Fase18c2abjw Parts

Color: white. It measures about 13 inches wide by 11-1/2 inches high.

This replacement air duct channels circulation air through the appliance, guiding it between sections to help maintain more even temperatures. A cracked, warped, or missing duct can leak air and reduce overall cooling performance. What it does:

• Routes air from the evaporator/fan to the outlet vents
• Helps balance airflow and temperature between compartments
• Gaps or misalignment can cause weak airflow or warm spots
• Cracks may lead to frost or condensation around the vent area
• Broken tabs or wear can create rattles or looseness

• 1 air duct

• Disconnect power before servicing; wear cut-resistant gloves.
• Remove shelves/covers to access the duct; note screw locations and any nearby sensors or damper components.
• Transfer any reusable foam seals/insulation from the original part and reinstall using existing hardware.
• After reassembly, ensure vents are clear and the fan operates smoothly.

The Door Hinge is an OEM part for Frigidaire dryers. This hinge allows it to open and close properly while maintaining a secure seal during the drying cycle.

Causes of a bad door hinge can include wear and tear from regular use, rust or corrosion due to exposure to moisture, or damage from accidental impacts. 

Symptoms of a bad door hinge include:

• Difficulty opening or closing the dryer door
• The door not sealing properly, leading to heat loss
• Squeaking or creaking noises when moving the door
• Visible damage or rust on the hinge

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This door switch senses whether the appliance door is closed and signals the controls to run only when it's safe. Replacing a worn or intermittent switch restores dependable starts and proper shutoff when the door opens. What it does:

• Detects door position and allows operation only when the door is fully closed
• Interrupts operation when the door opens for safety
• Common symptoms include: won't start, stops when the door is moved, or "door open" message/error
• Intermittent starts due to worn actuator or internal switch contacts

• 1 door switch

• Disconnect power before servicing
• Access the switch from the front or top panel; release mounting screws or tabs
• Move wires to the new switch one at a time to maintain correct positions, then secure the switch
• Test operation before reassembly

The Adjustable Foot is an OEM part for Frigidaire dryers. This part is located at the bottom of the dryer and allows you to level it, ensuring stability and proper operation. 

Causes of a bad adjustable foot can include regular wear and tear, damage from moving the appliance, or breaking due to excessive weight or stress.  

Symptoms of a bad adjustable foot include:

• The dryer wobbling or tilting
• Difficulty in adjusting the height of the foot
• Visible damage or deformation of the foot
• Unusual noises or vibrations during operation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This idler spring attaches to the idler arm to keep the drive belt properly tensioned, preventing slip and chatter. Replacing a weak or broken spring restores steady rotation and helps reduce noise and belt wear.

• Maintains correct belt tension by pulling the idler arm into position
• Helps prevent belt slippage, squealing/chirping, and premature belt wear
• A failed spring can cause no or intermittent rotation and the belt coming off
• Typical signs include a loose belt, off-track belt, or rhythmic squeak from the base

• Disconnect power before servicing; if working on a gas appliance, shut off the gas supply
• Access the idler assembly; note belt routing before removal
• Relieve belt tension, then move the idler arm to remove and replace the spring on the same mounting holes
• After reassembly, rotate by hand to verify smooth belt tracking before test

This replacement gasket restores a tight, reliable seal between mating parts in your appliance. It helps contain water or air at the joint to prevent leaks, odors, and performance issues.

• Creates a compressible barrier that prevents leaks at the sealed interface
• Helps maintain proper containment/airflow, depending on application
• Replace if torn, cracked, shrunken, or permanently flattened
• Typical symptoms include moisture or drips at the seam, musty odors, or visible damage

• Disconnect power; shut off water supply if applicable before servicing
• Use your model's parts diagram to locate and orient
• Clean and dry mating surfaces; remove any old adhesive or residue so the new seal seats properly
• Reassemble evenly, avoid over-tightening fasteners, and test for leaks after reassembly

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

The Motor Mounting Clamp is an OEM part for Frigidaire dryers. This clamp secures the motor in place within the dryer, ensuring it operates smoothly and remains stable during the drying cycles. The motor mounting clamp is essential for maintaining the proper alignment and function of the dryer motor.

Over time, the motor mounting clamp can become worn out or damaged due to constant vibration and movement. Accidental impacts or mishandling during maintenance can also cause the clamp to fail, leading to motor misalignment or instability.

