Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix loud whirling noise during spin cycle with this washer spin bearing washer. Supports the belt pulley bearing for smooth rotation. Video available.
I replaced the spin bearing, tub seal, washer and drive belt since I had it all apart. The video was extremely helpful...I would have tore the whole thing apart trying to figure out how the agitator came off....but it was very simple. Read more
Washer won't fill with water or only fills with hot? The water inlet valve controls water flow into the tub. DIY repair takes about 30 minutes.
This is my third repair of this type. The first was a stand-alone washer and was very easy, because there was a plate on which the inlet valve assembly was mounted, and it was easily removed. This repair was on a Frigidaire stacked washer/dryer (laundry center). Stacked washer/dryers are typically purchased to save space and are often tucked into a closet. Be sure you can pull it out to access both front and rear. Remove drain hose from drain, detach water hoses, electricity and dryer vent... Read more
Dryer door won't stay closed? The door strike secures the door latch during operation. Quick DIY fix—installs from the front in minutes.
My dryer door would not stay shut because the door strike was stuck in the door catch. I was afraid that when I pulled the strike out, it would damage the catch, so I ordered the door strike and door catch. I got the damaged door strike out with needle nosed pliers in about 15 seconds. The door catch was in perfect condition so I didn't need to use the one I ordered. So then I proceeded to install the new door strike. That took me about 15 minutes because I did not have the manual strength to... Read more
Timer knob for laundry center dryers. Attaches to timer shaft to control cycle selection and drying time. Replace if cracked, broken, or missing.
The old knob was not repairable. I ordered a new knob for the washer dryer stack unit. The order came within two days of ordering and it was the correct part. I was pleased. Read more
Supports the drum bearing in your dryer, allowing smooth drum rotation. Replace if cracked, broken, or worn to restore proper drum support and operation.
I watched the helpful diy video. It gave me what the problem was and the confidence to do it. Took my dryer apart with the helpful hints in the video repair went smooth. Works like a dream and I saved money. Thank you appliance parts pros. Read more
Washer won't advance through cycles or stops mid-cycle? The timer controls wash, rinse, and spin sequences. DIY-friendly repair restores normal operation.
I replaced the timer Read more
Replacement drain hose directs used water from your washer to the household drain. Needed when original hose is cracked, split, or leaking.
Our washer is next door the bathroom. So when, during the rinse cycle, the hose split and we found the back of the house completely flooded I initially assumed the culprit was either the toilet or the sink or possibly an interdimentional portal into a demonic netherworld of vaguely chlorine scented water. I spent the next hour mopping it all up and checking and re-checking the pipes in the bathroom with no apparent leaks. The next load of laundry left more clues as this time the flood was from... Read more
Dryer drum bearing ball ensures smooth drum rotation. Replace if drum wobbles, squeaks, or won't turn. Confirm fit with your model number before ordering.
Rotary control knob for laundry center washer and dryer settings. Replace if knob is cracked, broken, or missing. Fits control panel selector switches.
Pushed new knob on Read more
Replaces missing, stripped, or rusted 8-18 thread screws that secure dryer panels, brackets, and components for tight, rattle-free assembly.
It was easy to find the part on appliance parts pros. Once I found it I studied the diagram and determined that there were 3 screws in the drum that needed to be removed. I disconnected power and then removed 3 interior screws. Once I did that I removed the back cover and removed the single screw on the bottom side of the air duct that held it in place connected to the heat tube. I then reversed disassembly. I want to tell you this is a 2 person job. In order to assemble it you need to... Read more
Secures the blower wheel to the motor shaft in your dryer. Replace if worn, loose, or causing rattling noises to restore proper airflow. Verify fit by model.
The blower wheel center was worn down and spinning freely on shaft. Removing front covers, controls and brackets gave access to blower, which front half came off removing screws. (One screw underneath bracket) Pushed new blower on. (It's keyed and has small tabs that line up with groove on shaft). Installed clamp, reassembled and tested. Don't forget to pull the plug out before working on any appliance. Read more
Adjustable leveling leg that screws into the washer cabinet to stabilize and level your appliance. Replace if broken, damaged, or missing to prevent rocking.
After watching YouTube videos on possible cause, went to appliancepartspros and order seal and leveling legs since the had been missing since machne was given to us. Parts came in within the week and replaced . No more leaks!! Read more
Washer motor won't start or stops mid-cycle? This motor start capacitor stores electrical energy to start your washer motor. Moderate DIY repair.
I found your site which was most helpful. I saw on your forum, that others had replaced a motor & capacitor with + results. I was willing to spend what I thought was a reasonable amount & your guarantee was the clincher. I knew that if I called the appliance store where we had purchased the washer in 1998, it would be very expensive & even more important, it would take many days as they would have to order the part & then schedule a service call. I installed the motor & capacitor & was... Read more
Secures the drum baffle (lifter vane) to your washer drum. Replace missing, stripped, or loose screws to keep baffles firmly attached and prevent rattling.
Unscrewed the front lower panel ( 2 screws ). Disconnected the pump hose clamp and removed the hose. I loosened the lower back panel and pulled out the drained hose from the rear. Replaced with new hose put back clamp and panels. Very easy Read more
This gasket is a sealing component used in select appliances. It fits between two mating parts to keep water or air where it belongs, helping prevent leaks and ensuring proper performance. What it does:
This was more maintenance than a fix. I replaced the door gasket and temp sensor on my dryer. Thought what the heck and it might work more efficiently. I also replaced the shocks on my front loading washer. That was a bit of a chore, but could not have done it without the video that showed how to replace them. The socket was the life saver. All is working just fine. Who knows maybe I'll get another 20 year out of them. Read more
Fix a dryer that won't turn off or advance through cycles with a new timer. Controls cycle duration and automatic shutoff. Moderate DIY repair.
I ordered a new dryer timer. Read more