Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Drain hose carries used water from washer to household drain. Replace if cracked, leaking, deteriorated, or damaged to prevent water overflow issues.
I replaced the Tube to pump hose which was very easy. I just tilted the washer on it side and replaced the Hose. Read more
Central hub that connects the inner tub to the drive shaft in washers. Replace if corroded, cracked, or arms have broken off causing wobble or imbalance.
Looked online at several websites to see if I could figure out the problem Came across AppliancePartsPros video on replacing bearings. Watched it a couple of times and determined (well, guessed) it was the bearings and/or spider. Followed the video (great job by the way) and disassembled the washer. The spider was cracked on one arm so ordered a new one from this site. I also ordered two new bearings and the bearing seal b/c learned from the web and local appliance store that they go bad in 7+... Read more
Fix detergent not dispensing or a broken dispenser drawer. This washer detergent box assembly holds and releases soap properly. DIY-friendly repair.
I replaced the dispenser assembly and since this was being replaced, I installed a new drawer and detergent box assembly. Read more
Washer won't fill or rinse properly? A faulty circulation pump motor prevents water flow during wash cycles. Moderate DIY repair, 1-2 hours.
Replaced the drain pump and circulating pump units. Read more
Fix TE error code on your washer with this thermistor assembly. Monitors water temperature during wash cycles. DIY-friendly repair with video guide.
Replaced thermistor Read more
Shipping bolt assembly secures the washer drum during transport. Replace if bolts are lost, damaged, or missing before moving your washer to prevent damage.
AppliancePartsPros had the needed items in stock, and I had them within 48 hours of the parts being shipped. Read more
Secures the inner door gasket to prevent water leaks during wash cycles. Replace if gasket is loose or leaking. Confirm fit with your model number.
The upper counter-balance weight mount design is a poor design to begin with. It started to rattle loose approximately 5yrs into the 8yrs that we've owned it. As it would start to loosen up (as evidenced by the loud banging noise exhibited during operation); I'd shut it down, pull the top off, remove the weight (it was almost always half rattled off at this point), wrap the mount lugs with friction tape (the plastic lugs were being worn down/chaffed by the balance weight), put the weight back... Read more
Washer won't spin or shows LE error code? The stator assembly converts power to spin the drum. Moderate repair, typically takes 30-60 minutes with video.
Swapped bad part for new part. Read more
Fix detergent not dispensing or leaking from drawer. This dispenser assembly includes compartments for detergent, bleach, and softener. 15-minute DIY repair.
Hinge pin locks shock absorbers to the washer drum assembly. Replace if broken, worn, or when installing new shock absorbers. Installs at dampener mount.
I opted to save myself about $600 by repairing my 8 year old LG washing machine rather than buying a new one. After watching some videos I determined what I needed upon taking my washing machine apart. I ended up replacing the tub (includes spider and shaft), since I could not get the spider part removed from the original tub, as well as the motor bolt (which had broken when I removed it from the original tub's shaft). The spider was cracked and the shaft was wobbling which caused it to... Read more
Fix grinding noises or a drum that won't spin with this washer motor rotor assembly. Common when spline teeth strip. Moderately difficult repair.
I looked on the internet for similar descriptions for similar models and found many angry reports. Most said that the rotor assembly was bad as the nut that held the rotor and other parts together had loosened and allowed slippage between steel and plastic splines. Yes, I know that sounds like trouble, but apparently not to LG when they designed it. Most buyers complained that the part was covered by warrantee but not the labor and labor had been quoted as $400 to $600 dollars. Time to buy... Read more
Fix a washer that won't power on or turn on with this noise filter assembly. Common cause when display won't light up. Easy DIY repair, plug and play.
Searched the web and determined it was something called a noise filter. Ordered the part from ApplianceParts Pros. Received it in about 3 days, normal shipping. Replaced the part. Took about 15 minutes from start to finish. Problem solved. Cost less than $50. Read more
Replaces cracked or rotted washer vent hose that causes moisture buildup and leaks. Ensures proper air circulation to prevent mildew. Verify fit.
Removed the top cover while the machine was operating, located the source of the leak. The top filler tube had worn a hole in a flex point. Found the right part on this site, replaced it with little effort. While in there I saw a similar hose and decided to replace it as its time was probably up too. So far so good, washing clothes and no leaks!! Great prices and best of all the right parts were delivered in a timely manner. Thanks for making this so easy. Only specialty tool used was hose... Read more
Secures hose connections in your washer to prevent leaks. Replace if you notice water leaking or loose hose fittings. Verify fit with your model number.
If your LG Front load washers sounds like a freight train, STOP USING IT. You're doing more damage and will need more parts to fix it. After the noise became unbearable, I began to explore and disassemble. I knew enough to know the bearings must be bad but had never done this repair before. ( I am however pretty mechanically inclined.) Watch this video before you start tearing your LG apart. APP did a great job explaining the steps of the repair. Do a search on this site or youtube.com with... Read more
Washer leaking from inlet valve or not filling properly? This three-coil water inlet valve assembly controls cold water, bleach, and prewash. DIY fix in 15-30 minutes.
1. I unplugged the washer from outlet 2. I turned off the hot and cold water taps going to the washer (both just in case) 3. Draped a towel over back edge of washer and under where hoses coming from water outlets attach to back of washer (to catch any loose water out of the hose or screw nozzle leading to valve assembly, then unscrew (by hand) the cold water hose from back of washer (leave hot water hose alone as not needed). 4. Unscrew valve assembly from washer by two screws on back top of... Read more
Washer won't spin or makes grinding noises? The motor rotor bolt secures the rotor to the motor shaft. Requires a 17mm socket for installation.