Maytag Mah7500awq Serial Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: W10135699
The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.
This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22002263
The Dryer Light Bulb is an OEM part for Whirlpool dryers. This bulb is specifically designed to provide illumination inside the dryer drum, allowing for better visibility when loading and unloading laundry. It ensures a well-lit drying environment.
Causes of a bad dryer light bulb can include normal wear and tear, electrical issues, or accidental breakage.
Symptoms of a bad dryer light bulb may include:
- The bulb not turning on when the dryer door is open.
- Dim or flickering light inside the dryer drum.
- A burnt-out or broken bulb.
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Squeaky noise and not fully drying David H. • Santa Clarita , CA • September 20, 2019
Originally the dryer was squeaking a lot, so I purchased a new belt tensioner, but the original tensioner was an old-style no wheel tensioner, so that wasn't the source of the squeaking.
I saw a lot of lint had built up inside the unit where there shouldn't have been that much. So I viewed a few videos on the Appliance Pros site and saw that the rear wheel guides were the cause of the squeaking and the rear felt drum and blower housing seal needed to be replaced. The rear blower housing was...
Read more
More
$15.55
- Compare At:
-
$18.50
- You Save:
-
$2.95
Genuine Whirlpool part
By: Whirlpool
Part Number: WP25001052
The Drain Pump Assembly is an OEM part for Whirlpool front-loading washing machines. Located within the bottom of the tub housing, this assembly pumps water out through the drain hose during drain cycles. Efficient water removal relies on a functioning drain pump.
Causes of a drain pump failing can include clogs or mineral deposits obstructing the impeller over numerous washes. The electric motor inside may also degrade from extensive usage cycles.
Symptoms of a bad drain pump assembly include:
- Retained water remaining in the bottom of the washer tub
- Slow or incomplete draining at the end of cycles
- Gurgling or grinding noises from underneath the tub area
- Error codes related to overflow or drainage issues
This OEM Whirlpool part is compatible with KitchenAid, Jenn-Air, and some Kenmore front-loading washer models.
Do-It-Yourself Stories from Customers like You
Washer displayed error code and would not drain properly or complete a wash cycle Daniel D. • South Jordan , UT • October 06, 2014
I looked up the error code on the internet and determined that the drain pump had failed. I watched the Appliance Parts Pros repair video on how to replace this part, ordered a new pump and installed it myself in less than 30 minutes. This was an easy job that saved me the price of a service call, at least one hour of labor, and perhaps a markup on the part--probably around $200.00 total. I do this kind of work around the house a lot and win points with my wife. I still haven't received my...
Read more
More
$124.95
- Compare At:
-
$148.69
- You Save:
-
$23.74
Genuine Whirlpool part
By: Whirlpool
Part Number: 12001788
The Belt and Isolator Kit is an OEM part for Whirlpool washing machines. This kit includes a drive belt and isolators that work together to transfer motion from the motor to the washer drum while dampening vibrations.
Over time, the belt can wear out, stretch, or break due to regular use, heavy loads, or friction. The isolators may also deteriorate, losing their ability to absorb shocks effectively.
Symptoms of a bad Belt and Isolator Kit include:
- The drum not spinning or agitating
- Excessive vibration or noise during operation
- The washer failing to start or complete cycles
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
Will not agitate
-
Spins slowly
-
Burning smell
-
Pumps but will not spin
See more...
Do-It-Yourself Stories from Customers like You
Noisy spin cycle Gregory E. • Halifax , PA • April 17, 2017
I just wanted to put my experience here for all to see. I have a Maytag Neptune, MAH5500BWW, one of the original ones. I bought it back in 2002 and it has done many many loads of wash faithfully. So when the bearings started to get loud I thought it best to replace them, the seal kit and the belt. I did my research as best I could and decided to order the OEM parts from an appliance supplier. If you are replacing the bearings, watch on line videos prior to performing the job. It will...
Read more
More
$28.95
- Compare At:
-
$34.45
- You Save:
-
$5.50
Genuine Whirlpool part
By: Whirlpool
Part Number: WP596669
The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.
Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.
Symptoms of a bad hose clamp include:
- Leaks at the hose connection points
- Hoses slipping off the connections
- Visible rust or damage on the clamp
- Reduced appliance efficiency due to leaks
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
Will not stop filling with water
-
Leaking
See more...
Do-It-Yourself Stories from Customers like You
My washing machine smelt horrible Bryan W. • Ogdensburg , NY • August 20, 2018
First off I have to say that Appliance Parts Pro's saved me from hiring a repair person, and quite possibly just getting rid of my washing machine. Their video's helped out SOOOOOOOO much and the advice one of their agents gave me over their online chat helped me trouble shoot something when I got stuck. On top of this they shipped my parts fast enough that less than 12 hrs later they arrived, which allowed me to get my machine up and running way faster than the other options I had available....
