Gu2275xtv Parts

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

This is the front console/control panel assembly for select laundry units. It provides the user-facing buttons and display area that houses and protects the controls, restoring a clean look and proper access to cycle selections.

• Houses the user interface and control selector areas on the appliance front
• Replaces a cracked, loose, or discolored console panel
• Helps resolve issues like broken mounting tabs, missing buttons, or difficulty operating controls
• Cosmetic damage or wear to the control area

• Disconnect power before servicing to avoid electrical shock
• Use care to transfer any existing electronics, knobs, or overlays if required by your model
• Keep track of screws and clips; support the panel to prevent cracking during removal/installation
• Verify proper alignment of harness openings and mounting points before tightening fasteners

This small clip secures the guard/shield on the dispenser assembly. Replacing a cracked or missing clip keeps the guard firmly attached and aligned so the dispenser operates properly without interference, noise, or premature product loss. What it does:

• Fastens the dispenser guard to its mounting point on the dispenser assembly
• Keeps the guard aligned to prevent interference with dispenser door/flow
• Restores a secure fit if the original clip is cracked, deformed, or missing
• Common symptoms: loose or missing guard, rattling, incomplete dispensing or residue left after a cycle

• 1 dispenser guard clip

• Disconnect power to the appliance; turn off water supply if applicable
• Open access, support the guard, and release the worn clip from its tabs
• Snap the new clip fully into place, ensuring it engages all locking points
• Ensure the guard is secure and that the dispenser door/flow path is unobstructed before use

Color: White. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For grey use WP676455. For tips use 675679

Overfill control.

Replacement door latch assembly for dishwashers. It locks the door and signals the control when closed so cycles can start and run without interruption. A worn latch can cause no-start conditions or intermittent stopping. What it does:

• Secures the door by engaging the tub strike during operation
• Provides a door-closed signal to the control via internal switch(es)
• Helps prevent operation with the door open for safety
• Common symptoms: cycle won't start, door won't latch or pops open, cycle stops when the door is jostled, Start light blinks

• Includes: 1 door latch assembly

• Disconnect power to the dishwasher before servicing
• Access the latch by removing the inner door panel/console; note wire locations before disconnecting
• Reuse any mounting hardware from the original latch if needed; mount and align so it engages the strike cleanly
• Reassemble and test that the door latches and a cycle starts

This inlet protector is the coarse screen that covers the dishwasher's pump/sump inlet, blocking large debris from entering the wash system. Replacing a damaged or missing protector helps maintain water flow and protect the pump from jams or wear.

• Screens large food particles and debris from the pump/chopper inlet
• Helps maintain proper water circulation and consistent cleaning performance
• Reduces risk of pump damage or noisy operation from debris
• Common signs: cracked or missing screen, persistent debris in the sump, grinding/rumbling noises, or declining wash results

• Disconnect power and shut off water supply before servicing
• Remove the lower rack and spray arm; access the sump/accumulator area per your model
• Lift out the old protector; seat the new protector fully and secure any tabs/fasteners
• Reassemble and ensure the screen sits flat with no gaps

Seal included. This sump housing assembly includes a 32.17 millimeter hole for the thermistor. If the hole for the thermistor is 31-31.5 millimeters you will need to order WP8534882.

This overfill float and shaft assembly monitors the dishwasher's water level. As the tub fills, the float rises and triggers the float switch to shut off the inlet water, helping prevent overfilling and leaks.

• Senses tub water level and moves up/down with the water
• Activates the float switch to stop filling at the correct level
• Helps protect against overfill-related leaks
• Common symptoms include: won't fill (float stuck up), continuous filling/overfilling (float stuck down or damaged), or float not moving freely

• Disconnect power and turn off the water supply before servicing
• Lift the old float straight up from inside the tub; access the underside (behind the toe panel) as needed to release the shaft from the float switch lever
• Install the new shaft through the guide and onto the switch lever; seat the float so it moves freely
• Verify smooth float movement and test a fill cycle while checking for leaks

This replacement part is a dishwasher pump and motor assembly. The dishwasher pump and pump motor circulate water through the dishwasher's spray arm. When the spray arms aren't spraying properly, this could mean that it's time for a new pump and motor assembly. Luckily replacing this part is a relatively simple process.Start by making sure the dishwasher is unplugged. After that shut off the water supply going to the dishwasher. Then disconnect the drain line from the garbage disposal or sink drain. Open the dishwasher door and pull out the bottom dish rack. Remove the upper dishrack from its track. Release the spray arm on the bottom of the washer. Then proceed to release the feed tube clips. Using a nut driver remove the bottom access panel and tow panel. Pull them out to remove them. Remove the power cable from the junction box, and disconnect the supply line from the inlet valve. Proceed to pull the dishwasher out of the counter. Tilt the dishwasher on its side and pull the hose from the drain pump. Remove the wire harness from the pump. Disconnect wires from diverter motor and circulation motor. Once complete, proceed to tilt the dishwasher upright and remove the pump and motor assembly from the bottom of the dishwasher. Replace with the new assembly.This replacement part is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand dishwashers.

This heater support holds the heating element securely in place inside the appliance, maintaining correct alignment and clearance for reliable operation. Replacing a worn or broken support helps prevent sagging, noise, or damage from an out-of-position element.

• Secures the heating element to its mounting point to keep it stable
• Maintains proper spacing from nearby components and surfaces
• Helps reduce vibration, rubbing, or rattling noises
• Replace if the original support is cracked, warped, missing, or the element appears misaligned

• Disconnect power to the appliance before servicing; allow hot components to cool
• Access the heater per your model's service information; note the original orientation and routing
• Seat the support fully and handle element leads carefully to avoid damage

This factory-spec screw secures panels and components in your appliance. Replacing a missing or stripped fastener restores a tight, rattle-free fit so parts stay aligned and operate as designed.

• Fastens brackets, panels, and internal components to their mounting points
• Maintains alignment and reduces vibration during operation
• Replaces missing, worn, rusted, or stripped hardware
• Helpful when you notice rattling, loose panels, gaps, or parts shifting out of position

• Disconnect power; shut off water or gas supply if applicable
• Align the part being secured and remove any damaged hardware
• Hand-start threads to avoid cross-threading; tighten with the correct driver
• Do not overtighten; verify the assembly is secure and operates freely

Color: gray. Measures about 3 inches wide by 1-1/2 inches high.

This replacement shield fits over the heater/probe area to provide a protective barrier. It helps prevent direct contact and excessive radiant heat exposure, protecting nearby components and supporting accurate temperature sensing for consistent operation. What it does:

• Shields the heating element and adjacent temperature probe/sensor area
• Helps prevent heat damage to nearby plastics, wiring, and components
• Reduces the chance of items contacting or striking the heater/probe
• Common signs it's needed: cracked, warped, or missing shield; discoloration; rattling or an exposed probe/heater area

• 1 shield

• Disconnect power and allow all heated parts to cool before servicing
• Access the heater/probe area and note the original shield orientation
• Seat the shield fully; secure with existing clips/fasteners if applicable
• Verify clearances around the heating element before restoring power

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

Bushing, Door spring