Sav151deww Parts

This spring fastener applies constant tension to hold a component securely in place inside your appliance, helping prevent looseness, vibration, or gaps. Replacing a fatigued or missing clip restores a tight, reliable fit.

• Provides spring tension to clamp and retain a part, seal, or panel
• Helps maintain alignment and reduce vibration or rattling
• Restores secure attachment when the original clip is bent, stretched, or missing
• Symptoms can include a part not staying put, visible looseness, or a clip that's damaged or gone

• Disconnect power; turn off water supply if applicable
• Use needle-nose pliers or a suitable spring tool; wear gloves and eye protection
• Note the original orientation before removal to ensure proper reinstallation
• Make sure the mating part or seal is fully seated and the fastener is fully engaged before reassembly

This replacement main bearing assembly supports the washer's drive/spin system. It keeps the inner basket and drive shaft rotating smoothly and quietly, helping maintain alignment and reducing vibration during wash and high-speed spin.

• Supports and centers the spin basket/drive shaft for low-friction rotation
• Helps reduce noise and vibration when spinning at high RPMs
• Restores smooth operation when the original bearing is worn or rough
• Common symptoms: roaring/grinding during spin, basket wobble/play, roughness turning by hand, possible leak at rear center if related seal wear is present

• Disconnect power and water before service; allow the appliance to cool
• Access and replacement procedures vary by model; significant disassembly is typical
• A bearing press/driver may be required; inspect shaft and related seals and replace if worn
• After reassembly, run a test spin to check for leaks

This washer drain hose channels used water from the pump to your home drain. A sound, properly routed hose helps prevent leaks and backups during the drain cycle for reliable performance and a cleaner laundry area.

• Routes wastewater from the drain pump to the standpipe or laundry tub
• Replaces hoses that are cracked, brittle, split, kinked, or leaking
• Common fix for leaks at the back of the washer or slow/failed draining
• Restores a secure, watertight path when correctly clamped and routed

• Disconnect power and turn off water; expect some residual water—use towels or a pan
• Wear gloves; edges and clamps can be sharp
• Transfer and reuse existing clamps/brackets if your model uses them; ensure snug connections at both ends
• Route to the manufacturer-recommended height and secure to the standpipe; avoid kinks and test drain

Leg, adjustable (w/nut)

One piece. Works on most Maytag washers. Color: white. It measures about 5 inches in diameter, and 5-1/2 inches high.

This small retaining clip secures components in place inside the appliance, helping prevent movement, vibration, and premature wear. Replace a bent, fatigued, or missing clip to restore a solid, factory-tight hold.

• Holds panels, brackets, or tubing securely in their mounts
• Helps maintain alignment to reduce rattles, rubbing, or intermittent issues
• Common signs of failure: missing clip, loose fit, buzzing/vibration, parts that won't stay seated
• Restores proper retention after service, transport, or vibration-related fatigue

• Disconnect power and shut off gas/water before servicing
• Note the original clip's orientation; remove with needle-nose pliers
• Seat the new clip fully—do not over-bend; spring tension provides the hold
• Test operation before reassembly

This pressure switch hose carries air from the washer tub to the pressure switch so the machine can sense and control water level. Replacing a damaged hose restores proper fill control and prevents level-sensing errors. What it does:

• Channels air/vacuum from the tub to the pressure switch so the control can detect water level.
• A cracked, pinched, or collapsed hose may cause overfilling, underfilling, failure to advance cycles, or continuous fill.
• Restores accurate water-level sensing when replacing a worn or damaged hose.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Remove and replace the hose carefully; avoid kinks, sharp bends, or pinched routing that can impair sensing.
• Use the factory-style connection points and clamps; ensure both ends are seated securely.
• After installation, run a test fill or diagnostic cycle to confirm correct water-level operation and no leaks.

This cycle selector knob is used on some Maytag washers and dryers. This is not the timer knob. Color: stainless steel. Measures about 2 inches in diameter where the handle extends.

Can be upper or lower bearing depending on application.

This selector knob attaches to the control shaft so you can choose cycles and options on your appliance. Replace a cracked or stripped knob to restore smooth, accurate settings without forcing or damaging the control stem.

