Kenmore 41744052400 Parts

I ran a diagnostics check on the washing machine and came up with the error code E47 -Board thinks the door PTC circuit is open in spin. The washer thought the door was open and would not finish the spin. I was left with a washer full of very wet clothes. This repair was SO extremely easy. I only needed to uses a pair of needle nose pliers and a screw driver. It took less than 10 minutes, start to finish. Now the new door lock assembly registers correctly and my clothes are completely... Read more

• Will not drain
• Noisy

So, Saturday, the washer wouldn't drain, yes, I tried the Drain/Spin cycle. So I took the clothes out, rinsed them out twice in the laundry sink and dried them. After a quick Google search, I came to the conclusion that the pump was bad and ordered a pump, $125. Over the course of the next four days, expecting the new pump on Thursday, I baled out the washer, pulled it out from the wall and propped up the front (it's HEAVY), removed the front access panel, removed the drain inlet and outlet... Read more

• Shakes and moves
• Noisy

I watched the video posted by Jerrod Sessler on yellow van handyman.com. Then I had to unstack the dryer from the washer, remove all covers, disconnect all hose connections, shock mounts and springs and remove the tub assembly. Then I disassembled the tub assembly and remove seal and both bearings from the rear half. At this point I cleaned everything. I installed new bearings and seal, installed the basket and assembled both tub halves using a new gasket and silicone, and reinstalled the... Read more

• Leaking

Fixed by replacing the washer door seal "Bellows". Once again AppliancePartsPros comes through with the right part at a great price. It took quite some time to install because putting the inside spring back on the bellow was difficult so I needed to remove the top and front door of the washer to get better access. A set of 3 or 4 plumbing clamps are highly recommended to get that spring back on (I went to the store and bought some). If you search YouTube about replacing the bellows on your... Read more

• No hot or cold water
• Will not stop filling with water

It was really easy to fix. I just took a screw driver and gently pried up on the top of the clothes washer to open up the top. Then the mixing valve was easy to access. I removed the two screws holding and unplugged the the wires. And pulled the old one free. Then reversed the process to install the old one. Less than thirty minutes start to finish. Read more

• Leaking

Y'all! This video made fixing my washer easy peasy. The service repair man wanted $352! I paid less than $200 for the parts. I also called around and appliance parts pros was by far the cheapest option. The shipping was unbelievably fast. (Faster than my amazon prime!) Read more

Got online and searched for part by washer model number. Found AppliancePartsPro.com. They listed diagram of part. I ordered it online and received it next day with no extra charge for fast delivery. My husband attached cosmetic drawer cover to detergent drawer part we ordered in a few minutes. It fits and is working! Speedy service was appreciated. Read more

This was the motor control board (also called the speed control board, motor control unit, or MCU in various places across the web). The repair was straightforward, except for two complications. First the old part was difficult to access in this model washer (Frigidaire Gallery Series front load washer). Instead of being easy to reach on the left side where there was space, it was sort of behind the actual motor on the right side of the housing. I spent some time trying to figure out... Read more

• Shakes and moves

With more difficulty and frustration than expected but it works fine now. Things learned: 1. Order only 3 replacement pins. One comes with the shocks that you can't be sure you see in the picture. 2. A circuit board in a plastic box mounted to the floor, left rear, must be removed by two screws to be able to get pliers onto the head of the pin more easily. This helps installation too. 3. A 1/2" deep socket pushed onto the retaining tab of the pin stays there while you pull with pliers from the... Read more

Watched the video a few times for door boot seal replacement. It was a lot of help! The spring is the hardest to replace and I did enlist the help of my wife. Everything went back on great. If you have to replace the front panel (with the buttons) be mindful that the buttons are spring loaded and will come out. I did not lose any and it went back together just fine. A little touch up paint on the washer and it all looks brand new and works great. And the parts came in quicker than... Read more

Our washing machine door boot seal was getting moldy and causing odor problems. Cleaning tablets and bleach weren't helping so it was time to be replaced. While I had the top and front off I changed all the hoses that could be collecting soap scum and mold, all other wetted parts were removed and washed. The video on the door boot seal, and inlet valve assembly were extremely helpful in understanding how these parts are removed and reassembled. Although the door boot seal is the most visible... Read more

It was easy to find the part on appliance parts pros. Once I found it I studied the diagram and determined that there were 3 screws in the drum that needed to be removed. I disconnected power and then removed 3 interior screws. Once I did that I removed the back cover and removed the single screw on the bottom side of the air duct that held it in place connected to the heat tube. I then reversed disassembly. I want to tell you this is a 2 person job. In order to assemble it you need to... Read more

First of all, I want to say that this is not the first time that I have used AppliancePartsPros. They give you everything you need in the most simplified manner to repair your appliances at home. I ran my washer until I started to see the leak coming from underneath. After verifying that the intake hoses, drain hose and pump were not leaking, I opened up the washer from the top by unscrewing the two screws on the back brackets and lifting up and out. Because the leak was displaying at the... Read more

After examining it, 2 of the 4 retainer clips had broken off. My wife grabbed her tablet, found Appliance Parts Pros website, saw 2 videos featuring our exact model of washer and ordered the 3 parts to replace broken and soon to fail parts ! Shipping was extremely fast ! Took out old assembly, replaced with new assembly in about 15-30 second, wife was happy, therefore I was happy ! Thx for being there ! Read more

Unscrewed the front lower panel ( 2 screws ). Disconnected the pump hose clamp and removed the hose. I loosened the lower back panel and pulled out the drained hose from the rear. Replaced with new hose put back clamp and panels. Very easy Read more