Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Get your dryer spinning smoothly again - install the Whirlpool 341241 OEM Drum Belt in minutes.
Unpluged dryer first. Then took the lint filter out and removed the two philips screws inside the lint filter lid. Then take a paint scraper just under the top of the dryer two inches from the left front corner and pushed in a little to release the snap connector and did the same on the right side. Then lifted top over. Then take a 5/16 socket or nut driver and remove the two screws on on the left inside panel, then the right side. Lean front out a little and remove the two wires one the back... Read more
Dryer won't heat or flame shuts off after 15 seconds? Gas valve coils control gas flow to the burner. Takes about 30 minutes to replace both coils.
I'm starting with a quick background on my dryer. About 18 months ago the belt on the dryer started slipping and squealing. I had a can of belt dressing spray so I popped the top open and sprayed the belt. It actually worked for about a year before it started squealing again. For the next 6 months I had to spray it more and more often. Then the clothes stopped drying. Obviously, at this point, I had to get off my lazy ass and fix the dryer. Searched my dryer's model number on the internet and... Read more
Captures lint and debris from laundry to prevent vent clogs. Replace if torn, cracked, or clothes snag on it. Confirm fit with your model number.
The original issue with the dryer is that a corner of the lint screen was sticking out of the lint screen guide, and it would not stay flush with the guide. As a result, many tank top straps, waistband strings, and blankets would get caught on this corner and twist, tear, or warp my clothes. When I did my research on the issue, I kept reading that it was an issue with the lint screen that came with the dryer. So I ordered the lint screen, guide, and cover that appliance part pros recommends to... Read more
Drum support roller assembly for dryers. Installs inside the cabinet to support the drum during rotation. Replace when worn, flat-spotted, or broken.
I consulted with the internet and your website and determined I had a bad roller wheel. I was going to buy just one but determined if you have to take the thing apart, just replace all of them. These lasted 10 years after all. Opened up You Tube for the method to take the dryer apart. After doing the washer last year, I felt pretty bold and just ripped into the project. Within 30 minutes I had the drum out and located the problem wheel ( rear right side). It was locked up due to hair build up... Read more
Connects the motor to the drum so it can tumble. Replace if the drum won't spin, makes squealing noises, or clothes aren't drying. Confirm fit by model number.
I disassembled/reassembled the dryer according to the ApplianceParts Youtube video. With my limited electrical knowledge (just enough to be dangerous) I initially figured it was a problem with the heating unit, sensor(s), or the control board. After diagnosing the problem (bad thermistor), I had to order the parts and was able to repair and reassemble the dryer several days later. After removing the drum, I cleaned all the dust etc. out of the inside (it gets dirty in there!) and inspected,... Read more
Houses the lint filter to capture debris during drying. Replace if cracked, causing clothes to snag or tear. Confirm fit with your model number.
I replaced the warped cover guide and the lint filter. Now it works perfect! Sears was going to charge $100 just to diagnose the well known problem, not including parts and labor. It only requires 4 screws(i used the old ones). Easy fix. Read more
Connects the motor to the drum for tumbling. Replace when stretched, worn, or broken causing the drum not to turn. Confirm fit with your model number.
I went to the local Home Depot and Lowes, but they did not have the parts because they do not carry parts for the items they actually sell to people. Jumped on the phone and did a quick search for parts and came across appliancepartspros.com. I put in the make and model of my dryer and all the parts for the dryer where listed. I ordered the items on a Wednesday night. I opted for the two day shipping. I thought the items would be at my house by Friday but they did not arrive until Monday. I... Read more
Dryer won't heat or flame goes out after ignition? The flame sensor monitors burner flame presence. Common DIY fix with multimeter testing required.
I used Fixya as an initial source describing my problem. I got two responses which were very helpful. One that the "coils" were probably the problem. Two, that the problem could be the thermostat or a thermistor in the dryer. I verified that AC was coming from the timing control, that both the two terminal and three terminal coils,the igniter and shut off thermostat all had continuity. I then applied AC directly to the coils: the two terminal coil ""clanked" and I interpreted that as the coil... Read more
Dryer not heating or shutting off mid-cycle? A faulty blower thermostat disrupts airflow regulation. Front-access repair with basic tools in 30-60 minutes.
Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more
Dryer not sensing when clothes are dry? Replace the moisture sensor bar to restore auto-dry cycles. Moderate DIY repair with video guide available.
After I cleaned out the typical 1.5 pounds of lint from the vent, ( I do it every 2 months), I went searching for a solution. I found 6 possible causes on this site and purchased everything except a new burner; I wasn't going to go that far. Let the fun begin. Since my vacuum was still nearby, I thought I was ready for anything. Wrong. After I watched all the videos again for reassurance, I went in with screwdriver in hand and laptop nearby. I removed the top and looked inside. Don't be fooled,... Read more
This roller supports and stabilizes the dryer drum as it rotates. Replace if worn, cracked, or causing noise during operation. Installs behind the drum.
I pulled the dryer away from the wall and unplugged it. Then I used a 5/16 nut driver and removed the 2 screws in the bottom front panel and pulled it off. Next I removed the 2 5/16 screws holding the front door panel and pulled it down far enough to disconnect the wires for the light and the wires on the door switch. Then , using a putty knife I popped the springs holding the top and control panel then pulling the top up and resting it against the wall. Now I started my repair by laying on... Read more
Secures the lint filter in proper position to prevent clothes snagging. Replace if cracked, warped, or filter sits unevenly. Confirm fit with your model.
Captures lint and debris during drying cycles. Replace when the seal becomes compressed or frame cracks to maintain efficiency and prevent vent clogs.
We had a problem of lint building up inside of the filter slot. Once I took a long brush and cleaned the recess where the filter slides I was able to see that the old filter was not catching all the lint. Upon closer examination I noticed that the seal around the filter had become compressed. that's when I order another filter from AppliancePartsPros.com. My new filter came within three days and my dryer has been working fine ever since then. Read more
Replacement dryer lint filter guide cover. Installs over the lint screen housing to prevent small items from entering the duct. Replaces cracked covers.
I have order three parts, guide filter, cover guide, and sensor assembly. My previous cover guide was from two parts, when sensor assembly was one of them. New part ( guide cover ) was all in one piece so I just transfer old metal part of sensor to new cover guide and I don't need that sensor assembly anymore. I have ordered all three parts overnight by Fedex, ordered 15 min before 5pm, so next day it was here. Dryer is fixed, I'm happy. Read more
Maintains tension on your dryer's drum belt for smooth rotation. Replace if pulley wheel is cracked, shaft worn, or assembly moves excessively during operation.
Was going to order 4 new wheel & spindle sets, then saw you could get just the wheel for 1/3 the cost, so I ordered those. Then in the frequently ordered other items I saw the idler wheel assy. So I ordered one of those also. Glad I did, it was in worse shape than any of the wheels which still seemed to spin freely after I got all the hairs and crap off them. Anyways, went by the video step by step. Pretty straightforward. Have a good vacuum handy, I’m surprised that it used to dry at all... Read more
Dryer lint filter screen traps lint and debris during drying cycles. Replace if cracked, damaged, or lost to maintain airflow and efficiency.
I purchased a new replacement. Read more