Mah55oobww Parts

The Leveling Leg Pad is an OEM replacement part for Whirlpool washing machines. This small but essential component fits beneath the leveling legs, providing stability and preventing the appliance from moving or vibrating excessively during operation. It also protects flooring surfaces from potential scratches or damage.

Symptoms of a bad Leveling Leg Pad include:

• Increased vibration or noise during the wash or spin cycle
• The washing machine wobbling or becoming unsteady
• Visible wear, cracks, or damage to the pad

Causes of a failing Leveling Leg Pad can include wear and tear from prolonged use, exposure to moisture, or excessive weight causing deformation. Replacing worn pads helps maintain the appliance's balance and efficiency.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

For the leveling leg order 22003428.

Color: White. For bisque order WP22003279. For the outer door panel in white order 22003242. Used on Maytag Neptunes.

This hinge cover is a small trim piece that conceals the door hinge and mounting screws. Replace a cracked or missing cover to restore a clean, finished look and help keep lint and debris out of the hinge cavity.

• Covers and protects the door hinge and screw heads
• Restores a smooth, finished appearance around the hinge opening
• Helps shield the hinge pocket from lint and debris
• Common replacement when the original cover is cracked, missing, or loose

• Disconnect power; for gas units, also shut off the gas supply
• Support the door; loosen/remove hinge screws as needed to access the cover
• Remove the damaged cover; position the new cover and secure per model design
• Verify door closes and aligns properly before returning to service

This door boot drain hose channels residual water from the lower edge of the washer's door boot back into the tub/drain path. Replacing a cracked or clogged hose helps prevent front leaks, standing water, and musty odors around the gasket.

• Directs water away from the door boot/gasket into the tub or drain circuit
• Common symptoms: water pooling in the boot, leak at the front base, or musty odor near the door
• Replace if the hose is cracked, brittle, kinked, blocked, or leaking
• Restores proper draining from the door seal area

• Disconnect power and turn off water supply before servicing
• Access the hose at the door boot and its mating port; place towels to catch residual water
• Transfer or replace clamps as needed; fully seat hose on fittings and orient clamps correctly
• Run a short test cycle and check for leaks

This 2-pack of dryer vent clamps secures the vent hose to the dryer outlet and the wall/vent hood. A tight connection helps maintain airflow, reduce lint leaks, and keep the duct from slipping off during use.

• Tightens around the vent hose to hold it securely to the dryer exhaust collar or exterior vent
• Helps prevent hose detachment, air leaks, and lint escaping at the connection
• Supports proper exhaust airflow by keeping connections sealed and stable
• Common symptoms pointing to replacement: hose won't stay on, visible gaps or lint around fittings, rattling at the vent, or longer dry times from poor ventilation

• Disconnect power; for gas dryers, shut off gas supply before moving the appliance
• Slide a clamp over the hose, seat the hose fully on the collar, position clamp over the fitting, and tighten with a screwdriver or nut driver
• Do not overtighten; avoid crushing thin foil ducting; ensure the hose is straight and not kinked
• Restore power and verify strong airflow at the exterior exhaust

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to maintain a secure seal
• Helps stop drips, seepage, or loose connections
• Common fix when you see moisture around a hose joint
• Useful if a clamp is rusted, stretched, or no longer holding tension

• Unplug power and shut off water (if applicable) before servicing
• Note clamp position/orientation before removal
• Use appropriate screwdriver or nut driver to tighten evenly
• Do not overtighten—ensure a snug, leak-free seal without damaging the hose

To order indicator light use WP903115.

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

This is the longer of the two dispenser lid hinge pins. For the shorter lid hinge pin order WPY912679.

Replacement door latch assembly that secures the appliance door during operation and helps the machine detect a closed door so cycles can start. Replaces a worn or damaged latch to restore reliable door closure and normal operation. What it does:

• Secures the door and maintains latch engagement during operation.
• Allows the appliance to recognize a closed door so cycles can begin.
• Commonly resolves symptoms such as the door not staying closed, the unit not starting, or a loose/unreliable latch.
• Reinstates proper mechanical engagement and alignment at the door mounting point.

What's included: One door latch assembly. Install notes:

• Disconnect power (and water supply if applicable) before beginning any repair.
• Remove the door panel or access screws as required; align the latch and fasten securely in the original orientation.
• Test door operation and cycle start before reassembling all panels.

NOTE: SAME AS 22003593 WITH NO IND LIGHT 

This is the shorter of the two dispenser lid hinge pins. For the longer lid hinge pin order WP6-912678.

This replacement screw secures appliance panels and components. Use this OEM fastener to swap out stripped, corroded, or missing hardware so assemblies stay tight, aligned, and quiet for reliable day-to-day operation.

• Provides secure attachment for panels, brackets, and internal assemblies
• Direct replacement for stripped, corroded, or lost screws
• Can help with symptoms like vibration, rattling, or loose/misaligned parts
• Supports proper fit to reduce gaps or unwanted movement

• Disconnect power; for gas or water appliances, shut off the supply before service
• Note hardware order and retain any spacers or clips from the original setup
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the mating part before installation

New seals come with this valve.

Pulley, spinner restores proper spinner rotation by guiding the spinner assembly and maintaining belt alignment. Replacing a worn or damaged pulley reduces noise and vibration during spin and helps improve water extraction. What it does:

• Guides and supports the washer's spinner assembly for smooth rotation and correct belt tracking.
• Common symptoms of a failing pulley: loud squealing or grinding during spin, wobbling spinner, belt slippage, or poor water extraction.
• Replaces a worn, cracked or noisy pulley to restore normal spin performance.

• Disconnect power (unplug or switch off breaker) and shut off water before servicing.
• Access the spinner area per your appliance's service guide—remove panels or agitator as needed to reach the pulley.
• Inspect belt, bearings and mounting hardware; replace any worn or damaged components at the same time.
• Follow manufacturer torque and reassembly instructions.

This valve seal kit provides replacement rubber seals for the appliance's water inlet valve assembly to help stop valve-area leaks and restore reliable water flow. Use when seals are cracked, flattened, or leaking. What it does:

• Replaces worn or damaged seals at the water inlet valve to help stop drips and leaks.
• Helps restore proper water fill behavior when leaks or spraying occur around the valve area.
• Prevents water from escaping at valve connections when seals have become hardened or compressed.
• Lets you refresh the valve sealing surface without replacing the entire valve body when the valve itself is undamaged.

• Turn off the appliance power and shut off the water supply before servicing.
• Inspect valve body and valve seat for corrosion or damage; replace the valve if the seat is compromised.
• Use appropriate hand tools and avoid over-tightening fittings when reassembling.

This 6-32 machine screw fastens brackets, panels, and internal components in your appliance. Replacing a missing or stripped screw restores a secure, rattle-free fit and keeps assemblies properly aligned during normal operation.

• Secures components to frames, brackets, or covers
• Helps maintain proper alignment of panels and hardware
• Replaces missing, damaged, or stripped fasteners
• Common signs: loose/rattling panels, misaligned parts, or a screw that won't tighten

• Disconnect power (and water, if applicable) before servicing
• Match thread and length to the original fastener; reuse any washers if present
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the driver that matches the head style on your original screw

• Thread size: 6-32 (machine screw)