• Attaches to the control shaft to operate the cycle/timer or option switch
• Common symptoms: knob is cracked, stripped, loose, spins freely, falls off, or is missing
• Restores positive, accurate control feel when selecting settings

• Disconnect power before servicing
• Pull the old knob straight off the shaft; avoid prying against the control panel
• Align the keyed/flat side and press the new knob on until fully seated
• If your original knob used a spring clip or insert, transfer it to the new knob before installation

Specs: No.8X1/2 HEX WASHER HEAD

This 12-14 x 1/2 screw is a factory fastener used to secure appliance panels, brackets, and components. Replacing a missing or stripped screw restores a tight fit, reduces rattling, and keeps parts properly aligned for reliable operation.

• Secures panels, brackets, and internal components to their mounting points
• Replaces damaged, rusted, or missing hardware
• Helps stop vibration and rattling caused by loose fasteners
• Restores proper alignment and stability of covers or assemblies

• Disconnect power and, if applicable, shut off gas/water before servicing
• Match the original screw's location and length; replace one at a time
• Start threads by hand to prevent cross-threading; tighten snugly without over-torquing
• Reinstall any original washers, clips, or spacers used with the screw

This standpipe adapter connects the appliance drain hose to the household standpipe or waste outlet, helping ensure a secure drain path and reduce the risk of leaks or poor drainage. Simple replacement for damaged or worn connectors. What it does:

• Provides a sealed connection between the appliance drain hose and the standpipe or drain outlet
• Prevents water leaks at the hose-to-standpipe junction
• Helps maintain proper drainage and reduces gurgling or slow-draining symptoms
• Durable plastic construction designed to resist cracking and wear under normal use

• One standpipe adapter

• Turn off and unplug the appliance and stop water flow before replacing the adapter
• Remove the old adapter and clean the mating surfaces; ensure the hose and standpipe are free of debris
• Slide the drain hose onto the adapter fully and secure with the proper clamp or retainer
• If you find cracks in nearby hoses or fittings, replace those parts as needed and test for leaks after installation

This tub-to-pump drain hose carries wash water from the washer tub to the drain pump so the machine can pump out during drain cycles. It replaces a cracked, split, or clogged hose to stop leaks and restore proper draining. What it does

• Directs tub water to the drain pump during drain and spin cycles
• Seals at tub and pump connections with hose clamps to prevent leaks
• Restores normal draining when original hose is damaged, cracked, or collapsed
• Helps prevent water on the floor and washer failure-to-drain symptoms

• Disconnect power and turn off water supply before starting any repair
• Remove lower access panel or cabinet to access hose and clamps
• Inspect and reuse or replace clamps as needed; secure hose ends evenly to avoid leaks
• Route hose without sharp bends or kinks; check for leaks after reconnecting power and running a short cycle

This spring hook tool helps remove and reinstall suspension and drive springs safely and precisely, making spring service or drum suspension work easier and more controlled for technicians and DIYers. What it does:

• Provides a secure hook for grabbing and manipulating washer/dryer springs
• Helps install or remove springs during suspension, tub, or agitator repairs
• Reduces risk of spring slippage compared with improvised tools
• Useful when addressing noisy, off-balance, or uneven-spinning washers caused by spring or suspension issues

• Always disconnect power and water supply before servicing appliances
• Wear eye protection and gloves; springs are under tension and can snap back
• Use the tool only for its intended spring tasks and follow OEM service procedures

A replacement nut-lock used to secure fasteners and keep panels or components from backing off due to vibration. Simple, durable hardware that restores a secure connection and reduces rattling or loose parts. What it does:

• Secures a mating bolt or stud to prevent loosening from vibration or movement
• Restores a solid attachment for panels, brackets, or assemblies that may come loose
• Helps eliminate symptoms such as rattling, vibrating, or intermittent panel movement
• Suitable where a locking fastener is required to maintain a reliable connection

• Disconnect power and follow appliance safety procedures before starting work
• Locate the matching stud or bolt and remove the old fastener if present
• Use the correct-size wrench or socket and tighten until the nut-lock seats; avoid over-tightening
• Inspect threads and mating hardware for damage; replace damaged components