Glc2940fs1 Parts

Restore proper draining with this dishwasher drain pump assembly. It evacuates wastewater at the end of each wash and rinse, helping the tub empty fully so cycles finish correctly and standing water and drain errors are avoided. What it does:

• Drives an impeller to push water from the tub through the drain hose to household plumbing
• Activates during drain segments to clear the tub between and after cycles
• Helps resolve symptoms like water left in the bottom, slow or intermittent draining
• Addresses loud humming or grinding from the pump area and drain-related cycle interruptions

• 1 drain pump assembly

• Disconnect power at the breaker and turn off water before servicing
• Access from the lower front or bottom; place a towel or pan to catch residual water
• Label and unplug the wire connector, release the clamp/retainer, and remove the pump; transfer any model-specific seal or bracket if present
• Seat and align the new pump fully to avoid leaks, reconnect hoses/wires, then test for proper draining

The Cap-Burner is an OEM replacement part for Frigidaire cooktops and ranges. It is a crucial component that covers and protects the gas burner assembly, while also distributing the flame evenly for optimal cooking performance.

Symptoms of a bad Cap-Burner:

• Uneven or irregular flame patterns 
• Difficulty in igniting or maintaining a steady flame
• Discoloration or warping of the cap due to excessive heat exposure
• Clogged or obstructed gas flow, leading to poor burner performance

Causes of a defective Cap-Burner can include prolonged exposure to high temperatures, impact damage, or general wear and tear over time.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore cooktops and ranges.

Specs: B-16 HXW 1/2 SS

This replacement fan blade mounts to the appliance's fan motor to move air as designed. Installing a new blade restores proper airflow and helps reduce vibration or noise caused by bent, cracked, or worn fins. What it does

• Attaches to the fan motor shaft to move air through the cavity or across internal components
• Supports even air circulation or cooling performance, depending on model
• Helps resolve issues such as loud scraping/whirring, vibration/wobble, weak airflow, or visible blade damage

• One fan blade

• Disconnect power at the breaker and allow the appliance to cool completely before servicing
• Access the fan assembly from the rear panel or inside the oven behind the fan cover (varies by model); wear gloves—edges can be sharp
• Note blade orientation/rotation and securely reinstall using the original fastener(s)
• Hand-spin the blade to ensure clearance and free movement before reassembly and testing

The Main Control Board Kit is an OEM part for GE dishwashers. This electronic control board manages various dishwasher functions, including water intake, temperature settings, wash cycles, and drying times. It's the brain behind the efficient operation of your dishwasher, ensuring that all components work in harmony for optimal cleaning results.

The primary causes of control board failure often involve power surges, moisture damage, or component wear and tear, which can disrupt the electrical pathways and circuits within the board.  

Symptoms of a bad Main Control Board include:

• Dishwasher failing to start or stopping mid-cycle
• Unusual error codes displayed on the dishwasher panel
• Non-responsive controls or settings that don’t change appropriately

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This adhesive control panel overlay is the faceplate for the electronic oven control on select ranges and wall ovens. It restores readable button labels and a clean, protected surface when the original overlay is faded, bubbled, or damaged.

• Provides printed legends for the keypad buttons and display around the electronic control (EOC)
• Protects the touch surface from wear and cleaning
• Restores a neat, easy-to-read control area
• Typical replacement reasons: peeling, bubbling, cracks, discoloration, or illegible labels

• Disconnect power to the appliance before servicing the control panel
• Remove the control panel/bezel as required to access the old overlay
• Peel off the old overlay; clean and dry the mounting surface before applying the new one
• Align with display and key locations; press from center outward to bond and smooth out air

This replacement part is an upper rack slide, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. This upper rack slide is an important part of many appliances. This particular one is typically found in dishwashers and helps guide the upper rack in and out. This allows the user to have easy access to the rack in order to place and remove dishes before and after the cleaning process. A new upper slide rack might be needed if the current ones are broken or damaged in any way. It is possible that these slides become stripped over many years of use and need to be replaced. If the upper rack is tilted or not sturdy while being slid back inside the main tub, the upper rack slide might be the problem. Be sure the dishwasher is completely empty prior to replacing this part. This is a genuine OEM part and is sourced directly from the manufacturer. This upper arm rack slide is sold individually.

