Whirlpool Adg 954/1 Parts

This door seal replaces a worn or damaged gasket around the oven door, creating a tight barrier between the door and the front frame. A fresh seal helps the appliance heat efficiently and maintain steady cooking temperatures. What it does:

• Seals the gap between the door and oven frame to minimize heat loss
• Helps the oven preheat faster and hold set temperatures more consistently
• Replace if the gasket is torn, brittle, flattened, or frayed
• Common signs include heat escaping around the door edge and longer cook times

• 1 door seal

• Disconnect power and allow the oven to cool completely before beginning
• Open the door and carefully remove the old seal, noting its routing and attachment points
• Clean the mating surface to remove debris for a proper seal
• Install the new seal evenly without stretching; ensure all ends and anchors are fully seated

This dryer exhaust fan is used on many Admiral, Crosley, Hoover, Magic Chef, Maytag, Montgomery Ward and Norge brands. Size: 3-1/8 inches deep, 8 inch fin diameter, 7-1/8 inch hub diameter, 20 standard fins, 1/2 inch diameter motor shaft, 7/16 inch motor shaft diameter to flat side of shaft. Blower wheel clamp not included. For the clamp order WP312967.

This lint filter cover fits over the dryer's lint screen opening to secure the filter and provide a smooth, directed airflow path. Replace a cracked or missing cover to help maintain lint capture and protect fabrics at the opening.

• Covers the lint filter opening and holds the screen in place
• Guides air through the filter to collect lint
• Provides a smooth edge to help prevent fabric snags at the drum entrance
• Typical signs of failure: cracked/broken cover, loose or mis-seated lint screen, excess lint in the drum, or longer dry times

• Disconnect power; for gas models, shut off the gas supply
• Open the door and remove the lint screen
• Remove the existing cover by releasing its fasteners/tabs (varies by model); note orientation
• Seat the new cover securely and reinstall the lint screen; verify proper fit before use

This kit replaces a temperature-control thermostat and its mounting plate in select dryers. It helps restore accurate heat regulation and consistent cycling, protecting against overheating and poor drying results when the original thermostat or bracket has failed.

• Senses exhaust air temperature and opens/closes contacts to control the heater
• Helps maintain consistent drying temperatures and safe operation
• Failure symptoms include no heat, insufficient heat, overheating, or erratic cycling
• Mounts with the included plate to ensure proper positioning of the thermostat

• Disconnect power before servicing; for gas units, also shut off gas supply
• Access the thermostat location (typically on the blower/exhaust housing); note wire positions and transfer one at a time
• Attach the thermostat to the plate and secure the assembly using existing hardware if new fasteners are not provided
• After reassembly, verify proper airflow and clean the lint path and venting

The Screw is an OEM part for Whirlpool refrigerators. This screw secures the refrigerator door hinge in place, allowing the door operates smoothly and seals properly. 

Over time, screws can become loose or go missing during repairs or adjustments, which can lead to a misaligned door, compromised sealing, and increased energy consumption. 

Symptoms of a bad screw include:

• The refrigerator door seems misaligned or does not close properly.
• Increased effort needed to open or close the door.
• Unusual gaps around the door seal when closed.
• The door might squeak or make other noises during operation.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This idler assembly is the spring-loaded belt tensioner that keeps the drive belt correctly tightened. Replacing a worn or seized idler restores smooth belt tracking, reduces squeal, and helps prevent slippage or loss of drive.

• Maintains proper tension on the drive belt for reliable power transfer
• Helps prevent belt slippage, squealing, or the belt coming off the pulleys
• Supports smooth rotation of the driven components
• Failure symptoms can include noise from the belt path, a frayed or derailed belt, or loss of motion

• Disconnect power and allow all moving parts to stop before servicing
• Access the belt path; relieve belt tension and remove the old idler assembly
• Install the new assembly; ensure the pulley spins freely and the belt is centered in the groove
• Manually rotate the system to verify alignment and clearances before restoring power

This replacement idler pulley keeps the drive belt tight and tracking correctly so the drum can rotate smoothly. It restores quiet, consistent operation when the original pulley is worn or seized and causing belt slippage or noise.

• Maintains proper tension on the drive belt to enable smooth drum rotation
• Provides a low-friction surface for the belt to ride on and stay aligned
• Common symptoms of failure: squealing/chirping, belt fraying or coming off, burning rubber smell, or a drum that won't turn
• Replace if the pulley wobbles, binds, or the rim/bearing is worn

• Disconnect power; if gas, shut off the gas supply
• Note belt routing, relieve tension from the idler arm, and remove the belt from the motor pulley
• Remove the retaining hardware from the old pulley, install the new pulley on the idler arm shaft, and re-tension the belt
• Manually rotate the drum to verify smooth belt tracking before reassembly and test run

This replacement screw secures appliance panels and components so they stay tight and aligned during use. Replacing a missing or damaged screw restores a solid fit and helps eliminate rattles, loose trim, or shifting parts.

• Fastens brackets, panels, trim, or components to the appliance chassis
• Helps correct loose or missing hardware after vibration or service
• Replaces stripped, rusted, or broken screws
• Can reduce rattling noises or misaligned parts caused by missing fasteners

• Disconnect power; for gas appliances, also shut off the gas supply
• Support the part being fastened; start threads by hand to avoid cross-threading
• Use the correct driver size; tighten snugly without overtightening
• Replace hardware with the exact part number to ensure proper fit

The Outlet Cover is an OEM part for SpeedQueen dryers. It is a protective plate located at the rear of the dryer that covers the outlet vent during operation. The outlet cover plays an important safety role by preventing objects from accidentally entering the vent area.

