La320t Washer Whirlpool Parts

This replacement hose carries liquid bleach from the dispenser into the washer tub. Restores proper dispensing and helps prevent leaks or splashes when the original hose becomes brittle, cracked, or loose.

• Routes bleach from the dispenser funnel to the outer tub during the cycle
• Helps keep bleach off the top panel, wiring, and cabinet surfaces
• Symptoms include leaks near the dispenser area, bleach left in the cup, or a strong bleach odor inside the cabinet
• Visible cracking, hardening, or splits on the hose are common failure signs

• Disconnect power and turn off water supply before servicing
• Access the dispenser area; place a towel to catch residual liquid
• Note hose routing and orientation; release clamps and transfer/reuse them as needed
• Fully seat the hose on both fittings, secure with clamps, and test for leaks after reassembly

Rubber grommet for motor mount stud.

10 - 16 x 1/2

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This thrust ring is a small spacer that controls end-play on a shaft or gear, keeping parts aligned and reducing friction. Replacing a worn ring restores smoother, quieter operation and helps prevent premature wear in the assembly.

• Maintains axial spacing and limits end-play in rotating assemblies
• Reduces friction and metal-to-metal contact between components
• Helps stabilize shafts/gears to minimize noise and vibration
• Replace if you notice scraping/grinding sounds, wobble, or visible wear on the old ring

• Disconnect power before servicing
• Refer to your model's parts diagram to confirm orientation and stack order with any spacers/washers
• Clean the shaft and mating surfaces; replace any companion parts that show severe wear
• After reassembly, check for smooth rotation and proper end-play before returning to service

This 1-1/8 in wire retaining ring locks into a groove to secure components in place. It helps prevent parts from sliding off a shaft or shifting out of position so assemblies stay aligned and operate reliably.

• Holds components on a shaft or within a groove to prevent axial movement
• Maintains alignment of related parts in the assembly
• Common failure signs: ring is bent, missing, or won't stay seated
• Symptoms include loose or wobbly parts and rattling during operation

• Disconnect power before servicing
• Wear eye protection—retaining rings can spring free during removal
• Use appropriate snap-ring pliers or small picks to remove/install
• Ensure the ring is fully seated in the groove before reassembly and use

This spring fastener applies constant tension to hold a component securely in place inside your appliance, helping prevent looseness, vibration, or gaps. Replacing a fatigued or missing clip restores a tight, reliable fit.

• Provides spring tension to clamp and retain a part, seal, or panel
• Helps maintain alignment and reduce vibration or rattling
• Restores secure attachment when the original clip is bent, stretched, or missing
• Symptoms can include a part not staying put, visible looseness, or a clip that's damaged or gone

• Disconnect power; turn off water supply if applicable
• Use needle-nose pliers or a suitable spring tool; wear gloves and eye protection
• Note the original orientation before removal to ensure proper reinstallation
• Make sure the mating part or seal is fully seated and the fastener is fully engaged before reassembly

This vacuum break is the washer's water-inlet anti-siphon fitting. It maintains a required air gap so the tub fills properly without drawing used water back into the supply, helping prevent leaks and backflow issues.

• Maintains an air gap at the inlet to prevent backflow/siphoning into household water lines
• Helps ensure consistent, unobstructed water flow into the tub
• Replaces a cracked, clogged, or leaking vacuum break at the fill area
• Common symptoms include leaks from the rear/top during fill, visible cracks, or restricted/noisy fill

• Unplug the appliance and shut off both water supplies before servicing
• Access the fill/inlet area; note hose routing and part orientation
• Remove hose clamps/hoses and the old vacuum break; install the new part and secure clamps
• Restore water and power, then run a fill test and check carefully for leaks

Specs: 10-16 x 1/2 inch.

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

This agitator assembly is the center post in a top-load washer. It transfers drive motion to move water and fabrics, restoring proper wash action when the original agitator is cracked, stripped, or loose.

• Oscillates in the wash basket to circulate clothes and water
• Engages the drive shaft/splines to create agitation
• Replaces a damaged or worn agitator to maintain wash performance
• Common symptoms: no or weak agitation, clothes not moving, visible cracks, wobble

• Disconnect power to the washer before servicing
• Remove the fabric softener dispenser and cap, then the center hold-down bolt
• Pull the old agitator straight up; align splines and seat the new agitator, then reinstall and tighten the bolt
• Reinstall cap/dispenser and run a short test cycle

The Leveling Leg Pad is an OEM replacement part for Whirlpool washing machines. This small but essential component fits beneath the leveling legs, providing stability and preventing the appliance from moving or vibrating excessively during operation. It also protects flooring surfaces from potential scratches or damage.

Symptoms of a bad Leveling Leg Pad include:

• Increased vibration or noise during the wash or spin cycle
• The washing machine wobbling or becoming unsteady
• Visible wear, cracks, or damage to the pad

Causes of a failing Leveling Leg Pad can include wear and tear from prolonged use, exposure to moisture, or excessive weight causing deformation. Replacing worn pads helps maintain the appliance's balance and efficiency.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

For the leveling leg order 22003428.

This adapter tube assembly connects sections of the appliance's water line to create a secure, leak-resistant path for water flow. Replace it if the tube is cracked or the connection no longer seals properly to prevent leaks and restore flow.

• Connects water tubing between components within the appliance's water system
• Helps maintain a tight, leak-resistant seal at the joint
• Restores proper water flow when a tube or connector is damaged
• Typical symptoms: water leaking at the connection, reduced or no water flow, visible cracks/kinks, loose fit

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure and place a towel or pan to catch any residual water
• Note routing and orientation before removal to ensure correct reassembly
• After installation, restore water and check all connections for leaks

Leg, adjustable (w/nut)

This is an inner tub basket intended for use with washing machines and combination washers and dryers. It is located inside the washing machine in the middle of the appliance. The inner tub basket is responsible for holding clothing during a washing cycle. It has an agitator in the middle and sides with holes so that water can leave when the tub is spinning. It is attached to the outer tub, which seals in the water.The inner tub basket can become damaged and cause loud noises, leak, or fail to drain. If this occurs, this component will need to be replaced. Basic tools will be needed for the process. Make sure the washing machine is unplugged for safety. The hoses will need to be removed before taking out the inner tub basket and replacing it with a new one. The inner tub basket is sold on an individual basis. It is an authentic OEM replacement part that is sourced directly from the manufacture. This part is compatible with washing machines and washer/dryer combination appliances made by Inglis, Estate, Admiral, Crosley, Roper, Magic Chef, Amana, KitchenAid, Maytag, Kenmore, and Whirlpool.