Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Usually ships within 4 - 14 days
The Torsion Spring is an OEM part for GE refrigerators. It is essential for maintaining the proper tension and operation of the refrigerator door. This spring ensures the door closes smoothly and stays securely shut, preventing cold air from escaping and maintaining the appliance’s efficiency.
Causes of a bad torsion spring can include metal fatigue from regular use, corrosion from exposure to moisture, or damage due to excessive force or mishandling. Over time, these factors can weaken the spring, affecting the door’s performance.
Symptoms of a bad Torsion Spring include:
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Replaced springs, flapper assembly and ice door retainer as described in videos and it was easy. So far so good..water dispenses. Read more
This ice bucket assembly is a genuine LG part, sold individually. This ice bucket assembly can be used as a replacement part in a refrigerator. This part stores and dispenses ice produced by the ice maker.This ice bucket assembly is a complete replacement for a damaged or broken ice bucket. Usually, if an ice bucket isn't dispensing ice properly, it's because of the augur. Symptoms of a defective augur can include an ice maker that will not dispense ice, that will not make ice, that uncontrollably dispenses ice, or that does not dispense as much ice as usual. If this is the case, the ice bucket should be removed and replaced with this genuine OEM replacement part before using the ice maker again.This is an OEM part sourced directly from the manufacturer. This ice bucket assembly is compatible with the following appliance brands: General Electric, RCA, and Hotpoint.
Pulled the old one out, slid the new one in. Read more
The Dispenser Drip Tray is an OEM part for GE refrigerators. It's placed beneath the water and ice dispenser to catch drips and spills, preventing water from running down the front of the refrigerator or onto the floor. This part not only helps in keeping the dispensing area clean but also minimizes the risk of slip hazards caused by wet floors.
Over time, the dispenser drip tray can become stained, cracked, or warped, affecting its appearance and functionality.
Symptoms of a bad Dispenser Drip Tray include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
Was an easy swap. Ordered the pieces, got them withing two days. Didn't realize a hair dryer would melt so much of the plastic pieces that I couldn't even see while trying to defrost the water line in the door. Next time it happens I will just empty the freezer and leave the door open for a few hours. Will save me from making this mistake again. Thankfully easy to replace the parts myself and not too expensive. Read more
The Front Roller Assembly is an OEM part for GE refrigerators. It's designed to support the front part of the refrigerator, allowing for smooth and easy movement when you need to shift the appliance for cleaning, maintenance, or repositioning. This roller assembly ensures the weight of the refrigerator is evenly distributed, reducing strain on the floor and making it easier to move the refrigerator without damaging the flooring or the appliance itself.
Causes of a bad Front Roller Assembly can include wear and tear from regular use, damage from moving the refrigerator improperly, or corrosion over time.
Symptoms of a bad Front Roller Assembly include:
Replacing the roller assembly corrected the problem. The key to replacing the roller assembly is elevating the refrigerator high enough to remove the roller assembly. (1) Raise and secure the refrigerator, (2) remove the metal bar across the bottom of the refrigerator to provide adequate access to the roller assembly (2-screws), (3) remove the roller assembly adjustment screw, (4) pry the roller pivot pin out, (5) pull the roller assembly toward the front of the refrigerator to remove, (6)... Read more
First I ordered a new ice door seal, spring, and crank, figuring the condensation in freezer and door was caused by ice door not sealing. Turns out the solenoid for the ice door was completely rusted and was the primary cause, if it had been replaced early, it would have saved the dispenser board. What then happened was the moisture in the freezer door damaged the control board rendering dispenser controls inoperative as well as the heater around the dispenser. Now the freezer door is dripping... Read more
I ordered the upper and lower cam riser, replaced them, and adjusted the door and the door works great. I've bought many parts in the last 10 years from AppliancePartsPros for this 20-year-old side-by-side refrig. Still works great. Thanks, ED Read more
The front wheel assembly replacement (WRXO2X12454) was straightforward and easy to do. Took maybe 30 minutes start to finish. The rear wheel assembly (wheel WRO2X10695 and axle WRO1X10604) that was more involved as the original wheel axle is actually a rivet that you have to cut out. 1. I used a vibrating multitool with a carbide blade to cut the axle out. Had to use a pair of vise grips to hold the rivet to keep it from spinning while cutting it. 2. The new axle I drilled a 2mm hole thru the... Read more
Replaced Ice maker very easy. Read more
Swapped it out for new tube. Take 5 minutes and zero effort. The drain tube will clog with mold. You can clean it out but the tube will clog again despite's you best efforts as the tube wall provide a great habitat. Ordered new tubes to facilitate swap-outs. Old tubes can be cleaned but will recolonize quickly. Read more
I ordered the heater unit from your website as well as a new evaporator panel gasket and thermostat. Once I removed the evaporator panel from the rear wall of the freezer side, I used a steamer machine I had to melt all the ice which had accumulated, I replaced the faulty heater unit and all is well. By-the-way, I consider your website amongst the very best and easy to use. I appreciate how well your developers and designers created the diagrams/pictures with numbered parts displayed,... Read more
Very easy to replace the trays slide the broken one out, slide the new one in, no problems. Read more
I had 2 parts that were cracked, so after changing the cracked parts as well as the dispenser switch, it was back to working normally. Simple to make the needed repairs and the videos provided on your website really helped in being prepared. Read more
I ordered the recommended front door shelf part Fz for my frig, it was shipped promptly. It was slightly too long, so I cut about a 1/4" with the saw... it fits nicely now. Read more