogged housings that leak or misdirect water
• Helps resolve detergent or softener remaining in the drawer after a cycle
• Addresses water leaking or overflowing from the dispenser area or visible damage/mineral buildup in the dispenser box

• Unplug the washer and shut off water supplies before servicing
• Pull out the drawer, remove the top cover as needed, then remove mounting screws and release hose clamps to detach the old assembly
• Move hoses/clamps to the new assembly and ensure gaskets/siphon caps are properly seated
• Run a quick fill/rinse to check for leaks before final reassembly

This hardware washer sits beneath a screw or nut to spread load and help keep fasteners tight inside your appliance. Replacing a bent or missing washer restores a secure fit and can reduce vibration-related noise. What it does:

• Distributes clamping force to protect mounting surfaces
• Helps resist loosening from vibration and movement
• Restores proper alignment when a washer is damaged or missing
• Common symptoms: loose or wobbling parts, rattling noises, screws backing out

• 1 washer

• Disconnect power; if working on a washer, also turn off water supply
• Note the original hardware stack order and take photos for reference
• Place the washer between the fastener head or nut and the part being secured
• Tighten to manufacturer guidance; avoid overtightening to prevent damage

The Hose Assembly & Connector is an OEM part for LG washing machines. This assembly includes the hose and connector, which are essential for supplying water to the washer during operation, ensuring a steady and reliable flow.

Causes of a bad hose assembly and connector can include wear and tear over time, cracks or splits due to pressure or temperature changes, and damage from improper installation or handling. 

Symptoms of a bad Hose Assembly & Connector include:

• Water leaks from the hose or connector
• Low water pressure or flow to the washer
• Visible cracks or splits on the hose
• Water not entering the washing machine properly

This OEM LG part is also compatible with some Kenmore models.

This inlet hose routes incoming water from the washer's fill valve into the machine to support proper filling. Replace a cracked or leaking hose to stop drips, prevent water damage, and restore reliable fill performance.

• Directs incoming water from the fill valve to the dispenser/tub during wash cycles
• Maintains a sealed path to prevent internal or external leaks
• Helps the washer reach proper fill levels and timing
• Common symptoms of failure: water on the floor, leaks during fill, visible cracks or bulges, long/no fill or IE error

• Unplug the washer and turn off both hot and cold water supplies
• Keep towels or a pan handy; relieve residual water pressure before disconnecting
• Note the original routing; fully seat the hose on fittings and secure with existing clamps
• Restore water and power, then run a quick fill to check for leaks

This switch assembly is the microwave's door interlock module. It mounts to the latch board and contains the switches that confirm the door is closed, restoring consistent start/stop operation when worn or sticking switches cause intermittent "door" errors.

• Houses and positions the interlock micro-switches on the latch board
• Signals the control that the door is securely closed so the unit can run
• Common fixes for: won't start, stops when the door is jostled, "door" error messages, or runs but doesn't heat
• Helps correct intermittent operation caused by fatigued or misaligned switches

• Disconnect power before servicing; microwaves retain dangerous high voltage
• Remove the upper grille and control panel to access the latch area per your model
• Note wire locations and switch orientation; move connectors one at a time to the new assembly
• After installation, verify door latching and test operation before reassembly

The Softener Cap is an OEM part for LG washing machines. It serves as the lid and housing for the internal water softener that prevents mineral deposits from building up. The softener cap funnels water to and from the softener compartment during various stages of the wash cycle.

Causes of a faulty softener cap can include cracked or degraded seals over extended usage, impact damage distorting fit, or harsh cleaners affecting plastics over time.

Symptoms of a bad softener cap include:

• Water leaks from around the softener area  
• The cap not closing or sealing properly 
• Mineral buildup occurring prematurely
• The softener not functioning as intended

This genuine LG replacement is compatible with Sears/Kenmore machines.

This washer motor stator assembly is the stationary windings of the direct-drive motor. Replacing a weak or shorted stator restores smooth drum tumbling and strong, consistent spin performance so wash cycles complete properly.

• Creates the rotating magnetic field that drives the rotor and spins the inner basket
• Works with the rotor to provide torque for wash/tumble and high-speed spin
• Common symptoms: drum won't spin or tumble, stops under load, or motor hums without turning
• Burnt odor or visible heat damage on windings can indicate stator failure

• Disconnect power and turn off water; access the motor from the rear panel
• Remove the rotor center bolt and slide off the rotor; strong magnets—handle carefully
• Unbolt and remove the stator; transfer/reconnect the motor position (Hall) sensor and harness if present
• Tighten fasteners evenly; verify drum rotates freely by hand before restoring power

The Top Load Washer Coupling Assembly is an OEM component specifically designed for LG brand top-loading washing machines. This assembly connects the agitator shaft to the transmission inside the washer, allowing oscillating motions to be transferred through the transmission from the motor. 

