Rf20hfenbsr Parts

• Ice maker dispenses too much ice
• Ice maker not making ice

Since I could not find the correct thermistor from the schematic provided, I ordered the thermistor harness for the evaporator. I cut the harness and spliced it to the sheared thermistor wires on the roof of the freezer compartment. It now works fine with a little "farmer ingenuity" help. Samsung was absolutely no help at all, but the guy that I spoke with over the phone at APP sure was. This site is now my "go to" for appliance parts! Tip for others with this model. Do not overfill the upper... Read more

Replaced all 3 gaskets with gaskets from appliancepartspros.com. Gaskets took less than 10 minutes to replace and fit perfect! I checked the refrigerator and freezer compartments approx 6 hrs later and found the compartments to be a few degrees colder. Freezer ice was cold and loose, not stuck together. It's like having a new refrigerator! Read more

New assembly. Read more

Found one of the drain valves was clogged causing condensation to overflow on the floor behind the refrigerator. Order the parts on Monday morning and they arrived tuesday afternoon. Replace both of the valves in 15 minutes. Easy repair and save a bundle over a service call. Read more

Took a bit to diagnose. First tried cleaning coils but the problem still persisted. Next took of the back panel and put the system into diag mode. (Press energy save button and fridge button for eight seconds system ding once a second and inverter board red LED will blink a code or be on solid if no issue. See back of the refrigerator for a sticker with what the number of blinks means. My unit one blinking 1 time. So I measured the resistance of the compressor between windings (8.9 ohms between... Read more

I took all the items out of the refrigerator. Removed the screws that hold the cover over the evaporator motor. Than for three hours used a hair drier to remove ice. The panel was frozen on if you pull on it it will break. Soaked up all the water removed the panel and took the fan blade off. That was difficult because it looks like a regular screw head however, you need to push in that which will cause it to release the blades and than push it onto the new motor. Than replace the panel put the... Read more

Ordered the two motors plus ordered the fan blades since I was afraid one might break during replacement. Changed out without breaking Freezer and both ice makers now working fine Read more

• Noisy

I bought new parts, motor and fan. Replace the old one. Took me no more than 15 minutes to fix it. Read more

Replaced all 3 gaskets with gaskets from appliancepartspros.com. Gaskets took less than 10 minutes to replace and fit perfect! I checked the refrigerator and freezer compartments approx 6 hrs later and found the compartments to be a few degrees colder. Freezer ice was cold and loose, not stuck together. It's like having a new refrigerator! Read more

I started by replacing the water filter assembly since it was leaking after I attempted to install a non-name-brand filter. The new assembly didn't fix the problem (but was hard to find, and AppliancePartsPros was amazing in being able to get one). Further, while replacing that I noticed that the previous owner had literally cut out the grounding pin from the power cord. I decided to replace the power cord and the Ice Maker Assembly. None of the online stores seemed to have either part listed... Read more

Knowing from a previous repair, that there was only 3 parts that could be bad. I decided if I was going to take it apart to change all 3. Not having the proper test equipment, it was cheaper to replace the 3 parts than pay a repair person. Read more

I bought the defrost-clip (clip-drain-evap), but once I took the refrigerator apart--the large plastic "back" had frozen to the rest and left the insulation in pieces when I tried to pull it apart. I was able to replace the clip-drain-evap piece with little trouble once the ice had melted, but I was unhappy with the looks of the "back". So I ended up ordering a new "back"(Yassy cover-evap) that included the new insulation as it's made in one unit. Once it arrived, replacing the new "back"... Read more

I replaced the temperature sensor, the thermo fuse, and the heating element that thaws the evaporator on a cycle to keep the evaporator from freezing up. The most time consuming part of the repair was waiting for the fridge to thaw out so that I could remove the cover. I disconnected the fridge the night before and placed a fan on low with the doors open so that it was thawed out when I awoke. It was easy to remove the evaporator cover once I removed all of the shelves. I took pics as i was... Read more

Ordered the replacement cap handles (left and right side), and replaced them. Replacing was a breeze, but removing the old broken part was a bit challenging. There was a small metal rod that needed to be slid out for the old part to come out, but it was not easy to do. I used screwdriver and pliers for like 30 minutes to slide out the metal rod. Otherwise, everything else was easy to do. Read more

• Leaking
• Not dispensing water
• Noisy

Verified that the water line had flowing water, check. Removed lower screen and vacuumed and cleaned all dust. Proceeded to test water flow to the valve and beyond the valve. The valve did not allow water to pass through it. Nor would it open or close. Went to Marbeck for confirmation and was sent to your website for the part. Read more

Knowing from a previous repair, that there was only 3 parts that could be bad. I decided if I was going to take it apart to change all 3. Not having the proper test equipment, it was cheaper to replace the 3 parts than pay a repair person. Read more