Gss25sgmd Bs Parts

The new slides fit perfectly. One thing to mention is that the slide rails come with the slide bearings so you do not need to buy those separate. When I called I was told I needed the bearings so I bought 3 assuming I would be able to salvage the others. Turns out I did not need them. Read more

Condenser fan stopped on my big 2003 Monogram 4 foot wide ZIS480D Refrigerator. It is top mounted. The fridge had to be rolled out. 20 screws removed and the top sheet metal to get at the condenser. That was the only way to get at it. Works like new now. Read more

The new slides fit perfectly. One thing to mention is that the slide rails come with the slide bearings so you do not need to buy those separate. When I called I was told I needed the bearings so I bought 3 assuming I would be able to salvage the others. Turns out I did not need them. Read more

Changed fan motor, rubber grommets, and dust cover. It sounded like the vibrating sound was being caused by the motor. But, come to find out I had a chipped blade on one of the fan blades. So make sure and check the fan blade first. Thanks Appliance Parts Pros everything for just as it should. Read more

This was a two and half year issue as different things failed at different times. I would get one part, then another would fail. Ultimately, I got to a point where what failed, I hadn't been ordered the part yet. The seal on the freezer door took three bathing's before it plumped up and un-creased. The directions on the box it is shipped in said to heat the seal up in hot water then cool it down with tap water. I didn't need to do that. It took a lot of massaging of the seal, but... Read more

I looked for a site that sold replacement parts for my make of GE refrigerator. I found AppliancePartsPros, and was very surprised at how organized it was. By entering the model number of my refrigerator, I was shown a set of (approximately) 8 general parts diagrams for my refrigerator. I chose the ice making/dispensing diagram. I matched the part that shattered (from use) to what was on the diagram. What I didn't know was how to install the part. I saw references by other customer comments to... Read more

Pop out the old switches with a putty knife pressing down on the tab, grabbed with pliers to pull out, disconnect the wires and connect new switches, pressing back in place. Read more

I changed the motherboard - computer and also changed the motor in the freezer, because it was doing a howling sound every time it turned on. The repair technician asked for $500 for a repair and that is on top of the $230 I paid him two days before. I looked up the parts and decided to try myself and it paid off. Great instructional videos. Thanks Read more

Ordered new parts Read more

I replaced the supply line to the fridge - no change in taste. I replaced the MWF manifold and tubes, the water inlet valve and the water storage line. That did it, good tasting water again! The ice still has a bad taste, so I'll replace the supply tube from the valve to the ice maker. Overall, replacing these parts was easy and the videos from Appliance Parts Pros helped. Read more

The front wheel assembly replacement (WRXO2X12454) was straightforward and easy to do. Took maybe 30 minutes start to finish. The rear wheel assembly (wheel WRO2X10695 and axle WRO1X10604) that was more involved as the original wheel axle is actually a rivet that you have to cut out. 1. I used a vibrating multitool with a carbide blade to cut the axle out. Had to use a pair of vise grips to hold the rivet to keep it from spinning while cutting it. 2. The new axle I drilled a 2mm hole thru the... Read more

This was a two and half year issue as different things failed at different times. I would get one part, then another would fail. Ultimately, I got to a point where what failed, I hadn't been ordered the part yet. The seal on the freezer door took three bathing's before it plumped up and un-creased. The directions on the box it is shipped in said to heat the seal up in hot water then cool it down with tap water. I didn't need to do that. It took a lot of massaging of the seal, but... Read more

Ordered new parts Read more

Replaced the stripper and fill cup - turns out that the fill cup came with the locking tab broken off. The stripper had a missing paddle, and ice cubes would jam and shut down the ice maker periodically. Let the ice maker warm up after you remove it so the plastic is not so brittle. You have to pry the old stripper out. Make sure the new one locks all across the front. My refrigerator has the ice maker mount toe the side instead of from the hangers in back. I wasn't sure how to remove it,... Read more

New cond fan & new evap fan & new defrost heater unit Read more

Ordered new parts Read more