Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Touch-up paint for covering scratches, chips, and minor blemishes on appliance exteriors. Restores appearance and protects surfaces when finish is damaged.
Touch up paint Read more
Fridge not cooling but freezer works? Squeaking or chirping noise? A failed evaporator fan motor stops cold air circulation. DIY repair with video guide.
My KitchenAid refrigerator was not cooling, but the freezer was working perfectly. The help section here listed three parts that could be defective–defrost thermostat, evaporator fan motor and blade, and air diffuser/damper control–so I replaced them all. The videos were EXCELLENT, and despite the difficulty I had squeezing my shoulders into the small freezer compartment, I installed the parts and my refrigerator is cooling perfectly! THANK YOU FOR THE EXCELLENT REPAIR VIDEOS! I am so happy... Read more
Mounting screw for refrigerator ice maker assembly. Secures components to maintain structural integrity. Replace if lost, stripped, or corroded.
Took off the freezer door, took off the top hinge on the refrigerator door, replaced the handle, re-installed the top hinge and the freezer door. This is a two person job - one to remove the top hinge and replace the handle, while a second person holds the refrigerator door in place. Replacing the handle was easy. The most irritating part was figuring out what parts to order. The drawing of the refrigerator door (Drawing # 4) used to figure out what parts to order was not clear. I paid $8... Read more
Ice buildup in freezer or warm fridge? This defrost heater melts frost from evaporator coils during the defrost cycle. Moderate DIY repair with video guide.
Tried to put refrigerator in defrost mode and defrost would not initiate. Checked the bi-metal and heater, both tested good. Replaced the ADC board and refrigerator went in to defrost. problem solved. Read more
Seals refrigerator door to prevent warm air entry and maintain temperature. Replace if cracked, torn, or doors won't close tightly. Verify fit by model.
I took the new seal out of it's packaging and used a blowdryer on low heat to soften up the seal so that the crease from shipping (it was folded to ship) disappeared. Next I took the refrigerator door off, removed the old seal, & cleaned the area where the new seal would be applied. Following the video on the Appliance Pro Parts website, I re-installed the new seal and put the door back on. Last step was to snap on the new hinge cap I ordered. The video online was easy to follow and this... Read more
Creates an airtight seal around your freezer door to maintain consistent temperatures and prevent cold air loss. Replace if torn, cracked, or loose.
Replaced Case Water Filter assembly DA81-05883A. Please read my post entirely before starting. I completed all the tasks that I could without having to disconnect the refrigerator since it was full of food. First I removed the panel on top of the refrigerator that covers the water line that feeds the dispenser. Do not disconnect any electrical connections or the water line at this time. Remove the panel from the back bottom of the refrigerator that covers the compressor and water valve,... Read more
Protective cover for the ice maker's infrared emitter sensor in the freezer compartment. Replace if cracked, broken, or missing to shield the sensor.
Followed the video you provided. Read more
Replacement cap that seals the water filter housing and attaches to filter cartridges. Needed when cap is cracked, broken, or missing notches prevent secure fit.
Replaced filter cap with new one. The minor challenge was to find a method of pulling the filter out of refrigerator (which is normally done by pulling on the filler cap. The filter was recessed to far into the refrigerator for me to be able attach the new cap. I had to find another tactic to remove the filter. The solution was to look at the replacement filter to notice where two slots were located at the end of the filter. I then used a paint can opener (found at most paint stores) to slip... Read more
Water leaking from bottom of fridge? Cracked evaporator drip tray lets defrost water escape. Moderate DIY repair, about 45-60 minutes with our guide.
The drain pan (Tray-Evaporator Pan) was cracked in 2 places. We had to remove the front panel. Loosen the bracket that holds the water filter. Take off the back panel and disconnect the bracket that holds the selenoid. It was not necessary to unhook the water lines, just the bracket. It was not easy to remove the old pan and get the new one in, but holding the water filter, with the bracket intact, as far to the left side of the refrigerator as possible gave us the room to get the pan in. ... Read more
Secures the handle end cap to the center of your refrigerator door. Replace if missing, stripped, or lost during handle repairs. 8-18 x 1/2 inch size.
This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more
Stores and chills water before dispensing. Replace if cracked, leaking, or causing slime/film buildup in dispensed water. Installs inside refrigerator.
After watching installation videos on each felt I could pull it off and ordered and received replacement water reservoir and water dispenser tube assembly. Reservoir installation went off without a hitch outside of the added step of the need to remove the entire main in waterline assy in order to access the connectors which also were not as represented in video, in that they were not the press-to-release type but standard threaded compression types. Water Dispenser tube/spout assembly was much... Read more
Fix an ice maker that stopped working or leaks water into the bin. This ice mold tray replacement takes about 10-20 minutes with our step-by-step video.
I have a Whirlpool Side-by-side Model ED22PWXBW01. A year ago, the ice cubes started freezing together in the rear of the ice bin for no apparent reason. Although the problem started off small, it gradually grew much worse, and finally I could see water dripping out of the ice mold and into the bin during the fill cycle. Re-levelling the refrig didn’t help, nor did adjusting the cube size / fill level. With guidance from the video, I removed the icemaker from the wall of the freezer. The... Read more
Fix a loose or wobbly dispenser paddle with this strain relief. Cushions the dispenser arm connection to prevent wear. Easy 5-minute repair with video guide.
With the help of the fantastic videos provided on the web site for each replacement part, it was extremely easy to complete the repair Read more
Refrigerator warm but freezer cold? Noisy evaporator fan? This mounting grommet reduces vibration and noise. Takes about 1 hour to replace with video guide.
I could not be happier with my Appliance Parts Pros experience. I googled my symptoms, and the 2nd result was a video from Appliance Parts Pros describing what the problem might be and exactly how to fix it. There was such a close match between my symptoms and the description that I ordered the parts --- with a 365 day return policy, my risk was limited. Almost too good to be true, the parts arrived next business day! I took it slow (about an hour) to install the new evaporator fan motor,... Read more
Bottom mounting screw for refrigerator ice maker auger assembly. Secures auger blade components together. Replace if stripped, damaged, or missing.
Replaced the auger, blade and screw (bottom) Read more
Horizontal metal rod that secures glass shelf panels inside your refrigerator door. Replace if broken, bent, or missing to prevent shelf slippage.
Cut piece to fit Read more