Gsd1222vbb Parts

• Will not fill with water

I took the inlet valve apart, found it was clogged with sediment, so I cleaned it and reinstalled it. Water was still not filing, so I figured the valve was sticking. I ordered a new valve,because $30 was a lot cheaper than a new dishwasher. I took out the old valve with two screws, and disconnected the supply line, the brass elbow, one hose, and a wiring harness. I reattached it in the same place, re-using the all the other parts, and once I turned the power and water back on, it worked as... Read more

First replaced the latch, spring, and lever, but no improvement. Then I saw the lever arm on the other half of the door, which by position had to be the way that the timer interacts with the soap dispenser. After turning off the power to the dishwasher, I removed the switch cover (not obvious how -- a video would help: on the left, I slid the narrow rectangular plastic wire cover a little to one side and gently opened it on its little hinge, which is near the left side of the door, and then... Read more

I found my parts and ordered the six I needed, however I did not pick up on the difference from the front wheels to the rear wheels in the the descriptions. The rear wheels are narrower and I ordered all front wheels, six fronts instead of four front and two rear. I made it work by using the axle from the new wheel with two old narrow wheels. Read more

First replaced the latch, spring, and lever, but no improvement. Then I saw the lever arm on the other half of the door, which by position had to be the way that the timer interacts with the soap dispenser. After turning off the power to the dishwasher, I removed the switch cover (not obvious how -- a video would help: on the left, I slid the narrow rectangular plastic wire cover a little to one side and gently opened it on its little hinge, which is near the left side of the door, and then... Read more

Found the correct racks on Appliance Parts.com. They shipped as promised. When I received them, however, I couldn't figure out how to replace the top rack. Didn't know how to get the end cap off Sooo - I went back on the website and watched the repair video and voila - was easy. All that was required was a flathead screwdriver and the knowledge of where to use it!!! Replacements in the dishwasher in 5 minutes or less. Great website and very helpful videos. I will recommend this website to... Read more

• Will not dispense detergent

1. Replaced the Dishwasher motor and pump assembly. 2. Replaced the lower arm sprayer. 3. Replaced the Sump and filter. Replaced both the inlet and outlet hoses. 4. Replaced the Airgap. 5. Replaced Float Dome. 6. Replaced Water Inlet Valve. Parts $220 for Dishwasher Estimated Labor $400.00 Labor $0.00 Parts $100.00 for Pullout Faucet Estimated Labor $175.00 Labor $0.00 Read more

Although I ordered the latch, lever and a new cup and replace the original pieces the dispenser still did not close. On further inspection it turned out to be a small spring that had fallen out of place. Once the spring was reconnected the dispensing cover worked fine. I'm still happy that I replaced the entire assembly with new parts regardless. Discovering the loose spring took the most time. Read more

First replaced the latch, spring, and lever, but no improvement. Then I saw the lever arm on the other half of the door, which by position had to be the way that the timer interacts with the soap dispenser. After turning off the power to the dishwasher, I removed the switch cover (not obvious how -- a video would help: on the left, I slid the narrow rectangular plastic wire cover a little to one side and gently opened it on its little hinge, which is near the left side of the door, and then... Read more

Replaced with a new Inlet Sump [WD18X213]. It was a little tedious, attaching the Inlet Sump, back to the pump, because I did the job with the dishwasher in place (not pulled out). My dishwasher was plumbed with copper pipe, so I really didn't want to upset that. Also, I had previously replaced the motor and the pump in this dishwasher, so I was familiar with how the Inlet Sump attached to the pump. Again, it's very tight working under the unit while it is still in place, and I wouldn't... Read more

• Door latch failure

First replaced the latch, spring, and lever, but no improvement. Then I saw the lever arm on the other half of the door, which by position had to be the way that the timer interacts with the soap dispenser. After turning off the power to the dishwasher, I removed the switch cover (not obvious how -- a video would help: on the left, I slid the narrow rectangular plastic wire cover a little to one side and gently opened it on its little hinge, which is near the left side of the door, and then... Read more

The replacement arm arrived promptly. Removing the old spray arm hub was very difficult by hand, plumbers wrench, or adjustable wrench. However, by inserting a screwdriver trough the two opposite holes where the tabs had broken off, it is relatively easy to unscrew the old hub. Read more

Myself removed old part replaced with new Read more

In the How to fix it your self section of Questions and Answers, your answers for removing the Base Spray Arm is incorrect. It states "just stick a screw driver into the base spray arm from inside the tub and turn", that does not work. Their are 2 tabs that in gauge the base spray arm with the tub. A 4 prong round wrench is required to insert from the bottom into the pump connector and turn the nut that sits inside. Read more

Replaced heating element. Read more

• Leaking

I replaced the pump drain assembly. The flapper valve was included in the assembly, so I did not need to order that. On previous repairs, the old drain hose was tricky to reinstall, so I replaced it and the hose clamp.The silverware basket had holes in the bottom and required replacement. I had some broken tine clips. Read more

• Will not fill with water

Took the washer out, turned it over and found the solenoid that worked the drain valve to be melted, and the shaft that the solenoid activates was heavily corroded. I found the right parts on your website after reading the notes left by other customers, then watched the video. The repairs were fairly simple and successful. This was a GE profile dishwasher. Read more