Maytag Mdg9316aww Parts

• Noisy

In the past, I replaced some electronic components on our gas dryer, the solenoid and the electronic ignitor, but the rest of the dryer looked more difficult to repair if needed in the future. I was wrong. I went unto AppliancePartsPros.com and watched some repair videos on dryers like mine that make big thumping sounds while drying. This happened when I googled my dryer model number in an attempt to find out is capacity, because I wanted our new dryer to have the same capacity. I found out... Read more

Saw a video on line. Looked fairly easy to replace, but there were quite a few steps. I followed the video step for step and had the motor out in less than an hour. Tested motor with an electrical tester, just to be sure that was the problem. I ordered the motor from Appliance Parts Pros on a Sunday evening. The motor was at my doorstep Tuesday morning. It took about a hour and half to get everything back together. My only suggestion would be to label all the screws as to where they go as you... Read more

Our Maytag gas clothes dryer was not drying like it should/used to and was making a lot of noise. After researching online I figured the vent was partially blocked and/or the blower wheel was bad. When I took it apart, the vent had very little lint in the lower elbow exiting the back of the dryer but the blower wheel was loose on the shaft and was missing the clamp. I cleaned out the vent and put a hose clamp on the blower wheel to tighten it to the shaft and tried it again. The noise was... Read more

An appliance repair man in area did repairs, the screws were not easy to find and none were supplied with baffles! Read more

For several months we could smell a slight odor of propane in the laundry room and wondered why, just didn't seem like it was enough to be overly concerned, but thought something must be wrong with the dryer, but it was still working. We just didn't know how inefficiently. Then the extra time it took to dry a load of clothes progressively seemed to get longer, but things still seemed to work fine and the clothes got dried, given enough time. Then approximately 3 weeks ago we noticed the dryer... Read more

• Will not tumble

First replaced the drum rollers...that wasn't it..took dryer back apart and spun the belt tension wheel by hand (should have done this the first time I took the dryer apart) and it squeaked. so I ordered the full parts: wheel, idler arm, idler spring, arm sleeve, E ring..Put it back together and whoa..no more squealing!! Read more

• No heat or not enough heat
• Takes too long to dry
• Noisy

Our Maytag gas clothes dryer was not drying like it should/used to and was making a lot of noise. After researching online I figured the vent was partially blocked and/or the blower wheel was bad. When I took it apart, the vent had very little lint in the lower elbow exiting the back of the dryer but the blower wheel was loose on the shaft and was missing the clamp. I cleaned out the vent and put a hose clamp on the blower wheel to tighten it to the shaft and tried it again. The noise was... Read more

I replaced drum rollers, axle shafts and front bearing kit. Still had noise. Ordered Idler Arm, Belt Tension Pulley & Washers. I ordered parts at 3:30 pm on a Wednesday, received new parts at 11:30 am Thursday. The instructions & videos were very simple to follow and provided excellent tips. Back up and running with silence in an 1/2 hour. My 13 year old dryer is running like new again. Way cheaper than calling a repairman. Read more

• Door won't close

Took off front cover of drier, removed old part and just snapped in new part. Read more

• Door won't close
• Shuts off too soon
• Doesn't shut off
• Takes too long to dry

Ordered a new clip and installed it. Easy to do. Unplugged the dryer. Removed the front. It is only held on by two screws. Removed wires to the door switch. removed the female end (it had the broken male piece in it. Inserted the new female part in the front, clipped in the male part into the door and reconnected the door switch wires, screwed the front back on. Job done. Total time was less than 10 minutes. Works like new. Read more

Through 15 years of vibration, the Cycling Thermostat evidently had degraded to the point where one electrical connection or more came loose and caused a short. There is also a possibility that the Bakelite section of the Dryer Cycling Thermostat body separated from the metal base, simultaneously exposing all four connections to a short. The thermostat literally exploded into chunks and dust. There was a heavy arcing and then, thankfully, the thermal fuse blew and shut down power to the short... Read more

• Doesn't shut off
• Won't start

It's working now Read more

I replaced drum rollers, axle shafts and front bearing kit. Still had noise. Ordered Idler Arm, Belt Tension Pulley & Washers. I ordered parts at 3:30 pm on a Wednesday, received new parts at 11:30 am Thursday. The instructions & videos were very simple to follow and provided excellent tips. Back up and running with silence in an 1/2 hour. My 13 year old dryer is running like new again. Way cheaper than calling a repairman. Read more

One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS! p.s. In doing my research come to find Maytag did little to insulate control panel from oven... Read more

It's working now Read more

It took me about 2 hours to take everything apart and get it back together & running again with no problems. All the parts I ordered were exactly what I needed to fix everything. Thank you all !!! Read more