Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Dishwasher won't start or run? A faulty door latch prevents cycles from beginning. This latch assembly secures the door and activates switches. 5-10 min fix.
After I double checked that the unit did have power to it, I concluded it was probably a switch or the User Interface Board. I found the parts on the AppliancePartsPros for the best price and delivery. After the parts were delivered two days later, it took me a couple hours to disassemble and re-assemble the door for the dishwasher and luckily everything seems to be working fine three days and three loads later. The only issue I had was with the User Interface board..... this is a generic... Read more
Dishes not drying or staying wet after cycle? This heating element heats water during wash and dries dishes after rinse. DIY-friendly replacement part.
I followed the directions on several websites for repairs. The obvious place to start is the heating coil and thermostat. I checked the continuity of the coil and it was good with a reading of almost zero resistance. Next I read that there is no thermostat controls on my GE dishwasher so I followed another webpage that said the Sensor Turbidity Assembly acts like a thermostat so I replaced that. Wasted effort as that switch sensor was OK. Normally it has a light on when it is working, a... Read more
Fix a dishwasher that won't fill with water by replacing the flood switch assembly. This 5-minute DIY repair detects water levels to prevent flooding.
Removed the lower rack, removed the lower wash arm, removed the lower coarse filter, removed fine filter ( still no tools require to this point). Removed two 1/4" head screws with nut driver to then remove float switch, unplugged float switch, plugged in new switch, reinstalled filter, etc. This is a 5 minut job! Read more
The Single Speed Dishwasher Drain Pump Kit is an OEM replacement part for GE dishwashers. This important part works to drain water from the dishwasher at the end of each cycle. The pump ensures water is fully drained from the tub and pipes to prevent damage. Causes of a bad drain pump can include normal wear and tear over extended use, blockages in the drain system, or failures in the electric motor. Symptoms of a bad drain pump include:
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
I viewed youtube videos and followed the instructions on how to determine the cause of the problem. I cleared the lines and poked my fingers in to check for obstructions. But in the end, the drain pump was the problem. The pump came in the mail the next day. The job required the pump and only one of the hose clamps as the original setup has one single ear clamp which can be removed with wire cutters and a standard one which I re-used. There is a wire adapter in the kit that is necessary to... Read more
Replaces broken or worn lower rack carriers and rollers. Installs on both sides of the dishwasher lower rack to restore smooth gliding along tracks.
I was able to find the parts on your website. I was a little worried because there were no photos, but the parts were correct, and it was an easy fix! Read more
Seals the dishwasher tub opening to prevent water leaks during wash cycles. Replace if worn, flattened, or causing leaks. Verify fit with your model.
Upon taking the door apart it looked like the leak was coming from the vent so I replaced the vent cap, vent seal and the transition piece. I did not have to change the seals. It took me a while to figure out how to get the door apart, but once I did, it was fairly straightforward. Read more
The Lower Rack Roller is an OEM replacement part for GE dishwashers. This small but crucial component allows for smooth and effortless movement of the lower dish rack during loading and unloading.
Symptoms of needing to replace the lower rack roller include:
Causes of a faulty lower rack roller can include normal wear and tear over time, exposure to heat or moisture, or physical damage due to impact or mishandling.
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore dishwasher models.
The Circulation Pump is an OEM part for GE dishwashers. It is responsible for circulating water throughout the dishwasher. It pumps water from the bottom of the dishwasher and directs it to the spray arms, allowing for distribution of water and detergent to the dishes.
A bad Circulation Pump Kit can occur due to wear and tear over time, clogs or blockages in the pump, or electrical malfunctions.
Symptoms of a bad Circulation Pump include:
This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.
We pulled the dishwasher out, took it to the garage and set it up on sawhorses and planks so we could access the bottom. We plugged it in and filled it with water and ran a quick cycle. As soon as the circulation pump kicked on water came spraying out from the rubber boot in the diverter assembly. It appears that there was a factory defect in the hose. Unfortunately, the water got into the pump motor over a few loads and was eroding the brushes on the motor. We decided to replace it as well.... Read more
Replacement silverware basket for dishwasher lower rack. Holds and organizes utensils during wash cycles. Order if your basket is cracked or broken.
Replaced Side blaster Read more
Upper dishrack rail for dishwashers. Allows the top rack to slide in and out smoothly. Replace if cracked, broken, or bearings are worn or missing.
Replaced the upper rack inner rail assembly. Read more
The Service Machine Control is an OEM part for GE dishwashers. This part oversees and manages the various functions and cycles of the appliance. Acting as the brain of the dishwasher, this control unit receives input from the user and sensors throughout the machine, then directs operations such as water intake, temperature regulation, cycle duration, and drying processes. Causes of a bad Service Machine Control can include power surges, moisture exposure, or physical damage to the circuitry. Symptoms of a bad Service Machine Control include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
Ignore the blogs that say the code is either for the door switch or the main control board. Just buy both of them because it is cheaper than a new dishwasher. Easy as Read more
Seals dishwasher tub edges to cabinet, preventing leaks and debris entry. Replace if worn, cracked, or missing for proper seal. Verify fit with model.
Diagnosed problem with UI fail / Personality lost from service manual. Replaced UI board with only one hiccup. (Mixed up personality jumpers) New board requires personality to be set specific to the model number. Board will not function correctly, if al all, if the personality jumpers are not set exactly to your model. Read more
Controls airflow in your dishwasher door. Replace if cracked or if you see leaking from the door vent area. Confirm fit with your model number.
Secures the folding tine row on your dishwasher's lower rack. Replace this clip if it's broken, cracked, or missing to keep adjustable tines stable.
Replaced all movable parts. Read more
Secures your dishwasher underneath the kitchen countertop. Replace if the bracket is cracked, broken, bent, or missing from installation.
Order parts from Appliance Parts Pros. Read more
If your dishwasher's bottom rack has broken or cracked tines, this folding tine row restores proper dish support. Simple snap-in repair, typically under 10 minutes.
Ordered parts for new back tines for the lower rack from AppliancePartsPros.com. Removed old damaged tines and replaced them with new ones. Very simple repair. Read more