Causes of a bad outlet cover can include normal wear and tear over extended use, damage from being struck or impacted, or loose screws/fasteners that no longer hold it tightly in place.

Symptoms of a bad dryer outlet cover include:

• Cracks, fractures or missing pieces that compromise the cover's protective function
• Looseness, rattling or inability to properly secure over the outlet vent

This light gray lint filter cover shields the dryer's lint screen opening and helps direct airflow for efficient lint capture. Replace a cracked or missing cover to maintain airflow and reduce the chance of fabric snags.

• Covers the lint screen opening and channels air through the filter
• Helps keep the lint screen aligned and properly seated
• Provides a smooth edge at the door opening to protect fabrics
• Typical signs it's failing: cracks, broken tabs, loose lint screen, lint in drum, longer dry times

• Disconnect power before servicing
• Open the door; remove screws or release locking tabs to remove the old cover
• Position the new cover and secure it with existing hardware as applicable
• The lint screen slides in fully and seats flush before use

A high-limit thermostat that stops the dryer's heating circuit if internal temperatures get too high, helping prevent overheating and protecting heating components. Replaces a failed high-limit thermostat to restore overheat protection. What it does

• Opens the heating circuit when dryer temperature exceeds the thermostat set point to prevent overheating.
• Commonly related symptoms: dryer runs but produces little or no heat, dryer gets unusually hot, or the thermal cutoff repeatedly fails.
• Works as part of the dryer's temperature-safety system to protect heating elements, fuses, and internal wiring.

• One high-limit thermostat

• Disconnect power before accessing the dryer and work only after panels are cool.
• Take a photo or label wires before removal to ensure correct reconnection.
• Test the thermostat for continuity with a multimeter to confirm failure before replacing.
• If other safety devices (thermal fuse, cycling thermostat, element) show symptoms, inspect and test those components too.

This sensor monitors operating conditions and relays accurate feedback to the control so cycles run properly. Replacing a failed sensor helps restore correct operation and prevent erratic behavior or fault codes. What it does:

• Detects a specific operating condition and sends a signal to the control
• Helps the machine regulate cycle timing and performance
• Can cause error codes, cycles that won't start or advance, or intermittent shutdowns when failing
• Lead to inconsistent temperatures or sensing behavior depending on application

• 1 sensor

• Disconnect power (and shut off gas/water, if applicable) before servicing
• Access the sensor; note wire positions and connector orientation
• Install the new sensor in the same location and orientation; seat connectors fully
• Clear any stored faults and run a test cycle per the tech sheet

This thermostat regulates your dryer's operating temperature for consistent, safe drying. The pink/white variant restores correct heat cycling when the original control fails, helping prevent overheating or underheating that leads to long dry times.

• Monitors dryer air temperature and opens/closes to control the heater or burner
• Helps maintain even drying performance and protect against overheating
• Failure symptoms can include runs too hot, takes too long to dry, no heat, or heat that won't shut off
• Color-coded pink/white version—use only the variant specified for your model

• Disconnect power (and gas, if applicable) and allow the dryer to cool before servicing
• Access the thermostat per your model's procedure; it is typically mounted to a housing surface for proper sensing
• Move wires one at a time to the new thermostat, matching positions as shown in the instruction sheet
• Reassemble, restore power, and run a test cycle to confirm proper heat cycling and airflow

This terminal block assembly connects your dryer's power cord to the internal wiring, providing a secure, heat-resistant junction. Replacing a damaged block restores a reliable electrical connection and helps prevent intermittent power, overheating, or burnt terminals.

• Provides an insulated junction point between incoming power and the appliance's internal wiring
• Secures cord conductors with screw terminals to maintain a tight, low-resistance connection
• Helps resolve issues like the dryer not powering on, intermittent shutdowns, or a burning smell near the cord cover
• Replaces cracked, melted, or stripped terminals to restore a safe power path

• Disconnect power at the breaker before servicing
• Photograph/label wire positions and move one wire at a time to the new block
• Tighten terminal screws firmly; recheck connections after initial operation
• Inspect/replace any heat-damaged cord lugs, wiring, or strain relief before reassembly

This door strike bracket mounts to the cabinet and positions the door strike so the door latches securely and the machine recognizes a closed door. Replace a bent or broken bracket to restore proper door alignment and reliable starts.

• Supports and aligns the door strike with the latch/lock assembly
• Ensures the door switch/interlock is engaged when the door is shut
• Helps prevent nuisance "door open" messages and cycles that won't start
• Direct replacement for a damaged, bent, or missing bracket

• Disconnect power before servicing; shut off water or gas supplies if applicable
• Open the door and access the bracket from the front panel area
• Note bracket orientation; transfer and install using existing hardware; align before tightening
• After reassembly, the door closes firmly and the machine starts without a door error

This replacement moisture sensor bar mounts inside the drum and helps the dryer detect when laundry is dry. A worn or damaged bar can cause sensor-dry cycles to end too soon or run too long.

• Senses moisture on fabrics and signals the control to advance or extend auto-dry cycles
• Helps stop the cycle when clothes reach the selected dryness level
• Symptoms can include auto-dry cycles ending early, extended run times, or inconsistent dryness
• Build-up on the bars can also affect sensing performance

• Disconnect power before servicing; shut off gas supply for gas dryers
• Access the sensor at the front bulkhead/lint housing; move wire leads to the new bar and secure with existing hardware
• Clean any residue from both sensor bars to improve accuracy
• Reassemble and test with a small damp load on a sensor cycle