Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix water leaks from your washer's drain system. This drain hose assembly channels wastewater properly. Easy DIY repair with back panel removal.
This is an easy fix. Just remove the back panel, remove the hose clamp to pull out the old hose, put the new hose on, make sure the clamp is well centered onto the connection, and return the back panel. Make sure to insert the drain hose into the three plastic guides that prevent the hose from moving around. The Samsung factory did not do this on my original hose, which is why it failed, because it was rubbing against the tub support and it wore a hole into the hose. I am going to complain... Read more
Fixes loud banging noise and excessive vibration during spin cycle. Secures counterbalance weight to prevent dancing and movement. DIY-friendly repair.
Needed to replace washer counter balance. Also order shock absorbers in case they needed to be replaced, fortunately they didn't need replacement and will be returned. I used Appliance Parts Pros many time and always found them to be very helpful and the repair videos are very helpful. Read more
Fix a washer that won't fill with water or leaks onto the floor. This water inlet valve controls water flow into your machine. DIY repair in 10 minutes.
The Cold Water Inlet Valve had a very good You Tube Video and I followed it. One note of caution, as I chuckled at the guy on the video saying watch for sharp edges, he was correct. When removing one of the lines from the valve, my pliers slipped and my elbow hit the front of the machine(inside edge) and cut my elbow. So after that I draped the edges with towels to avoid that happening. Again the fix was easy and very straight forward from the video. No extra pearls of wisdom here. Total... Read more
Fix tE error codes with a new water temperature thermistor. This sensor monitors wash water temp. DIY-friendly repair takes under 10 minutes.
I first check the schematics to find the heat sensor. On my model it's c on the control panel. I checked the continuity on the orange and white wires. It showed some continuity but not much. I then went to the heater element and found the orange and white wires going to the thermistor. Turns out the heater element and thermistor need repalced. Read more
Replacement glass panel for washer door. Installs on front-load washer doors. Order when glass is cracked, shattered, or broken. Includes installation video.
I looked up my model number on the site, and found my parts needed. J then watched a video from repair clinic on you tube. The video was sr sight forward, and made the repair easy. I have repaired washers and dryers for numerous people following the same process. Doing this has saved hundreds of dollars in labor charges. Read more
Replace your washer's door boot seal when you notice water leaks, mold, or visible tears. Ensures a watertight seal during wash cycles. Verify fit by model.
I ordered new door gasket, front and rear clamp for gasket and installed them. Read more
Washer won't start or door won't open? A faulty door lock assembly is the likely cause. This repair takes about 15 minutes with basic tools.
Ordered part took seal off to gain access..couple of screws and connectors..bk in business Read more
Fix a washer door that won't close or latch with this door lock assembly. Easy DIY repair takes 10-15 minutes with video instructions. No need to disassemble.
Ordered part by looking at parts diagram and followed You tube instructions. Easy and quick! Read more
Fix water leaks behind the detergent drawer with this washer upper nozzle connector. Located under the top panel. Easy 5-minute DIY repair with basic tools.
When I opened the rear cover and check the temperature sensor, I noticed the wire connection was damp. I dried it up with a hair dryer and it worked again for a few days. Then the problem came back. When I gone back to inspect the second time, i noticed a lot of water on the floor. I knew there was a leak. I followed the disassemble samsung washer video from "Repair clinic.com" to open the top cover, then i realized the assembly hose was busted. I ordered the parts from this site and... Read more
Fix ND error codes and drainage issues with this washer check valve. Prevents backward water flow in drain pump. DIY-friendly repair with video guide.
Washer said error no drain. Cleaned the filter and still no drain. So the next step was to check the hose for any debris and when I went to pull the hose off it broke, at the same time I found the check valve flap broke in the drain pump and it was blocking the hose. So I replaced the check valve on the drain pump and replaced the hose. Read more
Fix leaks or mold buildup with a new washer drain hose. Channels water away from the drum. Moderate DIY repair—requires back panel removal.
Bought and installed a new drain hose. It required removing the back access panel and loosening a pinch clamp that holds the hose on its male outlet end, and threading the hose out the back of the washer. Read more
Broken or missing dispenser tray leg causing water buildup? This washer detergent tray snaps into place in under 10 minutes. Easy DIY fix for Samsung models.
Replaced with new Detergent cup and fill cap. Cup symphony perfectly. Simple fix for frustrating problem. Read more
Fixes E3 error codes, grinding noises during spin, and loud tapping sounds. This brushless DC motor assembly restores power to washing cycles.
Actually, I am returning your parts. THERE IS NOTHING WRONG WITH THEM! My wife actually found out that we had a warranty on our washer that we didn't know about. But, I can comment that I did chat with your customer service and you guys were very helpful. Read more
Traps lint, coins, and debris to protect your washer's drain pump. Replace if clogged, leaking, or threads are damaged. Confirm fit with your model number.
Looking at the schematics from the manufacturer, I could not tell if it was suppose to have a washer. I called Appliance Parts Pros and the gentleman looked at the part he had in stock and found it did require a washer. Not really happy about it, but paid to have it repaired. Thank you Appliance Parts Pros! Read more
Fix a washer stuck mid-cycle or showing overfill errors with a new water level pressure switch. This part detects water levels to control fill cycles.
Machine was a front load washer, after doing some research found that problem is usually caused by pressure sensor or the spider arm which attaches motor to tub. Read more
Supports the drum and absorbs vibrations to reduce noise and prevent walking during spin cycles. Replace if washer is unbalanced or excessively noisy.
Replaced all four shocks and both springs. Read more