This middle spray arm hub secures the dishwasher's middle spray arm to the feed tube and lets it spin smoothly, helping deliver even spray coverage so dishes in the upper rack area get properly cleaned.

• Connects the middle spray arm to the water feed/manifold and serves as its rotating center
• Keeps the arm aligned so jets can distribute water evenly
• Wear or cracks can cause the arm to wobble, fall off, bind, or stop spinning
• Symptoms include poor cleaning on the upper rack and unusual noise from the arm area

• Disconnect power and water supply before servicing
• Remove the middle spray arm per your model's design and note its orientation
• Transfer and reuse any original screws, clips, or washers; install the new hub without overtightening
• Spin the arm by hand to ensure free movement before running a brief test cycle

This replacement thermostat is a temperature-sensitive switch used in select cooking appliances. It opens or closes at a fixed setpoint to control or limit heat, helping protect components and restore dependable operation of the affected circuit. What it does:

• Senses temperature at its mounting point and opens/closes electrical contacts at a designed setpoint
• Controls power to a heating or related circuit (such as an element or fan) to maintain safe operation
• Helps prevent overheating and protects internal components
• Failure can cause no heat, heat that shuts off prematurely, or a related circuit that won't turn on/off

• 1 thermostat

• Disconnect power to the appliance before servicing
• Access location varies by model; refer to your service manual for exact placement
• Move wires one at a time from the old part to the new to maintain correct connections
• Reinstall in the same orientation; ensure firm mounting for proper temperature sensing and secure electrical connections

This middle spray arm hub mounts the mid-level spray arm to its supply tube so it can spin freely and distribute wash water to the upper rack. Replacing a worn hub restores cleaning and keeps the arm secure.

• Attaches and centers the mid-level spray arm on its mount
• Provides a smooth bearing surface for proper arm rotation
• Helps deliver even spray coverage to the upper rack
• Common symptoms: poor cleaning on upper rack, middle arm not spinning, arm wobbling or falling off, unusual rattling from the arm area

• Disconnect power and shut off water before servicing
• Remove the middle spray arm assembly to access the hub
• Release the existing retainer/clip as designed, swap in the new hub, and reattach the spray arm
• The arm spins freely by hand, then run a short test cycle

The Rocker Switch is an OEM part for Frigidaire ranges and ovens. It is responsible for turning the interior oven light on and off. The light switch allows visibility of the oven cavity for viewing food during the cooking process.

Causes can include normal wear and tear over time, exposure to heat inside the oven cavity, or accidental damage.

Symptoms of a bad oven light rocker switch include:

• The oven light failing to illuminate when the door is opened
• The light remaining on even when the door is closed
• An inconsistent or flickering oven light
• The switch itself becoming loose, cracked, or non-responsive

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Color: White.

Has three terminals.

Size: 3/4 inch od x 1/4 inch id.

The Convection Fan Motor Kit is an OEM replacement part for Frigidaire ovens. This kit includes the motor responsible for driving the convection fan, which circulates hot air within the oven cavity to ensure even cooking and consistent temperatures during convection baking or roasting.

Over time, causes of a bad convection fan motor can include electrical wear, overheating due to heavy use, or damage from grease or debris buildup. Additionally, worn-out bearings in the motor can impair its performance.

Symptoms of a bad convection fan motor include:

• The fan not spinning or operating inconsistently  
• Uneven cooking results in convection mode  
• Strange noises such as rattling or grinding during operation  

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Note: Convection fan motor 5304467898 replaces earlier fan motors with a cooling blade. The fan motor doesn't include the cooling blade as it is no longer required.

Lower dishwasher rack roller axle only. Color: White. Measures about 1 inch wide by 1 inch high by a 1/2 inch deep. For Gray color order part number WD35X21041.