Dvm3160 Parts

The Hood Damper Assembly is an OEM part for GE microwave ovens. This part controls the flow of exhaust air to minimize odors and smoke from cooking. This damper opens to allow air to vent outside during microwave operation and closes to prevent outside air from entering when the microwave is not in use.

Causes of a bad hood damper assembly can include mechanical failure such as a stuck or broken damper, deterioration of the linkage or springs that operate the damper, and blockage caused by grease or debris accumulation, which can impair its functionality.

Symptoms of a bad Hood Damper Assembly include:

• Ineffective venting of smoke or cooking odors
• External air leakage into the microwave system
• Unusual noises during operation indicating a damper misalignment or obstruction

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This vent grille covers the upper front opening of the microwave and channels exhaust air through the louvered slots. Replace a cracked, loose, or missing grille to maintain proper ventilation and restore the unit's finished appearance.

• Directs exhaust airflow while allowing adequate ventilation
• Shields internal components at the upper front of the microwave
• Provides a clean, finished look when secured in place
• Typical symptoms: broken or missing louvers, loose fit, rattling noise, grille won't stay secured

• Disconnect power to the microwave before servicing
• Remove and retain mounting screws; support the grille as the last fastener is removed
• Transfer any reusable clips or nameplate from the old grille if present
• Align the new grille and start screws by hand; tighten gently to avoid cracking

The Installation Hardware kit is an OEM part for GE Built-In and Over-the-Range microwaves. It contains all mounting screws and brackets needed for installation into upper kitchen cabinetry. 

Symptoms of faulty or inadequate hardware include:

• Loosening or failure of the microwave mounting over time
• Difficulty leveling or properly securing the appliance
• Warping or damage to cabinet surfaces from faulty bracketry

Causes can be stripped screw holes, worn brackets, or omitted/lost original hardware disrupting a snug fit. Replacing with this hardware ensures safe support of weighty microwaves above cooktops.

Compatible with GE Profile, Hotpoint, and some Kenmore units, it facilitates installation or re-installation without frustration. 
 

The Magnetron is an OEM part for GE microwaves. The magnetron converts electrical energy into microwave radiation, which heats and cooks the food placed inside the microwave oven.

Over time, the magnetron can wear out or fail due to regular use, electrical surges, or overheating. A malfunctioning magnetron can lead to the microwave not heating properly, reducing its overall functionality and efficiency.

Symptoms of a bad magnetron include:

• The microwave not heating food at all
• Unusual noises such as buzzing or humming during operation
• A burning smell or visible damage inside the microwave
• The microwave turning on but failing to heat

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This thermostat switch is a temperature-sensitive safety device used in select appliances to open or close an electrical circuit at a set temperature. Replacing a failed switch helps restore proper temperature control and protects components from overheating.

• Monitors temperature and changes state (open/closed) at its calibration point
• Helps prevent overheating or incorrect temperature regulation
• Common failure signs: no heat/overheating, intermittent cycling, or unit shutting off prematurely
• May be mounted to a bracket or surface near the heated area, depending on the model

• Disconnect power before servicing; verify no voltage is present
• Note wire positions and orientation of the original switch before removal
• Transfer any mounting hardware from the old part if not reusable
• After installation, test operation and observe initial heating cycle for proper function

This charcoal filter is used on microwave ovens to filter grease and other air contaminants during cooking. This filter contains charcoal for added filtering and is not washable. When the filter becomes clogged, it must be removed and replaced. If the air filter is clogged, smoke and fumes will not be cleaned, and the room will fill with odors during cooking. The charcoal filter catches grease spatters, and if greasy foods are cooked often, the filter will need to be changed more often. The filter should be removed and replaced regularly and anytime that it is not working efficiently. Removing the filter does not require tools. Pull the old filter straight out and push the new one in place.This charcoal filter is a silver metallic part that is sold individually. It is designed for use in microwave ovens designed by General Electric.

This turntable motor drives the coupler and glass tray in your microwave, rotating food for more even heating. Replace a failed or noisy motor to restore smooth, consistent tray movement and reduce cold spots during cooking and reheating.

• Drives the center coupler and glass tray to rotate during operation
• Helps ensure even heating by moving food through the microwave energy field
• Direct replacement when the original motor is seized, noisy, or electrically open
• Symptoms include a tray that won't turn, jerky rotation, or a humming/grinding sound from the turntable area

• Disconnect power before servicing; microwaves contain high-voltage components that can retain a dangerous charge
• Access to the motor is typically from the bottom; remove the cover/panel per your model's service information
• Transfer the two wires to the new motor and secure it with the mounting screws; ensure the shaft fully engages the coupler
• After reassembly, test with a cup of water to ensure smooth rotation

This high-voltage rectifier diode is used in the microwave's high-voltage circuit. It converts AC to DC so the magnetron can produce heat. A failed diode can cause no heat, loud humming, or a blown fuse when starting. What it does:

• Rectifies high-voltage AC to DC to power the magnetron
• Blocks reverse voltage in the HV circuit
• Common failure symptoms can include: runs but doesn't heat; loud hum then shutdown; line fuse blows at startup

• 1 high-voltage diode

• Unplug the microwave and properly discharge the high-voltage capacitor before servicing—dangerous voltage can remain even when unplugged
• Match diode orientation/polarity to the original and ensure a solid chassis ground connection where used
• Route leads and reinstall any clamps/insulators exactly as found; keep wiring clear of sharp edges and hot components
• If the original diode failed, inspect the HV capacitor and transformer for related issues before reassembly

The Door Handle Assembly is an OEM replacement part for GE microwaves. It is located on the outside of the door to provide a convenient and safe grip for users to open and close the microwave door securely.

Symptoms of a faulty door handle assembly include:

• Difficulty in opening or closing the microwave door
• Loose or wobbly handle
• Visible cracks or fractures on the handle

A bad door handle assembly can occur due to accidental damage, wear and tear, or broken components. If you encounter difficulties in opening or closing the microwave door, or notice any cracks or fractures on the handle, it may be time to replace the old or damaged door handle assembly with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

The glass tray is an OEM part for GE wall oven microwaves. It provides an essential, rotating surface for even cooking distribution in the microwave. 

Causes of a bad turntable tray can include wear and tear of the plastic hub bearing that allows rotation. Grease buildup can also cause reduced motion over time.

Symptoms of a bad turntable tray include: 

• Tray no longer rotates smoothly during the cooking cycle
• Uneven or incomplete cooking due to lack of movement
• Trapped food or messes between the tray and cavity wall

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This is the clear glass lens that covers the cooktop light on select GE over-the-range units. It shields the bulb from grease and splatters while allowing bright, even illumination of the cooking surface below.

• Protects the cooktop light bulb from grease, moisture, and debris
• Restores proper lighting if the original lens is missing, cracked, or stained
• Helps maintain safe, even illumination of the range area
• Common symptoms: broken or missing lens, dim or uneven light due to a damaged cover

• Disconnect power to the appliance before servicing
• Allow bulbs and surrounding area to cool completely
• Handle glass carefully to avoid chipping; wear cut-resistant gloves
• Ensure the lens seats fully and any retaining tabs/screws are secured per the product's service instructions

This turntable roller ring supports the microwave's glass tray and lets it rotate smoothly for even heating. Replace a worn or warped guide to stop wobbling, scraping noises, or a tray that no longer turns consistently.

• Supports and guides the glass tray as the motor and coupler rotate
• Keeps the tray level for smooth, low-friction turning
• Worn ring may cause the turntable not to rotate or to turn intermittently
• Other signs include tray wobble, squeaking/grinding sounds, and uneven heating

• Disconnect power to the microwave
• Remove the glass tray; lift out the old ring and clean the track
• Set the new ring in place with rollers facing down and centered on the track
• Reinstall the tray on the coupler, restore power, and test rotation

This hardware assembly secures designated components in your appliance, restoring a tight, rattle-free fit after service or wear. Replacing damaged or missing fasteners helps keep panels and parts aligned and operating as designed.

• Provides the correct fasteners/spacers for the specified location on the unit
• Replaces stripped, lost, or corroded hardware
• Helps eliminate looseness, vibration, or rattling noises
• Supports proper alignment and fit of the associated part or panel

• Disconnect power before servicing; allow hot surfaces to cool
• Support the part being fastened to prevent damage or misalignment
• Match each fastener one-for-one; note orientation and any washers/spacers
• Hand-start threads and do not overtighten; verify clearances and operation after install

The Fuse is an OEM part for GE microwaves. It serves as a safety device that protects the microwave by breaking the circuit if there is a power surge or electrical fault. This helps prevent damage to the microwave's components and ensures safe operation.

You should replace the fuse if it becomes blown or damaged. Causes of a bad fuse can include power surges, electrical faults, or issues within the microwave such as overheating. These factors can cause the fuse to blow, rendering the microwave inoperable.

Symptoms of a bad fuse include:

• The microwave not turning on or suddenly losing power
• No response from the microwave’s control panel
• The microwave stopping mid-cycle without completing the cooking process

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This flat bolt is a factory fastener used to secure appliance components. Replace a missing, stripped, or corroded bolt to restore a tight, secure assembly and help prevent loosening, rattling, or misalignment during normal operation.

• Fastens panels, brackets, and other components as designed by the manufacturer
• Restores a secure fit when the original hardware is missing or damaged
• Helps reduce looseness and vibration-related noises
• Built to original specifications for proper fit and function

• Disconnect power and allow the unit to cool before servicing
• Support the part being fastened; align holes before inserting the bolt
• Start threads by hand to avoid cross-threading; tighten securely without overtightening
• Reuse any original washers or spacers if present