Symptoms of a bad motor mounting clamp include:

• Excessive noise or vibration during the drying cycle
• Motor shifting or moving within the dryer
• Reduced drying efficiency
• The dryer not starting or stopping abruptly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This moisture sensor monitors dampness inside the dryer drum and signals the control when fabrics are dry, helping automatic cycles end on time and avoid overdrying. Replacing a failed sensor can restore consistent Auto Dry performance and cycle times. What it does:

• Detects moisture level via conductivity across the sensor surfaces inside the drum
• Sends feedback to the control so Auto Dry cycles advance and stop correctly
• Helps prevent overdrying and underdrying in sensor-based cycles
• Common symptoms of a faulty sensor may include: auto cycles ending too soon or running too long, clothes remaining damp, or the dryer staying on "Sensing" while timed cycles still work

• 1 moisture sensor

• Disconnect power and, if applicable, shut off gas before servicing
• Access the sensor at the front bulkhead/lint housing area; remove front panel as needed per model
• Transfer connectors and route wiring exactly as original; secure the sensor firmly
• Clean the sensor contact surfaces with rubbing alcohol; residue from dryer sheets or fabric softeners can affect readings

The Support Roller Washer is an OEM part for Frigidaire dryers, designed to ensure the smooth and stable operation of the dryer drum. Positioned between the support roller and the shaft, this washer plays a critical role in reducing friction and wear, allowing the drum to rotate smoothly and quietly.

Causes of these symptoms often stem from normal wear and tear, which can lead to the degradation of the washer over time.  

Symptoms of a bad Dryer Support Roller Washer include:

• Unusual noises, such as squeaking or grinding, indicating increased friction during drum rotation
• The dryer drum appears to wobble or is misaligned during operation
• Increased vibration of the dryer, which can lead to wear on other components

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This door switch detects whether the appliance door is open or closed. A working switch lets the machine start when the door is fully shut and stops operation when the door opens for safety.

• Monitors door position and allows the cycle to run only when closed
• Interrupts power to stop operation when the door opens
• Common symptoms of a failing switch: appliance won't start with the door closed, must press/hold the door to run, interior light stuck on/off, or a "door open" message on models with a display

• Disconnect power to the appliance before servicing
• Access the switch at the door opening/front panel; release mounting screws or locking tabs and remove the switch
• Move wires to the new switch one at a time to maintain correct positions
• After reassembly, test switch operation before running a cycle

This factory fastener secures appliance components and cabinet panels. Replacing a stripped, rusted, or missing screw restores a tight fit, reduces rattles and vibration, and keeps parts aligned for reliable operation. What it does:

• Fastens brackets, panels, and internal components to the cabinet/frame
• Helps maintain alignment and stability under vibration
• Direct replacement when the original is lost, corroded, or threads are damaged
• Common symptoms: loose or rattling panels, gaps/misalignment, or visibly missing hardware

• 1 screw

• Disconnect power; shut off gas/water if applicable before servicing
• Support the panel or component while removing/starting screws
• Match location and length to the original; start threads by hand to avoid cross-threading
• Tighten snugly—do not overtighten to prevent stripping

This small spacer fits on the idler assembly shaft to properly space and align the belt tensioner. Replacing a worn spacer helps keep the drive belt tracking correctly so the drum/tub runs smoothly and quietly. What it does:

• Spaces and centers the idler pulley on its shaft
• Helps maintain proper belt alignment and tension
• Can reduce squeaking or chirping from the idler area
• A worn or missing spacer may let the belt ride off, fray, or stop the drum/tub

• 1 idler spacer

• Disconnect power before servicing; let hot components cool
• Access the idler assembly per your model, relieve belt tension, and remove retaining hardware to slide off the pulley and old spacer
• Install the new spacer in the same location/orientation; reassemble and route the belt correctly
• Rotate the drum/tub by hand to verify smooth belt tracking before restoring power

This electronic control board manages your dishwasher's cycles and powers key components. Replacing a failed board can restore proper operation when the unit won't start, is unresponsive, or won't advance through a cycle.

• Directs fill, wash, drain, and heat functions by supplying timed power to the inlet valve, circulation motor, drain pump, and heater
• Interprets inputs from sensors and the door switch to advance and complete cycles
• Common symptoms: won't start, unresponsive controls, stops mid-cycle, or cycles that won't advance
• Also shows error indications or random beeps, or fails to power components despite good wiring

• Disconnect power at the breaker before servicing; avoid moisture and live circuits
• Handle the board by its edges and use ESD protection
• Access location varies by model; transfer connectors one at a time to the matching terminals
• Ensure all connectors and mounting points are secure before restoring power and test a short cycle