Read more
More
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22003593
The Washer Door Latch Assembly is an OEM part for Whirlpool washing machines. This assembly is crucial for securing the washer door during operation, ensuring that the door remains closed and locked while the machine is in use. This helps prevent water leaks and ensures that the wash cycle completes safely and effectively.
You should replace the door latch assembly if it becomes faulty or damaged. Causes of a bad door latch assembly can include wear and tear over time, mechanical failure, or accidental damage from forcefully closing the door. A malfunctioning latch can prevent the washer from starting or cause it to stop mid-cycle.
Symptoms of a bad door latch assembly include:
- The washer door not locking or staying closed
- The washer not starting or pausing mid-cycle
- Error codes related to door lock issues displayed on the control panel
- Water leakage around the door area during operation
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
NOTE: Washer door latch, gray w/switches and ind. Light
This part fixes the following symptoms
-
Lid or door will not open
-
Won't start
-
Lid or door won't close
See more...
Do-It-Yourself Stories from Customers like You
The door wouldn't close on my Maytag Neptune Washer John K. • Pittsburgh , PA • March 21, 2014
I ordered the part from AppliancePartsPros. It arrived within 48 hours. I then followed the instructional video to switch out the Door Latch Assembly. A very good experience for a total novice. Thank you.
Read more
More
$196.70
- Compare At:
-
$234.07
- You Save:
-
$37.37
Genuine Whirlpool part
By: Whirlpool
Part Number: WP285655
The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.
Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.
Symptoms of a bad hose clamp include:
- Water leaks around the hose connection points
- The hose slipping off the fitting
- Visible rust or wear on the clamp
- Difficulty in tightening the clamp to secure the hose
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Syphonbreak was leaking James O. • Bryant , AL • September 04, 2015
We ordered parts from appliance parts pros and I fixed it.
Read more
More
$9.95
- Compare At:
-
$11.74
- You Save:
-
$1.79
Genuine Whirlpool part
By: Whirlpool
Part Number: 12002022
The Lip Seal Kit is an OEM replacement part for Whirlpool washing machines. It contains new seals that surround the tub opening and help prevent water leaks. This lip seal kit includes the revised lip seal, grease, O-ring, seal tool, washer kit, and instructions. The rear bearings are sold separately. Their part numbers are WP22003441 and WP22002934.
Symptoms of failed lip seals include:
- Water leaks from around the washer opening or tub area
- Puddles or standing water underneath after a cycle
- Visible cracks or splits in existing seals
Causes may involve standard wear from machine operation, rubbing against the tub surface. Mineral buildup can also shorten seal lifespan if not periodically cleaned.
This OEM Whirlpool part fits models by Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washing machines.
Do-It-Yourself Stories from Customers like You
Noisy spin cycle Gregory E. • Halifax , PA • April 17, 2017
I just wanted to put my experience here for all to see. I have a Maytag Neptune, MAH5500BWW, one of the original ones. I bought it back in 2002 and it has done many many loads of wash faithfully. So when the bearings started to get loud I thought it best to replace them, the seal kit and the belt. I did my research as best I could and decided to order the OEM parts from an appliance supplier. If you are replacing the bearings, watch on line videos prior to performing the job. It will...
Read more
More
$79.95
- Compare At:
-
$95.14
- You Save:
-
$15.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP90767
The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.
This part fixes the following symptoms:
- Loose or wobbly components within the appliance
- Panels or parts that are not securely attached
- Rattling or unusual noises due to loose parts
- Damaged or missing screw
The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
Do-It-Yourself Stories from Customers like You
Certain buttons were'not working Brent T. • Easton , MD • November 17, 2014
One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS!
p.s. In doing my research come to find Maytag did little to insulate control panel from oven...
Read more
More
$7.95
- Compare At:
-
$9.46
- You Save:
-
$1.51
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22003834
For machine with 4 coil valve use part #WP22003245.
This part fixes the following symptoms
-
No hot or cold water
-
Will not stop filling with water
-
Will not fill with water
See more...
Do-It-Yourself Stories from Customers like You
Leaking valve washer filled with water when not in use opened door of front loader and water flooded out Roy B. • Santee , CA • September 01, 2014
Purchased replacement fill valve.
Read more
More
$108.55
- Compare At:
-
$130.26
- You Save:
-
$21.71
Genuine Whirlpool part
By: Whirlpool
Part Number: WP89503
Size: 5 foot long. Rubber fill hose used on most automatic washing machines. Two hoses used per machine.
Do-It-Yourself Stories from Customers like You
Low water flow and fabric softener would dispense immediately when cycle started Bob G. • Sylacauga , AL • January 19, 2019
Replaced flow meter and control valve
Read more
More
$16.59
- Compare At:
-
$19.58
- You Save:
-
$2.99
Genuine Whirlpool part
By: Whirlpool
Part Number: WP210684
The Leveling Leg Pad is an OEM replacement part for Whirlpool washing machines. This small but essential component fits beneath the leveling legs, providing stability and preventing the appliance from moving or vibrating excessively during operation. It also protects flooring surfaces from potential scratches or damage.