Symptoms include:  

• No agitator movement or flickering motions during wash cycles
• Grinding or clicking noises coming from the motor/transmission area
• Leaks or loose fluid from damaged housing components  
• Shaking or instability of the entire washing machine

Causes of a bad coupling assembly can include material failure from ongoing vibration exposure, loosened connection points allowing unwanted play, or cracks/breaks due to heavy impacts.

The Motor Stator Bolt is an OEM part for LG washing machines. This bolt secures the stator to the motor, ensuring the stability and proper functioning of the washing machine's motor assembly.

Causes of a bad motor stator bolt can include wear and tear over time, improper installation, or damage from over-tightening or impact. A compromised bolt can lead to instability in the motor, potentially affecting the washer's performance.

Symptoms of a bad motor stator bolt include:

• Unusual noises during the wash cycle
• Vibrations or shaking of the washer
• The motor not functioning properly or failing to start

This OEM LG part is also compatible with Sears/Kenmore.

This factory assembly bundles the small components required to restore a specific sub-assembly in your appliance, helping bring back proper fit, alignment, and reliable operation without hunting for individual pieces.

• Replaces a worn, broken, or missing small assembly so the connected component mounts and moves correctly
• Can help resolve looseness, rattling/clicking noises, misalignment, or parts not staying in place
• Designed to match the original geometry for consistent, long-term performance
• Restores proper operation after physical damage, stripped hardware, or fatigue of clips/fasteners

• Disconnect power and, if applicable, shut off water or gas before service
• Work from your model's diagram to match part orientation and fastener locations
• Keep track of small pieces; take photos during disassembly for reference
• After installation, verify smooth operation and secure fit before full use

This rotor assembly is the rotating half of the direct-drive motor in your washer. It mates with the stator to spin and agitate the basket, restoring drive when the original rotor is worn, cracked, or stripped.

• Forms the magnetic rotor of the direct-drive motor to turn the wash basket
• Transfers motor torque directly to the tub for spin and wash action
• Common symptoms: no spin or agitation, starts then stops, loud grinding/clicking, motor-related error
• Visible damage may include cracked hub, stripped splines, or loose fit on the shaft

• Disconnect power and water; wear gloves and eye protection
• Access from the rear, remove the back panel, hold the basket, then remove the center bolt and pull the rotor straight off (strong magnets)
• Align splines/keyway, seat the rotor fully, and reinstall/tighten the center bolt securely
• Inspect the stator and hall sensor for damage before reassembly and test a spin cycle

This genuine hardware washer installs at the specific joint shown in your model's parts diagram. It spreads clamp force and keeps the connection aligned and secure to support smooth operation of the related component. What it does:

• Distributes fastener load and protects mating surfaces from damage
• Maintains proper spacing and alignment within the assembly
• Helps resist loosening from vibration over time
• Clues it may be needed or worn: loose/rattling parts, unusual vibration or noise, or visible wear at the fastener location; on some models, seepage at that joint

• 1 washer

• Disconnect power and turn off water supply before servicing
• Support the assembly, remove the fastener, and install the washer in the same orientation
• Tighten the fastener snugly without overtightening; replace any damaged bolts, nuts, or seals

The balancer assembly mounts to the washer's basket/tub to counterbalance loads during spin. When worn or damaged, it can cause shaking, banging, or out-of-balance errors. Replacing it helps restore smoother, quieter spin performance.

• Stabilizes the basket/tub during acceleration and high-speed spin
• Helps reduce vibration, banging, and washer "walking"
• Can prevent spin cycles from slowing or stopping due to imbalance

• Disconnect power and allow moving parts to stop before servicing
• Access is typically at the top of the tub/basket under the tub ring; remove covers as needed
• Note orientation; seat the assembly evenly and ensure all tabs/fasteners are fully engaged
• After reassembly, run an empty spin test to verify smooth operation

The Dispenser Assembly is an OEM part for LG washing machines. This part dispenses the appropriate amounts of detergent, fabric softener, or other laundry additives at the right time during the wash cycle.

Causes of a bad Dispenser Assembly can include clogging or buildup of residue, damage to the dispensing mechanisms or components, or issues with the electronic controls that regulate the dispensing process.

Symptoms of a bad washer Dispenser Assembly include:

• Improper dispensing of detergent or fabric softener
• Leaks or drips from the dispenser area
• The dispenser drawer not opening or closing properly
• Failure of the dispenser to dispense at the correct time during the cycle

This OEM LG part is also compatible with some Kenmore models.