Symptoms of a bad Leveling Leg Pad include:
- Increased vibration or noise during the wash or spin cycle
- The washing machine wobbling or becoming unsteady
- Visible wear, cracks, or damage to the pad
Causes of a failing Leveling Leg Pad can include wear and tear from prolonged use, exposure to moisture, or excessive weight causing deformation. Replacing worn pads helps maintain the appliance's balance and efficiency.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
For the leveling leg order 22003428.
Do-It-Yourself Stories from Customers like You
Washer "bucking" while in spin cycle Luis P. • Loveland , CO • June 27, 2017
New leveler pads
Read more
More
$10.95
- Compare At:
-
$13.14
- You Save:
-
$2.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22004477
This door boot drain hose channels residual water from the lower edge of the washer's door boot back into the tub/drain path. Replacing a cracked or clogged hose helps prevent front leaks, standing water, and musty odors around the gasket.
- Directs water away from the door boot/gasket into the tub or drain circuit
- Common symptoms: water pooling in the boot, leak at the front base, or musty odor near the door
- Replace if the hose is cracked, brittle, kinked, blocked, or leaking
- Restores proper draining from the door seal area
What's included: 1 drain hose Install notes:
- Disconnect power and turn off water supply before servicing
- Access the hose at the door boot and its mating port; place towels to catch residual water
- Transfer or replace clamps as needed; fully seat hose on fittings and orient clamps correctly
- Run a short test cycle and check for leaks
Do-It-Yourself Stories from Customers like You
Leaking from tub assembly and intermittent motor operation James F. • North Pole , AK • October 20, 2015
Basically rebuilt the washer from the ground up. Spent more money than a new washer but we have been so happy with the way this machine has worked over the last 19 years figured it would be money well spent.
Read more
More
$48.95
- Compare At:
-
$58.25
- You Save:
-
$9.30
Genuine Whirlpool part
By: Whirlpool
Part Number: WP696392
This 2-pack of dryer vent clamps secures the vent hose to the dryer outlet and the wall/vent hood. A tight connection helps maintain airflow, reduce lint leaks, and keep the duct from slipping off during use.
- Tightens around the vent hose to hold it securely to the dryer exhaust collar or exterior vent
- Helps prevent hose detachment, air leaks, and lint escaping at the connection
- Supports proper exhaust airflow by keeping connections sealed and stable
- Common symptoms pointing to replacement: hose won't stay on, visible gaps or lint around fittings, rattling at the vent, or longer dry times from poor ventilation
What's included: Two vent clamps Installation notes:
- Disconnect power; for gas dryers, shut off gas supply before moving the appliance
- Slide a clamp over the hose, seat the hose fully on the collar, position clamp over the fitting, and tighten with a screwdriver or nut driver
- Do not overtighten; avoid crushing thin foil ducting; ensure the hose is straight and not kinked
- Restore power and verify strong airflow at the exterior exhaust
More
$6.62
- Compare At:
-
$7.28
- You Save:
-
$0.66
Genuine Whirlpool part
By: Whirlpool
Part Number: WP616099
This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.
- Tightens around a hose and fitting to maintain a secure seal
- Helps stop drips, seepage, or loose connections
- Common fix when you see moisture around a hose joint
- Useful if a clamp is rusted, stretched, or no longer holding tension
What's included: One hose clamp. Install notes:
- Unplug power and shut off water (if applicable) before servicing
- Note clamp position/orientation before removal
- Use appropriate screwdriver or nut driver to tighten evenly
- Do not overtighten—ensure a snug, leak-free seal without damaging the hose
Do-It-Yourself Stories from Customers like You
Water leak Steven K. • New City , NY • August 10, 2018
Took off cover, installed new parts.
Read more
More
$9.95
- Compare At:
-
$11.59
- You Save:
-
$1.64
Genuine Whirlpool part
By: Whirlpool
Part Number: WP489503
This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.
- Fastens a hose to a barb or port to prevent leaks
- Helps keep hoses from slipping off due to vibration or pressure
- Restores proper sealing when a clamp is rusted, bent, or stripped
- Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten
What's included: 1 hose clamp Install notes:
- Disconnect power and shut off the water supply before servicing
- Place a towel to catch residual water when removing hoses
- Position the clamp just behind the hose barb/bead and secure with the appropriate tool
- Restore water and power, then run a quick check for leaks at the connection
Do-It-Yourself Stories from Customers like You
The maytag washer was leaking water during fillup and rinse Lucian L. • Addison , IL • October 06, 2014
I ordered the required parts from your website, the parts required were easily identified
from the website tub blowup. The parts were delivered within 2 days and installed within
15 minutes
Read more
More
$7.49
- Compare At:
-
$8.99
- You Save:
-
$1.50